Administrace komentářů

Zdravim, mam naistalovane openSUSE 10.3 64bit na pocitaci ASUS pundit AH1, od pocatku mam problemy s ACPI abych spustil instalaci musel jsem nabootovat jadro bez ACPI, po instalaci ovsem nefungovalo vypinani PC musel jsme vypinat rucne. Hledam jsem na netu a laboroval jsem s parametry jadra v grubu (ACPI=on, force, apod) docilil jsem vzdy stavu ze bud byl system stabilni ale nesel vypinat a nebo sel vypinat ale nebyl stabilni. Rozhodl jsem se pro stabilitu a vratil jsem parametry na puvodni apm = off acpi = off mce=off barrier=off ide=nodma idewait=50 i8042 .nomux psmouse.proto=bare pci=nommconf resume=/dev/sda5 splash=silent prekvapilo me, ze sel pocitac vypnou ale zaroven cas od casu nahodne vytuhne. Zkousel jsem Memtest, ale pameti jsou v poradku.

Nemohl byste mi nekdo poradit v cem by mohl byt problem? Zda se mi ze ackoliv v grubu mam ACPI =off tak stejne se s nim neco dela viz dmesg.

dmesg mi pise napr:

Linux version 2.6.22.16-0.1-default (geeko@buildhost) (gcc version 4.2.1 (SUSE L
inux)) #1 SMP 2008/01/23 14:28:52 UTC
Command line: root=/dev/disk/by-id/scsi-SATA_WDC_WD1600YS-01_WD-WCAP02333550-par
t4 vga=0x31a apm = off acpi = off mce=off barrier=off ide=nodma idewait=50 i8042
.nomux psmouse.proto=bare pci=nommconf resume=/dev/sda5 splash=silent
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003def0000 (usable)
BIOS-e820: 000000003def0000 - 000000003def3000 (ACPI NVS)
BIOS-e820: 000000003def3000 - 000000003df00000 (ACPI data)
BIOS-e820: 000000003e000000 - 0000000040000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
Malformed early option 'acpi'
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 253680) 1 entries of 3200 used
end_pfn_map = 1048576
DMI 2.4 present.
ACPI: RSDP 000F6D20, 0024 (r2 Nvidia)
ACPI: XSDT 3DEF30C0, 004C (r1 _ASUS_ Notebook 42302E31 AWRD 0)
ACPI: FACP 3DEFA300, 00F4 (r3 _ASUS_ Notebook 42302E31 AWRD 0)
ACPI: DSDT 3DEF3240, 7055 (r1 _ASUS_ Notebook 1000 MSFT 3000000)
ACPI: FACS 3DEF0000, 0040
ACPI: SLIC 3DEFA500, 0176 (r1 _ASUS_ Notebook 42302E31 AWRD 0)
ACPI: SSDT 3DEFA6C0, 00D3 (r1 _ASUS_ Notebook 1 LTP 1)
ACPI: HPET 3DEFA800, 0038 (r1 _ASUS_ Notebook 42302E31 AWRD 98)
ACPI: MCFG 3DEFA880, 003C (r1 _ASUS_ Notebook 42302E31 AWRD 0)
Scanning NUMA topology in Northbridge 24
No NUMA configuration found
Faking a node at 0000000000000000-000000003def0000
Entering add_active_range(0, 0, 159) 0 entries of 3200 used
Entering add_active_range(0, 256, 253680) 1 entries of 3200 used
Bootmem setup node 0 0000000000000000-000000003def0000
No mptable found.
Zone PFN ranges:
DMA 0 -> 4096
DMA32 4096 -> 1048576
Normal 1048576 -> 1048576
early_node_map[2] active PFN ranges
0: 0 -> 159
0: 256 -> 253680
On node 0 totalpages: 253583
DMA zone: 56 pages used for memmap
DMA zone: 1268 pages reserved
DMA zone: 2675 pages, LIFO batch:0
DMA32 zone: 3412 pages used for memmap
DMA32 zone: 246172 pages, LIFO batch:31
Normal zone: 0 pages used for memmap
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: HPET id: 0x10de8201 base: 0xfefff000
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 00000000000f0000
swsusp: Registered nosave memory region: 00000000000f0000 - 0000000000100000
Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000)
SMP: Allowing 0 CPUs, 0 hotplug CPUs
PERCPU: Allocating 50296 bytes of per cpu data
Built 1 zonelists. Total pages: 248847
Kernel command line: root=/dev/disk/by-id/scsi-SATA_WDC_WD1600YS-01_WD-WCAP02333
550-part4 vga=0x31a apm = off acpi = off mce=off barrier=off ide=nodma idewait=5
0 i8042.nomux psmouse.proto=bare pci=nommconf resume=/dev/sda5 splash=silent
bootsplash: silent mode.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Extended CMOS year: 2000
time.c: Detected 1808.326 MHz processor.
Console: colour dummy device 80x25
Checking aperture...
CPU 0: aperture @ e6fa000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Memory: 990824k/1014720k available (2053k kernel code, 23508k reserved, 1017k da
ta, 316k init)
Calibrating delay using timer specific routine.. 3619.76 BogoMIPS (lpj=7239535)
Security Framework v1.0.0 initialized
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 128K (64 bytes/line)
CPU 0/0 -> Node 0
SMP alternatives: switching to UP code
Freeing SMP alternatives: 24k freed
Unpacking initramfs... done
Freeing initrd memory: 4407k freed
ACPI: Core revision 20070126
Parsing all Control Methods:
Table [DSDT](id 0001) - 1346 Objects with 101 Devices 349 Methods 41 Regions
Parsing all Control Methods:
Table [SSDT](id 0002) - 4 Objects with 0 Devices 0 Methods 0 Regions
tbxface-0587 [00] tb_load_namespace : ACPI Tables successfully acquired
ACPI: setting ELCR to 0200 (from 0c20)
evxfevnt-0091 [00] enable : Transition to ACPI mode successful
weird, boot CPU (#0) not listed by the BIOS.
SMP motherboard not detected.
Using local APIC timer interrupts.
result 12557827
Detected 12.557 MHz APIC timer.
SMP disabled
Brought up 1 CPUs
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using configuration type 1
evgpeblk-0956 [00] ev_create_gpe_block : GPE 00 to 1F [_GPE] 4 regs on int 0x9
evgpeblk-0956 [00] ev_create_gpe_block : GPE 20 to 5F [_GPE] 8 regs on int 0x9
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 7 Wake, Enabled 1 Runtime GPEs
in this block
evgpeblk-1052 [00] ev_initialize_gpe_bloc: Found 0 Wake, Enabled 0 Runtime GPEs
in this block
ACPI: EC: Look up EC in DSDT
Completing Region/Field/Buffer/Package initialization:..........................
................................................................................
....
Initialized 37/41 Regions 9/9 Fields 35/35 Buffers 29/45 Packages (1359 nodes)
Initializing Device/Processor/Thermal objects by executing _INI methods:...
Executed 3 _INI methods requiring 1 _STA executions (examined 106 objects)
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Transparent bridge - 0000:00:10.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 *11 14 15)
ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled.
ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
hpet0: at MMIO 0xfefff000, IRQs 2, 8, 31
hpet0: 3 32-bit timers, 25000000 Hz
ACPI: RTC can wake from S4
pnp: 00:01: ioport range 0x4000-0x407f has been reserved
pnp: 00:01: ioport range 0x4080-0x40ff has been reserved
pnp: 00:01: ioport range 0x4400-0x447f has been reserved
pnp: 00:01: ioport range 0x4480-0x44ff has been reserved
pnp: 00:01: ioport range 0x4800-0x487f has been reserved
pnp: 00:01: ioport range 0x4880-0x48ff has been reserved
pnp: 00:01: ioport range 0x2000-0x207f has been reserved
pnp: 00:01: ioport range 0x2080-0x20ff has been reserved
pnp: 00:01: iomem range 0x3e000000-0x3fffffff could not be reserved
pnp: 00:0b: iomem range 0xf0000000-0xf3ffffff could not be reserved
pnp: 00:0c: iomem range 0xf0000-0xf3fff could not be reserved
pnp: 00:0c: iomem range 0xf4000-0xf7fff could not be reserved
pnp: 00:0c: iomem range 0xf8000-0xfbfff could not be reserved
pnp: 00:0c: iomem range 0xfc000-0xfffff could not be reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:10.0
IO window: c000-cfff
MEM window: fdd00000-fddfffff
PREFETCH window: fde00000-fdefffff
PCI: Setting latency timer of device 0000:00:10.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 6, 262144 bytes)
TCP established hash table entries: 131072 (order: 9, 3145728 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
audit(1202154724.472:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:00:05.0
vesafb: framebuffer at 0xe0000000, mapped to 0xffffc20000600000, using 10240k, t
otal 32768k
vesafb: mode is 1280x1024x16, linelength=2560, pages=1
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture...
bootsplash: silentjpeg size 98233 bytes
bootsplash: ...found (1280x1024, 35219 bytes, v3).
Console: switching to colour frame buffer device 156x60
fb0: VESA VGA frame buffer device
Real Time Clock Driver v1.12ac
hpet_resources: 0xfefff000 is busy
Non-volatile memory driver v1.2
Linux agpgart interface v0.102 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input0
input: PC Speaker as /class/input/input1
NET: Registered protocol family 1
IO APIC resources could be not be allocated.
Freeing unused kernel memory: 316k freed
SCSI subsystem initialized
libata version 3.00 loaded.
pata_amd 0000:00:0d.0: version 0.3.8
PCI: Setting latency timer of device 0000:00:0d.0 to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6 bmdma 0x00
0000000001f400 irq 14
ata2: PATA max UDMA/133 cmd 0x0000000000010170 ctl 0x0000000000010376 bmdma 0x00
0000000001f408 irq 15
ata1.00: ATAPI: Optiarc DVD RW AD-7173A, 1-01, max UDMA/66
ata1.00: configured for UDMA/66
ata2: port disabled. ignoring.
scsi 0:0:0:0: CD-ROM Optiarc DVD RW AD-7173A 1-01 PQ: 0 ANSI: 5
sata_nv 0000:00:0e.0: version 3.4
ACPI: PCI Interrupt Link [LSID] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [LSID] -> GSI 10 (level, low) -> IRQ
10
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi2 : sata_nv
scsi3 : sata_nv
ata3: SATA max UDMA/133 cmd 0x00000000000109f0 ctl 0x0000000000010bf2 bmdma 0x00
0000000001e000 irq 10
ata4: SATA max UDMA/133 cmd 0x0000000000010970 ctl 0x0000000000010b72 bmdma 0x00
0000000001e008 irq 10
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-7: WDC WD1600YS-01SHB1, 20.06C06, max UDMA/133
ata3.00: 321672960 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
ata4: SATA link down (SStatus 0 SControl 300)
scsi 2:0:0:0: Direct-Access ATA WDC WD1600YS-01S 20.0 PQ: 0 ANSI: 5
ACPI Exception (processor_core-0789): AE_NOT_FOUND, Processor Device is not pres
ent [20070126]
ACPI: Thermal Zone [THRM] (40 C)
ACPI: Fan [FAN] (on)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUBA] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LUBA] -> GSI 10 (level, low) -> IRQ
10
PCI: Setting latency timer of device 0000:00:0b.0 to 64
ohci_hcd 0000:00:0b.0: OHCI Host Controller
ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:0b.0: irq 10, io mem 0xfe02f000
sd 2:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sd 2:0:0:0: [sda] 321672960 512-byte hardware sectors (164697 MB)
usb usb1: new device found, idVendor=0000, idProduct=0000
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: OHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.22.16-0.1-default ohci_hcd
usb usb1: SerialNumber: 0000:00:0b.0
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 7 ports detected
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1 sda3 < sda5 sda6 > sda4
sd 2:0:0:0: [sda] Attached SCSI disk
ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [LUB2] -> GSI 5 (level, low) -> IRQ
5
PCI: Setting latency timer of device 0000:00:0b.1 to 64
ehci_hcd 0000:00:0b.1: EHCI Host Controller
ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:0b.1: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:0b.1
ehci_hcd 0000:00:0b.1: irq 5, io mem 0xfe02e000
ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: new device found, idVendor=0000, idProduct=0000
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.22.16-0.1-default ehci_hcd
usb usb2: SerialNumber: 0000:00:0b.1
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 7 ports detected
swsusp: Marking nosave pages: 000000000009f000 - 0000000000100000
swsusp: Basic memory bitmaps created
swsusp: Basic memory bitmaps freed
Attempting manual resume
usb 2-6: new high speed USB device using ehci_hcd and address 4
usb 2-6: new device found, idVendor=0424, idProduct=2228
usb 2-6: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-6: Product: Flash Card Reader
usb 2-6: Manufacturer: ASUS
usb 2-6: SerialNumber: 000022272228
usb 2-6: configuration #1 chosen from 1 choice
usb 1-3: new full speed USB device using ohci_hcd and address 2
usb 1-3: new device found, idVendor=03f0, idProduct=6004
usb 1-3: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-3: Product: deskjet 5550
usb 1-3: Manufacturer: hp
usb 1-3: SerialNumber: MY26K1J1XW2L
usb 1-3: configuration #1 chosen from 1 choice
usb 1-4: new low speed USB device using ohci_hcd and address 3
usb 1-4: new device found, idVendor=15d9, idProduct=0a33
usb 1-4: new device strings: Mfr=0, Product=1, SerialNumber=0
usb 1-4: Product: USB Mouse
usb 1-4: configuration #1 chosen from 1 choice
usbcore: registered new interface driver hiddev
input: USB Mouse as /class/input/input2
input: USB HID v1.10 Mouse [USB Mouse] on usb-0000:00:0b.0-4
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda4, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
scsi 0:0:0:0: Attached scsi generic sg0 type 5
sd 2:0:0:0: Attached scsi generic sg1 type 0
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4c00
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4c40
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 0:0:0:0: Attached scsi CD-ROM sr0
input: Power Button (FF) as /class/input/input3
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input4
ACPI: Power Button (CM) [PWRB]
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt Link [LNK7] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:05.0[A] -> Link [LNK7] -> GSI 10 (level, low) -> IRQ
10
PCI: Setting latency timer of device 0000:00:05.0 to 64
NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.09 Fri Jan 11 14:04:37 PST
2008
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 0 alt 0 pr
oto 2 vid 0x03F0 pid 0x6004
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.60.
ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [LMAC] -> GSI 11 (level, low) -> IRQ
11
PCI: Setting latency timer of device 0000:00:14.0 to 64
forcedeth: using HIGHDMA
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 4
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
rtc_cmos 00:05: rtc core: registered rtc_cmos as rtc0
rtc_cmos: probe of 00:05 failed with error -16
parport_pc 00:09: reported by Plug and Play ACPI
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
eth0: forcedeth.c: subsystem: 01043:816a bound to 0000:00:14.0
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:03.0[A] -> Link [LNK4] -> GSI 10 (level, low) -> IRQ
10
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[10] MMIO=[fddff000-fddff7ff] Max
Packet=[2048] IR/IT contexts=[4/8]
ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 5
ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [LAZA] -> GSI 5 (level, low) -> IRQ
5
PCI: Setting latency timer of device 0000:00:10.1 to 64
scsi 4:0:0:0: Direct-Access ASUS Flash HS-CF 3.95 PQ: 0 ANSI: 0
sd 4:0:0:0: [sdb] Attached SCSI removable disk
sd 4:0:0:0: Attached scsi generic sg2 type 0
scsi 4:0:0:1: Direct-Access ASUS Flash HS-COMBO 3.95 PQ: 0 ANSI: 0
sd 4:0:0:1: [sdc] Attached SCSI removable disk
sd 4:0:0:1: Attached scsi generic sg3 type 0
usb-storage: device scan complete
ieee1394: Host added: ID:BUS[0-00:1023] GUID[0011d800014cec5f]
Adding 2939852k swap on /dev/sda5. Priority:-1 extents:1 across:2939852k
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
loop: module loaded
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
AppArmor: AppArmor initialized
audit(1202154742.941:2): type=1505 info="AppArmor initialized" pid=2022
powernow-k8: Found 1 AMD Sempron(tm) Processor 3200+ processors (version 2.00.00
)
powernow-k8: 0 : fid 0xa (1800 MHz), vid 0xc
powernow-k8: 1 : fid 0x2 (1000 MHz), vid 0x12
Marking TSC unstable due to cpufreq changes
Time: hpet clocksource has been installed.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
Mobile IPv6
ip6_tables: (C) 2000-2006 Netfilter Core Team
ip_tables: (C) 2000-2006 Netfilter Core Team
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (3963 buckets, 31704 max)
NET: Registered protocol family 17
audit(1202151163.583:3): audit_pid=2976 old=0 by auid=4294967295
bootsplash: status on console 0 changed to on
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
eth0: no IPv6 routers present
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-OUT-ERROR IN= OUT=eth0 SRC=10.0.0.1 DST=193.86.85.18 LEN=52 TOS=0x00 PREC=0
x00 TTL=64 ID=58640 DF PROTO=TCP SPT=29847 DPT=80 WINDOW=1002 RES=0x00 ACK FIN U
RGP=0 OPT (0101080A0000B5F60050B6B1)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=10.0.0.1 DST=193.86.85.42 LEN=52 TOS=0x00 PREC=0
x00 TTL=64 ID=27377 DF PROTO=TCP SPT=2114 DPT=80 WINDOW=166 RES=0x00 ACK FIN URG
P=0 OPT (0101080A0000B6F501AA5240)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=10.0.0.1 DST=193.86.85.48 LEN=52 TOS=0x00 PREC=0
x00 TTL=64 ID=26928 DF PROTO=TCP SPT=10481 DPT=80 WINDOW=1002 RES=0x00 ACK FIN U
RGP=0 OPT (0101080A0000B7B701CCC2E1)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=10.0.0.1 DST=193.86.85.30 LEN=52 TOS=0x00 PREC=0
x00 TTL=64 ID=38236 DF PROTO=TCP SPT=20607 DPT=80 WINDOW=770 RES=0x00 ACK FIN UR
GP=0 OPT (0101080A0000B7F400FC6F6D)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=10.0.0.1 DST=193.86.85.46 LEN=52 TOS=0x00 PREC=0
x00 TTL=64 ID=49767 DF PROTO=TCP SPT=12720 DPT=80 WINDOW=108 RES=0x00 ACK FIN UR
GP=0 OPT (0101080A0000BAF100475F88)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=10.0.0.1 DST=193.86.85.48 LEN=52 TOS=0x00 PREC=0
x00 TTL=64 ID=41374 DF PROTO=TCP SPT=10482 DPT=80 WINDOW=498 RES=0x00 ACK FIN UR
GP=0 OPT (0101080A0000C9E201CCC0FB)
SFW2-OUT-ERROR IN= OUT=eth0 SRC=10.0.0.1 DST=193.86.85.48 LEN=52 TOS=0x00 PREC=0
x00 TTL=64 ID=26929 DF PROTO=TCP SPT=10481 DPT=80 WINDOW=1002 RES=0x00 ACK FIN U
RGP=0 OPT (0101080A0000F4B801CCC2E1)
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
SFW2-INext-DROP-DEFLT IN=eth0 OUT= MAC= SRC=10.0.0.1 DST=224.0.0.251 LEN=64 TOS=
0x00 PREC=0x00 TTL=255 ID=0 DF PROTO=UDP SPT=5353 DPT=5353 LEN=44
Eeek! page_mapcount(page) went negative! (-1)
page pfn = 20a51
page->flags = 100000000000014
page->count = 0
page->mapping = 0000000000000000
vma->vm_ops = _stext+0x7fdf9000/0x1a
------------[ cut here ]------------
kernel BUG at mm/rmap.c:628!
invalid opcode: 0000 [1] SMP
last sysfs file: /devices/system/cpu/cpu0/cpufreq/scaling_governor
CPU 0
Modules linked in: ip6t_LOG nf_conntrack_ipv6 xt_pkttype ipt_LOG xt_limit snd_pc
m_oss snd_mixer_oss snd_seq snd_seq_device af_packet ip6t_REJECT xt_tcpudp ipt_R
EJECT xt_state iptable_mangle iptable_nat nf_nat iptable_filter ip6table_mangle
nf_conntrack_ipv4 nf_conntrack nfnetlink ip_tables ip6table_filter ip6_tables x_
tables ipv6 cpufreq_conservative cpufreq_userspace cpufreq_powersave powernow_k8
apparmor loop dm_mod parport_pc parport rtc_cmos rtc_core rtc_lib snd_hda_intel
snd_pcm snd_timer k8temp ohci1394 usb_storage snd ide_core hwmon ieee1394 force
deth usblp serio_raw soundcore nvidia(P) button snd_page_alloc sr_mod cdrom i2c_
nforce2 i2c_core sg usbhid hid ff_memless sd_mod ehci_hcd ohci_hcd usbcore edd e
xt3 mbcache jbd fan thermal processor sata_nv pata_amd libata scsi_mod
Pid: 5085, comm: kio_http Tainted: P N 2.6.22.16-0.1-default #1
RIP: 0010:[] [] page_remove_rmap+0xed/0x108
RSP: 0018:ffff81002feb1db8 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff81003d8871b8 RCX: 00000000000064df
RDX: 00000000ffffffff RSI: 0000000000000046 RDI: ffffffff804bf01c
RBP: ffff810024c701e8 R08: 00000000fffffffd R09: 0000000000000020
R10: 0000000000000000 R11: 0000000000000000 R12: 0000000000633000
R13: ffff810023f12198 R14: ffff81000100b7d0 R15: 0000000000692000
FS: 00002b4eafb623e0(0000) GS:ffffffff80500000(0000) knlGS:00000000f7cec940
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002b4ea982ed30 CR3: 0000000023b8a000 CR4: 00000000000006a0
Process kio_http (pid: 5085, threadinfo ffff81002feb0000, task ffff81003afbb140)
Stack: 000000002f8c0020 ffff81003d8871b8 0000000020a51020 ffffffff802708b0
ffff810023efea60 ffffffff806167d0 0000000000691fff ffff81000100b7e8
0000000000691fff 0000000000691fff 0000000000000000 ffff81002feb1ed8
Call Trace:
[] unmap_vmas+0x40d/0x798
[] exit_mmap+0x78/0xed
[] mmput+0x28/0xa0
[] do_exit+0x23e/0x81e
[] sys_exit_group+0x0/0xe
[] system_call+0x7e/0x83

Code: 0f 0b eb fe 8b 77 18 5a 5b 5d 83 e6 01 f7 de 83 c6 04 e9 93
RIP [] page_remove_rmap+0xed/0x108
RSP
Fixing recursive fault but reboot is needed!
Bad page state in process 'kicker'
page:ffff81003d8871b8 flags:0x0100000000000014 mapping:0000000000000000 mapcount :-1 count:0
Trying to fix it up, but a reboot is needed
Backtrace:

Call Trace:
[] clear_page_c+0x7/0x10
[] bad_page+0x63/0x8d
[] get_page_from_freelist+0x362/0x545
[] __alloc_pages+0xad/0x33d
[] __handle_mm_fault+0x4cb/0xa3e
[] do_page_fault+0x400/0x769
[] thread_return+0x0/0xf1
[] do_mmap_pgoff+0x643/0x798
[] error_exit+0x0/0x84