Administrace komentářů

Ahoj ke konecnemu doladeni Gentoo potrebuji doresit nasledujici problem. Mam kernel 2.6.3 a gentoo 2004 Vse jede krasne -- super distribuce Vse jede na notebooku HP Omnibook 6000

Mam k nemu pripojenou USB mys Logitech pred suspendem PC pomoci APM zaklopenim obrazovky, nebo stiskem tlacitka pod displayem .... jede krasne .. .. nainstaloval jsem hot-plug ... .. emerge hotplug .... ten zaktivuje pri startu tyto moduly (pro usb)

lsmod:
Module                  Size  Used by
floppy                 60500  0
orinoco_cs              9192  1
orinoco                44364  1 orinoco_cs
hermes                  8512  2 orinoco_cs,orinoco
hid                    33856  0
uhci_hcd               32844  0
snd_maestro3           24996  2
snd_ac97_codec         64068  1 snd_maestro3
snd_pcm_oss            55652  0
snd_pcm               102852  3 snd_maestro3,snd_pcm_oss
snd_page_alloc         12420  1 snd_pcm
snd_timer              26884  1 snd_pcm
snd_mixer_oss          20896  1 snd_pcm_oss
usbcore               115484  4 hid,uhci_hcd
evdev                  10304  1

a takto vypada dmesg pred suspendem

drivers/usb/core/usb.c: registered new driver usbfs
drivers/usb/core/usb.c: registered new driver hub
devfs_mk_cdev: could not append to parent for snd/timer
PCI: Found IRQ 5 for device 0000:00:0d.0
PCI: Sharing IRQ 5 with 0000:00:0d.1
devfs_mk_cdev: could not append to parent for snd/pcmC0D0p
devfs_mk_cdev: could not append to parent for snd/pcmC0D0c
drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1
PCI: Found IRQ 10 for device 0000:00:07.2
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: irq 10, io base 00001020
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
drivers/usb/host/uhci-hcd.c: detected 2 ports
uhci_hcd 0000:00:07.2: root hub device address 1
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
drivers/usb/core/message.c: USB device number 1 default language ID 0x409
usb usb1: Product: UHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.3 uhci_hcd
usb usb1: SerialNumber: 0000:00:07.2
drivers/usb/core/usb.c: usb_hotplug
usb usb1: registering 1-0:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: ganged power switching
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: Port indicators are not supported
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: hub controller current requirement: 0mA
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
hub 1-0:1.0: enabling power on all ports
hub 1-0:1.0: port 1, status 301, change 1, 1.5 Mb/s
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
usb 1-1: new low speed USB device using address 2
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0
drivers/usb/core/message.c: USB device number 2 default language ID 0x409
usb 1-1: Product: USB-PS/2 Optical Mouse
usb 1-1: Manufacturer: Logitech
drivers/usb/core/usb.c: usb_hotplug
usb 1-1: registering 1-1:1.0 (config #1, interface 0)
drivers/usb/core/usb.c: usb_hotplug
drivers/usb/core/usb.c: registered new driver hiddev
hid 1-1:1.0: usb_probe_interface
hid 1-1:1.0: usb_probe_interface - got id
input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:00:07.2-1
drivers/usb/core/usb.c: registered new driver hid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver

potom notebook suspenduji --> a po probuzeni dam dmesg

od doby tesne pred probuzenim a po probuzeni:

hdc: start_power_step(step: 0)
hdc: completing PM request, suspend
hda: start_power_step(step: 0)
hda: start_power_step(step: 1)
hda: complete_power_step(step: 1, stat: 50, err: 0)
hda: completing PM request, suspend
orinoco_lock() called with hw_unavailable (dev=cee11800)
uhci_hcd 0000:00:07.2: suspend D4 --> D3
drivers/usb/host/uhci-hcd.c: 1020: suspend_hc
Synaptics driver lost sync at byte 1
Synaptics driver lost sync at byte 1
Synaptics driver lost sync at byte 1
Synaptics driver lost sync at byte 1
Synaptics driver lost sync at byte 1
Synaptics driver lost sync at byte 1
uhci_hcd 0000:00:07.2: resume from state D4
drivers/usb/host/uhci-hcd.c: 1020: wakeup_hc
Synaptics driver resynced.
hub 1-0:1.0: port 1, status 301, change 3, 1.5 Mb/s
usb 1-1: USB disconnect, address 2
usb 1-1: usb_disable_device nuking all URBs
usb 1-1: unregistering interface 1-1:1.0
usb 1-1: hcd_unlink_urb cf359780 fail -22
usb 1-1: hcd_unlink_urb cf359720 fail -22
eth0: New link status: Connected (0001)
hda: Wakeup request inited, waiting for !BSY...
hda: start_power_step(step: 1000)
blk: queue c1383200, I/O limit 4095Mb (mask 0xffffffff)
hda: completing PM request, resume
hdc: Wakeup request inited, waiting for !BSY...
hdc: start_power_step(step: 1000)
hdc: completing PM request, resume
drivers/usb/core/usb.c: usb_hotplug
usb 1-1: unregistering device
drivers/usb/core/usb.c: usb_hotplug
updfstab: numerical sysctl 1 23 is obsolete.
floppy0: unexpected interrupt
floppy0: sensei repl[0]=c0 repl[1]=0
floppy0: sensei repl[0]=c1 repl[1]=0
floppy0: sensei repl[0]=c2 repl[1]=0
floppy0: sensei repl[0]=c3 repl[1]=0
hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
usb 1-1: new low speed USB device using address 3
usb 1-1: control timeout on ep0out

mys nenabehne, ale moduly zustanou naloadovane..

root@jur jirka # lsmod
Module                  Size  Used by
floppy                 60500  0
orinoco_cs              9192  1
orinoco                44364  1 orinoco_cs
hermes                  8512  2 orinoco_cs,orinoco
hid                    33856  0
uhci_hcd               32844  0
snd_maestro3           24996  1
snd_ac97_codec         64068  1 snd_maestro3
snd_pcm_oss            55652  0
snd_pcm               102852  2 snd_maestro3,snd_pcm_oss
snd_page_alloc         12420  1 snd_pcm
snd_timer              26884  1 snd_pcm
snd_mixer_oss          20896  1 snd_pcm_oss
usbcore               115484  4 hid,uhci_hcd
evdev                  10304  1

Touchpad -- funguje

kdyz chci dat modprobe -r uhci_hcd, tak konzole vytuhne ... ... muzu mackat enter kolikrat chci a porad to sjizdi niz a niz a prikaz se neprovede

root@jur jirka # modprobe -r uhci_hcd

ani control + c nepomuze

kdyz si pustim druhou konzoli a dam dmesg, tak tam pribylo

uhci_hcd 0000:00:07.2: remove, state 1
uhci_hcd 0000:00:07.2: roothub graceful disconnect
usb usb1: USB disconnect, address 1
usb usb1: usb_disable_device nuking all URBs
uhci_hcd 0000:00:07.2: shutdown urb cf359840 pipe 40408180 ep1in-intr
usb usb1: unregistering interface 1-0:1.0

ale na konzoli jedna je porad vytuhnutej prikaz modprobe -r

... toto jsem provadel jak v Xkach, tak i v textu

vzdy stejnej vysledek

... prosim poradte mi co s tim

Diky moc