Administrace komentářů

Zdravím. Pokusím se co nejpřesněji popsat problém, který mám.

Mám síťovou kartu Intel PRO/100 VE Network Connection. Pro upřesnění počítače mám notebook Fujitsu Siemens Amilo Pro V3205.

Jsem lehce pokročilý začínající uživatel Linuxu.( 4 měsíce, ale Debian jen 1 měsíc ).

Už po třetí mi nefunguje síťová karta v Debianu. Pokaždé se to stane když si nainstaluji nejnovější jádro, které potřebuji, jinak by jsem nemohl nikdy použít Wifi.

První dva problémy jsem řešil tak, že jsem přeinstaloval celý Debian, ale konfigurovat pokaždé vše znova včetně Ap.Mysq.Php se mi nechce a teď bych už rád přišel věci na kloub.

Debian jinak používám i na desktopu, kde jsem žádný takový problém nezaznamenal, ale tam je Realtek ETH.

Moduly jsem zkontroloval a e100 mám nainstalovaný.

Někdy síťovou kartu povolit jde, ale když jí pak zkusím přenastavit tak mi to napíše, systém nemohl povolit zařízení, zkontrolujte nastavění.

Přikládám ještě výpis ifconfig -a:

debian-lukas:/home/lukas# ifconfig -a
eth0      Zapouzdření:NEZNÁM  HWadr 00-C0-9F-00-00-B2-FF-C2-00-00-00-00-00-00-00-00
          inet adr:192.168.1.17  Všesměr:192.168.1.255 Maska:255.255.255.0
          VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:159 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          RX bytes:0 (0.0 b)  TX bytes:9491 (9.2 KiB)

eth1      Zapouzdření:Ethernet  HWadr 00:16:36:83:60:1F
          VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

lo        Zapouzdření:Místní smyčka
          inet adr:127.0.0.1 Maska:255.0.0.0
          inet6-adr: ::1/128 Rozsah:Počítač
          AKTIVOVÁNO SMYČKA BĚŽÍ  MTU:16436  Metrika:1
          RX packets:8 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          RX bytes:578 (578.0 b)  TX bytes:578 (578.0 b)

sit0      Zapouzdření:IPv6-in-IPv4
          NEARP  MTU:1480  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:0
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

plus výpis dmesg:

debian-lukas:/home/lukas# dmesg
Linux version 2.6.18-6-686 (Debian 2.6.18.dfsg.1-22etch2) (dannf@debian.org) (gc c version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Aug 18 08:42 :39 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001f690000 (usable)
 BIOS-e820: 000000001f690000 - 000000001f698000 (ACPI data)
 BIOS-e820: 000000001f698000 - 000000001f700000 (ACPI NVS)
 BIOS-e820: 000000001f700000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
502MB LOWMEM available.
found SMP MP-table at 000f76d0
On node 0 totalpages: 128656
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 124560 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f7590
ACPI: RSDT (v001 FUJ___ DW1_____ 0x20060721  LTP 0x00000000) @ 0x1f691e9c
ACPI: FADT (v001 FUJ___ DW1_____ 0x20060721 LOHR 0x0000005a) @ 0x1f697e20
ACPI: MADT (v001 FUJ___ DW1_____ 0x20060721 LOHR 0x0000005a) @ 0x1f697e94
ACPI: BOOT (v001 FUJ___ DW1_____ 0x20060721  LTP 0x00000001) @ 0x1f697fd8
ACPI: MCFG (v001 FUJ___ DW1_____ 0x20060721 LOHR 0x0000005a) @ 0x1f697f34
ACPI: MADT (v001 FUJ___ DW1_____ 0x20060721  LTP 0x00000000) @ 0x1f697f70
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20050228) @ 0x1f691ed8
ACPI: DSDT (v001 FUJ___ DW1_____ 0x20060721 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: 2 duplicate APIC table ignored.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1729.548 MHz processor.
Built 1 zonelists.  Total pages: 128656
Kernel command line: root=/dev/sda6 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 502068k/514624k available (1541k kernel code, 11916k reserved, 580k data , 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3463.28 BogoMIPS (lpj=6926566)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 0 0000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 0000000 0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel Genuine Intel(R) CPU           T2250  @ 1.73GHz stepping 08
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3459.36 BogoMIPS (lpj=6918731)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 0 0000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 0000000 0 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU           T2250  @ 1.73GHz stepping 08
Total of 2 processors activated (6922.64 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=55
checking if image is initramfs... it is
Freeing initrd memory: 4775k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Firmware left 0000:07:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15)
ACPI: Embedded Controller [EC0] (gpe 23) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
  IO window: 2000-2fff
  MEM window: da000000-dbffffff
  PREFETCH window: d4000000-d5ffffff
PCI: Bridge: 0000:00:1c.1
  IO window: 3000-3fff
  MEM window: d6000000-d7ffffff
  PREFETCH window: d0000000-d1ffffff
PCI: Bridge: 0000:00:1c.2
  IO window: 4000-4fff
  MEM window: d8000000-d9ffffff
  PREFETCH window: d2000000-d3ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 5000-5fff
  MEM window: dc000000-dc0fffff
  PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag value 0x82 read from CMOS RAM was invalid
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1224267921.180:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2F] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
Time: tsc clocksource has been installed.
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [ 20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [ 20060707]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [ 20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [ 20060707]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (55 C)
Time: acpi_pm clocksource has been installed.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 225, io base 0x00001820
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
libata version 2.00 loaded.
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 233, io base 0x00001840
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ieee1394: Initialized config rom entry `ip1394'

-----------------------------------------------------------------------------------------------------------------
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
-----------------------------------------------------------------------------------------------------------------

ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001860
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 177, io base 0x00001880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-2: new full speed USB device using uhci_hcd and address 2
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 233
usb 1-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
usb 2-1: new low speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver hiddev
input: Genius Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:1d.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ata1: SATA max UDMA/133 cmd 0xE00F4500 ctl 0x0 bmdma 0x0 irq 50
ata2: SATA max UDMA/133 cmd 0xE00F4580 ctl 0x0 bmdma 0x0 irq 50
ata3: SATA max UDMA/133 cmd 0xE00F4600 ctl 0x0 bmdma 0x0 irq 50
ata4: SATA max UDMA/133 cmd 0xE00F4680 ctl 0x0 bmdma 0x0 irq 50
scsi1 : ahci
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi2 : ahci
ata2: SATA link down (SStatus 0 SControl 0)
scsi3 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
scsi4 : ahci
ata4: SATA link down (SStatus 0 SControl 0)
  Vendor: ATA       Model: FUJITSU MHW2120B  Rev: 0000
  Type:   Direct-Access                      ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 225, io mem 0xdc444000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda:<6>usb 1-2: USB disconnect, address 2
 sda1 sda2 < sda5 sda6 sda7<6>ACPI: PCI Interrupt 0000:07:08.0[A] -> GSI 20 (lev el, low) -> IRQ 58
PCI: Setting latency timer of device 0000:07:08.0 to 64
 sda8 >
sd 1:0:0:0: Attached scsi disk sda
e100: eth0: e100_probe: addr 0xdc000000, irq 58, MAC addr 00:16:36:83:60:1F
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
ICH7: chipset revision 2
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
usb 5-2: new high speed USB device using ehci_hcd and address 2
usb 5-2: configuration #1 chosen from 1 choice
scsi5 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb 2-1: USB disconnect, address 2
hda: HL-DT-ST DVDRAM GSA-T10N, ATAPI CD/DVD-ROM drive
usb 2-1: new low speed USB device using uhci_hcd and address 3
usb 2-1: configuration #1 chosen from 1 choice
input: Genius Optical Mouse as /class/input/input2
input: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:1d.1-1
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
PCI: Enabling device 0000:07:09.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:07:09.0[A] -> GSI 20 (level, low) -> IRQ 58
PCI: Setting latency timer of device 0000:07:09.0 to 64
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[58]  MMIO=[dc001000-dc0017ff]  Max  Packet=[2048]  IR/IT contexts=[4/4]
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00c09f0000b2ffc2]
ts: Compaq touchscreen protocol output
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
intel_rng: FWH not detected

input: PC Speaker as /class/input/input3
Real Time Clock Driver v1.12ac
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:07:09.1 [1180:0822] (rev 19)
PCI: Enabling device 0000:07:09.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:07:09.1[B] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:07:09.1 to 64
mmc0: SDHCI at 0xdc001800 irq 66 DMA
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 233
Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input4
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1b.0 to 64
  Vendor: Verbatim  Model: Store 'n' Go      Rev: 1.30
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sdb: 2015231 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 2015231 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
 sdb: sdb1
sd 5:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
Adding 923696k swap on /dev/sda7.  Priority:-1 extents:1 across:923696k
EXT3 FS on sda6, internal journal
loop: loaded (max 8 devices)
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177
[drm] Initialized i915 1.5.0 20060119 on minor 0
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will b e case sensitive!

Budu se modlit k tučnákovy za toho kdo mi poradí proč mi to na notebooku nefunguje.

Předem díky za rady a doufám že těch informací není moc

P.S.-o problémech s nejnovějším jádrem a síťovým modulem e1000 vím, možná to má něco společného?? nevím