[ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 2.6.29-gentoo-r5 (root@bisan) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #3 SMP Wed Jul 8 03:44:44 Local time zone must be set--see zic m [ 0.000000] KERNEL supported cpus: [ 0.000000] Intel GenuineIntel [ 0.000000] AMD AuthenticAMD [ 0.000000] NSC Geode by NSC [ 0.000000] Cyrix CyrixInstead [ 0.000000] Centaur CentaurHauls [ 0.000000] Transmeta GenuineTMx86 [ 0.000000] Transmeta TransmetaCPU [ 0.000000] UMC UMC UMC UMC [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f400 (usable) [ 0.000000] BIOS-e820: 000000000009f400 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000d2000 - 00000000000d4000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 00000000bd6b3000 (usable) [ 0.000000] BIOS-e820: 00000000bd6b3000 - 00000000bd6b9000 (reserved) [ 0.000000] BIOS-e820: 00000000bd6b9000 - 00000000bd7b2000 (usable) [ 0.000000] BIOS-e820: 00000000bd7b2000 - 00000000bd80f000 (reserved) [ 0.000000] BIOS-e820: 00000000bd80f000 - 00000000bd907000 (usable) [ 0.000000] BIOS-e820: 00000000bd907000 - 00000000bdb0f000 (reserved) [ 0.000000] BIOS-e820: 00000000bdb0f000 - 00000000bdb18000 (usable) [ 0.000000] BIOS-e820: 00000000bdb18000 - 00000000bdb1f000 (reserved) [ 0.000000] BIOS-e820: 00000000bdb1f000 - 00000000bdb63000 (usable) [ 0.000000] BIOS-e820: 00000000bdb63000 - 00000000bdb9f000 (ACPI NVS) [ 0.000000] BIOS-e820: 00000000bdb9f000 - 00000000bdc00000 (ACPI data) [ 0.000000] BIOS-e820: 00000000bdc00000 - 00000000bde00000 (reserved) [ 0.000000] BIOS-e820: 00000000be000000 - 00000000c0000000 (reserved) [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved) [ 0.000000] BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved) [ 0.000000] BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved) [ 0.000000] BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved) [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved) [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) [ 0.000000] BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved) [ 0.000000] DMI present. [ 0.000000] last_pfn = 0xbdb63 max_arch_pfn = 0x100000 [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 [ 0.000000] kernel direct mapping tables up to 373fe000 @ 7000-d000 [ 0.000000] ACPI: RSDP 000F7190, 0024 (r2 LENOVO) [ 0.000000] ACPI: XSDT BDBF6067, 006C (r1 LENOVO TP-6G 0 LTP 0) [ 0.000000] ACPI: FACP BDBE8000, 00F4 (r3 LENOVO TP-6G 1 ALAN 1) [ 0.000000] FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4) [ 0.000000] ACPI: DSDT BDBE9000, 6B23 (r2 LENOVO TP-6G 1 INTL 20050624) [ 0.000000] ACPI: FACS BDB9EFC0, 0040 [ 0.000000] ACPI: HPET BDBFCD86, 0038 (r1 LENOVO TP-6G 1 LOHR 5A) [ 0.000000] ACPI: MCFG BDBFCDBE, 003C (r1 LENOVO TP-6G 1 LOHR 5A) [ 0.000000] ACPI: SLIC BDBFCDFA, 0176 (r1 LENOVO TP-6G 1 TBD 1) [ 0.000000] ACPI: APIC BDBFCF70, 0068 (r1 PTLTD APIC 0 LTP 0) [ 0.000000] ACPI: BOOT BDBFCFD8, 0028 (r1 PTLTD $SBFTBL$ 0 LTP 1) [ 0.000000] ACPI: SSDT BDBE7000, 0655 (r1 PmRef CpuPm 3000 INTL 20050624) [ 0.000000] ACPI: SSDT BDBE6000, 0259 (r1 PmRef Cpu0Tst 3000 INTL 20050624) [ 0.000000] ACPI: SSDT BDBE5000, 020F (r1 PmRef ApTst 3000 INTL 20050624) [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] 2151MB HIGHMEM available. [ 0.000000] 883MB LOWMEM available. [ 0.000000] mapped low ram: 0 - 373fe000 [ 0.000000] low ram: 00000000 - 373fe000 [ 0.000000] bootmap 00008000 - 0000ee80 [ 0.000000] (8 early reservations) ==> bootmem [0000000000 - 00373fe000] [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] [ 0.000000] #1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000] [ 0.000000] #2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000] [ 0.000000] #3 [0001000000 - 00017dd9f4] TEXT DATA BSS ==> [0001000000 - 00017dd9f4] [ 0.000000] #4 [00017de000 - 00017e6000] INIT_PG_TABLE ==> [00017de000 - 00017e6000] [ 0.000000] #5 [000009f400 - 0000100000] BIOS reserved ==> [000009f400 - 0000100000] [ 0.000000] #6 [0000007000 - 0000008000] PGTABLE ==> [0000007000 - 0000008000] [ 0.000000] #7 [0000008000 - 000000f000] BOOTMAP ==> [0000008000 - 000000f000] [ 0.000000] found SMP MP-table at [c00f7230] 000f7230 [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0x00000000 -> 0x00001000 [ 0.000000] Normal 0x00001000 -> 0x000373fe [ 0.000000] HighMem 0x000373fe -> 0x000bdb63 [ 0.000000] Movable zone start PFN for each node [ 0.000000] early_node_map[6] active PFN ranges [ 0.000000] 0: 0x00000000 -> 0x0000009f [ 0.000000] 0: 0x00000100 -> 0x000bd6b3 [ 0.000000] 0: 0x000bd6b9 -> 0x000bd7b2 [ 0.000000] 0: 0x000bd80f -> 0x000bd907 [ 0.000000] 0: 0x000bdb0f -> 0x000bdb18 [ 0.000000] 0: 0x000bdb1f -> 0x000bdb63 [ 0.000000] On node 0 totalpages: 776336 [ 0.000000] free_area_init_node: node 0, pgdat c166f480, node_mem_map c17e6000 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 3967 pages, LIFO batch:0 [ 0.000000] Normal zone: 1736 pages used for memmap [ 0.000000] Normal zone: 220470 pages, LIFO batch:31 [ 0.000000] HighMem zone: 4303 pages used for memmap [ 0.000000] HighMem zone: 545828 pages, LIFO batch:31 [ 0.000000] ACPI: PM-Timer IO Port: 0x408 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: IRQ0 used by override. [ 0.000000] ACPI: IRQ2 used by override. [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs [ 0.000000] nr_irqs_gsi: 24 [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000d2000 [ 0.000000] PM: Registered nosave memory: 00000000000d2000 - 00000000000d4000 [ 0.000000] PM: Registered nosave memory: 00000000000d4000 - 00000000000dc000 [ 0.000000] PM: Registered nosave memory: 00000000000dc000 - 0000000000100000 [ 0.000000] Allocating PCI resources starting at c2000000 (gap: c0000000:20000000) [ 0.000000] NR_CPUS:64 nr_cpumask_bits:64 nr_cpu_ids:2 nr_node_ids:1 [ 0.000000] PERCPU: Allocating 45056 bytes of per cpu data [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 770265 [ 0.000000] Kernel command line: real_root=/dev/sda4 video=uvesafb:ywrap,mtrr:3,1280x800-32@70 [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Extended CMOS year: 2000 [ 0.000000] Fast TSC calibration using PIT [ 0.000000] Detected 2160.974 MHz processor. [ 0.000999] Console: colour VGA+ 80x25 [ 0.000999] console [tty0] enabled [ 0.000999] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000999] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000999] Memory: 3071140k/3108236k available (4261k kernel code, 33420k reserved, 2728k data, 376k init, 2200524k highmem) [ 0.000999] virtual kernel memory layout: [ 0.000999] fixmap : 0xffc79000 - 0xfffff000 (3608 kB) [ 0.000999] pkmap : 0xff400000 - 0xff800000 (4096 kB) [ 0.000999] vmalloc : 0xf7bfe000 - 0xff3fe000 ( 120 MB) [ 0.000999] lowmem : 0xc0000000 - 0xf73fe000 ( 883 MB) [ 0.000999] .init : 0xc16da000 - 0xc1738000 ( 376 kB) [ 0.000999] .data : 0xc1429502 - 0xc16d3598 (2728 kB) [ 0.000999] .text : 0xc1000000 - 0xc1429502 (4261 kB) [ 0.000999] Checking if this processor honours the WP bit even in supervisor mode...Ok. [ 0.000999] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000999] hpet clockevent registered [ 0.000999] HPET: 4 timers in total, 0 timers will be used for per-cpu timer [ 0.000999] Calibrating delay loop (skipped), value calculated using timer frequency.. 4321.94 BogoMIPS (lpj=2160974) [ 0.000999] Security Framework initialized [ 0.000999] SELinux: Initializing. [ 0.000999] SELinux: Starting in permissive mode [ 0.000999] Mount-cache hash table entries: 512 [ 0.000999] Initializing cgroup subsys ns [ 0.000999] Initializing cgroup subsys cpuacct [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.001008] CPU: L2 cache: 1024K [ 0.001091] CPU: Physical Processor ID: 0 [ 0.001176] CPU: Processor Core ID: 0 [ 0.001261] using mwait in idle threads. [ 0.001353] Checking 'hlt' instruction... OK. [ 0.005456] ACPI: Core revision 20081204 [ 0.017464] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 [ 0.027563] CPU0: Intel(R) Pentium(R) Dual CPU T3400 @ 2.16GHz stepping 0d [ 0.027995] Booting processor 1 APIC 0x1 ip 0x6000 [ 0.000999] Initializing CPU#1 [ 0.000999] Calibrating delay using timer specific routine.. 4322.27 BogoMIPS (lpj=2161139) [ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K [ 0.000999] CPU: L2 cache: 1024K [ 0.000999] CPU: Physical Processor ID: 0 [ 0.000999] CPU: Processor Core ID: 1 [ 0.000999] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 [ 0.099218] CPU1: Intel(R) Pentium(R) Dual CPU T3400 @ 2.16GHz stepping 0d [ 0.099992] checking TSC synchronization [CPU#0 -> CPU#1]: passed. [ 0.101068] Brought up 2 CPUs [ 0.101152] Total of 2 processors activated (8644.22 BogoMIPS). [ 0.101325] khelper used greatest stack depth: 7092 bytes left [ 0.101325] net_namespace: 996 bytes [ 0.102136] Time: 3:50:04 Date: 07/08/09 [ 0.102245] NET: Registered protocol family 16 [ 0.102345] ACPI: bus type pci registered [ 0.102345] PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 255 [ 0.102987] PCI: MCFG area at e0000000 reserved in E820 [ 0.103072] PCI: Using MMCONFIG for extended config space [ 0.103933] PCI: Using configuration type 1 for base access [ 0.109205] bio: create slab at 0 [ 0.110642] ACPI: EC: Look up EC in DSDT [ 0.114121] ACPI: BIOS _OSI(Linux) query ignored [ 0.115160] ACPI: Interpreter enabled [ 0.115160] ACPI: (supports S0 S3 S4 S5) [ 0.115160] ACPI: Using IOAPIC for interrupt routing [ 0.161121] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62 [ 0.161175] ACPI: EC: driver started in poll mode [ 0.161288] ACPI: No dock devices found. [ 0.162016] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 0.162137] pci 0000:00:02.0: reg 10 64bit mmio: [0xf4000000-0xf43fffff] [ 0.162137] pci 0000:00:02.0: reg 18 64bit mmio: [0xd0000000-0xdfffffff] [ 0.162137] pci 0000:00:02.0: reg 20 io port: [0x1800-0x1807] [ 0.162137] pci 0000:00:02.1: reg 10 64bit mmio: [0xf4400000-0xf44fffff] [ 0.162216] pci 0000:00:1a.0: reg 20 io port: [0x1820-0x183f] [ 0.162313] pci 0000:00:1a.1: reg 20 io port: [0x1840-0x185f] [ 0.162409] pci 0000:00:1a.2: reg 20 io port: [0x1860-0x187f] [ 0.162495] pci 0000:00:1a.7: reg 10 32bit mmio: [0xf4a04800-0xf4a04bff] [ 0.162591] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold [ 0.162682] pci 0000:00:1a.7: PME# disabled [ 0.162986] pci 0000:00:1b.0: reg 10 64bit mmio: [0xf4a00000-0xf4a03fff] [ 0.163061] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold [ 0.163152] pci 0000:00:1b.0: PME# disabled [ 0.163320] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold [ 0.163411] pci 0000:00:1c.0: PME# disabled [ 0.163583] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold [ 0.163674] pci 0000:00:1c.1: PME# disabled [ 0.163844] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold [ 0.163934] pci 0000:00:1c.2: PME# disabled [ 0.164064] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold [ 0.164155] pci 0000:00:1c.3: PME# disabled [ 0.164328] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold [ 0.164418] pci 0000:00:1c.5: PME# disabled [ 0.164567] pci 0000:00:1d.0: reg 20 io port: [0x1880-0x189f] [ 0.164663] pci 0000:00:1d.1: reg 20 io port: [0x18a0-0x18bf] [ 0.164760] pci 0000:00:1d.2: reg 20 io port: [0x18c0-0x18df] [ 0.164845] pci 0000:00:1d.7: reg 10 32bit mmio: [0xf4a04c00-0xf4a04fff] [ 0.164992] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold [ 0.165082] pci 0000:00:1d.7: PME# disabled [ 0.165397] pci 0000:00:1f.2: reg 10 io port: [0x1818-0x181f] [ 0.165405] pci 0000:00:1f.2: reg 14 io port: [0x180c-0x180f] [ 0.165413] pci 0000:00:1f.2: reg 18 io port: [0x1810-0x1817] [ 0.165420] pci 0000:00:1f.2: reg 1c io port: [0x1808-0x180b] [ 0.165428] pci 0000:00:1f.2: reg 20 io port: [0x18e0-0x18ff] [ 0.165436] pci 0000:00:1f.2: reg 24 32bit mmio: [0xf4a04000-0xf4a047ff] [ 0.165516] pci 0000:00:1f.2: PME# supported from D3hot [ 0.165605] pci 0000:00:1f.2: PME# disabled [ 0.165727] pci 0000:00:1f.3: reg 10 64bit mmio: [0x000000-0x0000ff] [ 0.165747] pci 0000:00:1f.3: reg 20 io port: [0x1c00-0x1c1f] [ 0.165834] pci 0000:02:00.0: reg 10 32bit mmio: [0xf4500000-0xf45000ff] [ 0.165913] pci 0000:02:00.0: reg 30 32bit mmio: [0x000000-0x00ffff] [ 0.166079] pci 0000:02:00.2: reg 10 32bit mmio: [0xf4500400-0xf45004ff] [ 0.166313] pci 0000:02:00.3: reg 10 32bit mmio: [0xf4500800-0xf45008ff] [ 0.166562] pci 0000:00:1c.0: bridge 32bit mmio: [0xf4500000-0xf45fffff] [ 0.166790] pci 0000:04:00.0: reg 10 64bit mmio: [0xf4700000-0xf4703fff] [ 0.167063] pci 0000:04:00.0: supports D1 D2 [ 0.167065] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold [ 0.167197] pci 0000:04:00.0: PME# disabled [ 0.167435] pci 0000:00:1c.2: bridge 32bit mmio: [0xf4700000-0xf47fffff] [ 0.167499] pci 0000:00:1c.3: bridge io port: [0x2000-0x2fff] [ 0.167504] pci 0000:00:1c.3: bridge 32bit mmio: [0xf0000000-0xf3ffffff] [ 0.167513] pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf6000000-0xf7ffffff] [ 0.167678] pci 0000:07:00.0: reg 10 64bit mmio: [0xf4600000-0xf460ffff] [ 0.167980] pci 0000:07:00.0: PME# supported from D3hot D3cold [ 0.168109] pci 0000:07:00.0: PME# disabled [ 0.168318] pci 0000:00:1c.5: bridge 32bit mmio: [0xf4600000-0xf46fffff] [ 0.168393] pci 0000:00:1e.0: transparent bridge [ 0.168527] pci_bus 0000:00: on NUMA node 0 [ 0.168535] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 0.168688] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] [ 0.168775] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT] [ 0.168857] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT] [ 0.168925] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT] [ 0.169001] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT] [ 0.169071] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT] [ 0.181079] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 *5 6 7 10 12 14 15) [ 0.182053] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 0.182762] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 *3 4 5 6 7 10 12 14 15) [ 0.183463] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10 [ 0.184247] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 *7 10 12 14 15) [ 0.184983] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15) [ 0.185688] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15) [ 0.186378] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 *4 5 6 7 11 12 14 15) [ 0.187160] SCSI subsystem initialized [ 0.187160] libata version 3.00 loaded. [ 0.187160] usbcore: registered new interface driver usbfs [ 0.187977] usbcore: registered new interface driver hub [ 0.188076] usbcore: registered new device driver usb [ 0.188156] PCI: Using ACPI for IRQ routing [ 0.197005] cfg80211: Using static regulatory domain info [ 0.197061] cfg80211: Regulatory domain: US [ 0.197145] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 0.197271] (2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) [ 0.197360] (5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.197449] (5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.197537] (5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.197627] (5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) [ 0.197715] (5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) [ 0.197805] cfg80211: Calling CRDA for country: US [ 0.197904] NetLabel: Initializing [ 0.197971] NetLabel: domain hash size = 128 [ 0.198055] NetLabel: protocols = UNLABELED CIPSOv4 [ 0.198153] NetLabel: unlabeled traffic allowed by default [ 0.198255] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0 [ 0.198282] hpet0: 4 comparators, 64-bit 14.318180 MHz counter [ 0.204975] pnp: PnP ACPI init [ 0.205064] ACPI: bus type pnp registered [ 0.217001] ACPI: EC: non-query interrupt received, switching to interrupt mode [ 0.227019] pnp: PnP ACPI: found 10 devices [ 0.227105] ACPI: ACPI bus type pnp unregistered [ 0.227200] system 00:03: iomem range 0xfed00000-0xfed003ff has been reserved [ 0.227293] system 00:05: ioport range 0x680-0x69f has been reserved [ 0.227383] system 00:05: ioport range 0xffff-0xffff has been reserved [ 0.227472] system 00:05: ioport range 0xffff-0xffff has been reserved [ 0.227560] system 00:05: ioport range 0xffff-0xffff has been reserved [ 0.227648] system 00:05: ioport range 0x400-0x47f has been reserved [ 0.227737] system 00:05: ioport range 0x480-0x48f has been reserved [ 0.227826] system 00:05: ioport range 0x1180-0x11ff has been reserved [ 0.227915] system 00:05: ioport range 0x164e-0x164f has been reserved [ 0.228008] system 00:05: ioport range 0xfe00-0xfe00 has been reserved [ 0.228097] system 00:05: ioport range 0xff00-0xff7f has been reserved [ 0.228189] system 00:09: iomem range 0xfed1c000-0xfed1ffff has been reserved [ 0.228279] system 00:09: iomem range 0xfed10000-0xfed13fff has been reserved [ 0.228370] system 00:09: iomem range 0xfed18000-0xfed18fff has been reserved [ 0.228459] system 00:09: iomem range 0xfed19000-0xfed19fff has been reserved [ 0.228548] system 00:09: iomem range 0xe0000000-0xefffffff has been reserved [ 0.228638] system 00:09: iomem range 0xfed20000-0xfed3ffff has been reserved [ 0.228728] system 00:09: iomem range 0xfed40000-0xfed44fff has been reserved [ 0.228818] system 00:09: iomem range 0xfed45000-0xfed8ffff has been reserved [ 0.263654] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02 [ 0.263741] pci 0000:00:1c.0: IO window: disabled [ 0.263831] pci 0000:00:1c.0: MEM window: 0xf4500000-0xf45fffff [ 0.263922] pci 0000:00:1c.0: PREFETCH window: 0x000000c2000000-0x000000c20fffff [ 0.264057] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03 [ 0.264143] pci 0000:00:1c.1: IO window: disabled [ 0.264233] pci 0000:00:1c.1: MEM window: disabled [ 0.264322] pci 0000:00:1c.1: PREFETCH window: disabled [ 0.264413] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04 [ 0.264499] pci 0000:00:1c.2: IO window: disabled [ 0.264591] pci 0000:00:1c.2: MEM window: 0xf4700000-0xf47fffff [ 0.264681] pci 0000:00:1c.2: PREFETCH window: disabled [ 0.264772] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:05 [ 0.264860] pci 0000:00:1c.3: IO window: 0x2000-0x2fff [ 0.264951] pci 0000:00:1c.3: MEM window: 0xf0000000-0xf3ffffff [ 0.265045] pci 0000:00:1c.3: PREFETCH window: 0x000000f6000000-0x000000f7ffffff [ 0.265177] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:07 [ 0.265265] pci 0000:00:1c.5: IO window: disabled [ 0.265355] pci 0000:00:1c.5: MEM window: 0xf4600000-0xf46fffff [ 0.265446] pci 0000:00:1c.5: PREFETCH window: disabled [ 0.265538] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:08 [ 0.265625] pci 0000:00:1e.0: IO window: disabled [ 0.265715] pci 0000:00:1e.0: MEM window: disabled [ 0.265804] pci 0000:00:1e.0: PREFETCH window: disabled [ 0.265908] pci 0000:00:1c.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 0.266004] pci 0000:00:1c.0: setting latency timer to 64 [ 0.266014] pci 0000:00:1c.1: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 0.266104] pci 0000:00:1c.1: setting latency timer to 64 [ 0.266114] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 0.266206] pci 0000:00:1c.2: setting latency timer to 64 [ 0.266216] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 [ 0.266308] pci 0000:00:1c.3: setting latency timer to 64 [ 0.266317] pci 0000:00:1c.5: PCI INT B -> GSI 16 (level, low) -> IRQ 16 [ 0.266408] pci 0000:00:1c.5: setting latency timer to 64 [ 0.266416] pci 0000:00:1e.0: setting latency timer to 64 [ 0.266420] pci_bus 0000:00: resource 0 io: [0x00-0xffff] [ 0.266422] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff] [ 0.266424] pci_bus 0000:02: resource 0 mem: [0x0-0x0] [ 0.266426] pci_bus 0000:02: resource 1 mem: [0xf4500000-0xf45fffff] [ 0.266428] pci_bus 0000:02: resource 2 mem: [0xc2000000-0xc20fffff] [ 0.266430] pci_bus 0000:02: resource 3 mem: [0x0-0x0] [ 0.266432] pci_bus 0000:03: resource 0 mem: [0x0-0x0] [ 0.266434] pci_bus 0000:03: resource 1 mem: [0x0-0x0] [ 0.266436] pci_bus 0000:03: resource 2 mem: [0x0-0x0] [ 0.266438] pci_bus 0000:03: resource 3 mem: [0x0-0x0] [ 0.266440] pci_bus 0000:04: resource 0 mem: [0x0-0x0] [ 0.266441] pci_bus 0000:04: resource 1 mem: [0xf4700000-0xf47fffff] [ 0.266443] pci_bus 0000:04: resource 2 mem: [0x0-0x0] [ 0.266445] pci_bus 0000:04: resource 3 mem: [0x0-0x0] [ 0.266447] pci_bus 0000:05: resource 0 io: [0x2000-0x2fff] [ 0.266449] pci_bus 0000:05: resource 1 mem: [0xf0000000-0xf3ffffff] [ 0.266451] pci_bus 0000:05: resource 2 mem: [0xf6000000-0xf7ffffff] [ 0.266453] pci_bus 0000:05: resource 3 mem: [0x0-0x0] [ 0.266455] pci_bus 0000:07: resource 0 mem: [0x0-0x0] [ 0.266457] pci_bus 0000:07: resource 1 mem: [0xf4600000-0xf46fffff] [ 0.266459] pci_bus 0000:07: resource 2 mem: [0x0-0x0] [ 0.266460] pci_bus 0000:07: resource 3 mem: [0x0-0x0] [ 0.266462] pci_bus 0000:08: resource 0 mem: [0x0-0x0] [ 0.266464] pci_bus 0000:08: resource 1 mem: [0x0-0x0] [ 0.266466] pci_bus 0000:08: resource 2 mem: [0x0-0x0] [ 0.266467] pci_bus 0000:08: resource 3 io: [0x00-0xffff] [ 0.266469] pci_bus 0000:08: resource 4 mem: [0x000000-0xffffffff] [ 0.266497] NET: Registered protocol family 2 [ 0.278025] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.278389] TCP established hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.278920] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 0.279329] TCP: Hash tables configured (established 131072 bind 65536) [ 0.279419] TCP reno registered [ 0.282081] NET: Registered protocol family 1 [ 0.282394] Simple Boot Flag at 0x36 set to 0x1 [ 0.283269] Microcode Update Driver: v2.00 , Peter Oruba [ 0.283693] audit: initializing netlink socket (disabled) [ 0.283795] type=2000 audit(1247025003.282:1): initialized [ 0.291578] highmem bounce pool size: 64 pages [ 0.291667] HugeTLB registered 4 MB page size, pre-allocated 0 pages [ 0.294417] VFS: Disk quotas dquot_6.5.2 [ 0.294587] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.295190] NTFS driver 2.1.29 [Flags: R/W DEBUG]. [ 0.295518] msgmni has been set to 1701 [ 0.295704] SELinux: Registering netfilter hooks [ 0.295833] cryptomgr_test used greatest stack depth: 6948 bytes left [ 0.296174] alg: No test for stdrng (krng) [ 0.296377] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) [ 0.296501] io scheduler noop registered [ 0.296588] io scheduler anticipatory registered [ 0.296673] io scheduler deadline registered [ 0.296766] io scheduler cfq registered (default) [ 0.296862] pci 0000:00:02.0: Boot video device [ 0.296870] pci 0000:00:1a.0: uhci_check_and_reset_hc: legsup = 0x3000 [ 0.296872] pci 0000:00:1a.0: Performing full reset [ 0.296891] pci 0000:00:1a.1: uhci_check_and_reset_hc: legsup = 0x2000 [ 0.296893] pci 0000:00:1a.1: Performing full reset [ 0.296911] pci 0000:00:1a.2: uhci_check_and_reset_hc: legsup = 0x2000 [ 0.296913] pci 0000:00:1a.2: Performing full reset [ 0.296966] pci 0000:00:1d.0: uhci_check_and_reset_hc: legsup = 0x2000 [ 0.296968] pci 0000:00:1d.0: Performing full reset [ 0.296986] pci 0000:00:1d.1: uhci_check_and_reset_hc: legsup = 0x2000 [ 0.296987] pci 0000:00:1d.1: Performing full reset [ 0.297006] pci 0000:00:1d.2: uhci_check_and_reset_hc: legsup = 0x2000 [ 0.297008] pci 0000:00:1d.2: Performing full reset [ 0.297161] pcieport-driver 0000:00:1c.0: setting latency timer to 64 [ 0.297292] pcieport-driver 0000:00:1c.0: irq 24 for MSI/MSI-X [ 0.297494] pcieport-driver 0000:00:1c.1: setting latency timer to 64 [ 0.297574] pcieport-driver 0000:00:1c.1: irq 25 for MSI/MSI-X [ 0.297753] pcieport-driver 0000:00:1c.2: setting latency timer to 64 [ 0.297833] pcieport-driver 0000:00:1c.2: irq 26 for MSI/MSI-X [ 0.298009] pcieport-driver 0000:00:1c.3: setting latency timer to 64 [ 0.298089] pcieport-driver 0000:00:1c.3: irq 27 for MSI/MSI-X [ 0.298281] pcieport-driver 0000:00:1c.5: setting latency timer to 64 [ 0.298361] pcieport-driver 0000:00:1c.5: irq 28 for MSI/MSI-X [ 0.298598] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 0.298687] ibmphpd: IBM Hot Plug PCI Controller Driver version: 0.6 [ 0.299239] pciehp: PCI Express Hot Plug Controller Driver version: 0.4 [ 0.302566] Non-volatile memory driver v1.3 [ 0.302780] Linux agpgart interface v0.103 [ 0.302878] agpgart-intel 0000:00:00.0: Intel Mobile Intel® GM45 Express Chipset [ 0.303467] agpgart-intel 0000:00:00.0: detected 32764K stolen memory [ 0.307496] agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000 [ 0.314048] ACPI: AC Adapter [ACAD] (on-line) [ 0.474193] ACPI: Battery Slot [BAT1] (battery present) [ 0.474516] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 [ 0.476992] ACPI: Power Button (FF) [PWRF] [ 0.477149] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1 [ 0.477331] ACPI: Lid Switch [LID0] [ 0.477482] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2 [ 0.481992] ACPI: Power Button (CM) [PWRB] [ 0.482681] ACPI: SSDT BDB1AC20, 0265 (r1 PmRef Cpu0Ist 3000 INTL 20050624) [ 0.483246] ACPI: SSDT BDB18620, 0549 (r1 PmRef Cpu0Cst 3001 INTL 20050624) [ 0.488796] Monitor-Mwait will be used to enter C-1 state [ 0.488802] Monitor-Mwait will be used to enter C-2 state [ 0.488861] ACPI: CPU0 (power states: C1[C1] C2[C2]) [ 0.489118] processor ACPI_CPU:00: registered as cooling_device0 [ 0.489208] ACPI: Processor [CPU0] (supports 8 throttling states) [ 0.489821] ACPI: SSDT BDB19CA0, 01CF (r1 PmRef ApIst 3000 INTL 20050624) [ 0.490390] ACPI: SSDT BDB19F20, 008D (r1 PmRef ApCst 3000 INTL 20050624) [ 0.500248] Switched to high resolution mode on CPU 1 [ 0.500277] Switched to high resolution mode on CPU 0 [ 0.502890] ACPI: CPU1 (power states: C1[C1] C2[C2]) [ 0.503151] processor ACPI_CPU:01: registered as cooling_device1 [ 0.504022] ACPI: Processor [CPU1] (supports 8 throttling states) [ 0.531797] ACPI: Invalid active0 threshold [ 0.531989] thermal LNXTHERM:01: registered as thermal_zone0 [ 0.545961] ACPI: Thermal Zone [TZ00] (54 C) [ 0.546146] [drm] Initialized drm 1.1.0 20060810 [ 0.546301] pci 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 0.546391] pci 0000:00:02.0: setting latency timer to 64 [ 0.548490] pci 0000:00:02.0: irq 29 for MSI/MSI-X [ 0.996292] allocated 1280x800 fb: 0x02020000, bo f6fd0120 [ 1.267326] [drm] LVDS-8: set mode 1280x800 c [ 2.039032] Console: switching to colour frame buffer device 160x50 [ 2.044264] fb0: inteldrmfb frame buffer device [ 2.044309] registered panic notifier [ 2.044348] [drm] Initialized i915 1.6.0 20080730 on minor 0 [ 2.044434] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 2.046562] brd: module loaded [ 2.047355] loop: module loaded [ 2.047387] Intel(R) PRO/1000 Network Driver - version 7.3.21-k3-NAPI [ 2.047440] Copyright (c) 1999-2006 Intel Corporation. [ 2.047546] e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k6 [ 2.047598] e1000e: Copyright (c) 1999-2008 Intel Corporation. [ 2.047760] e100: Intel(R) PRO/100 Network Driver, 3.5.23-k6-NAPI [ 2.047810] e100: Copyright(c) 1999-2006 Intel Corporation [ 2.047923] tg3.c:v3.97 (December 10, 2008) [ 2.048021] tg3 0000:07:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17 [ 2.048127] tg3 0000:07:00.0: setting latency timer to 64 [ 2.050364] tg3 0000:07:00.0: PME# disabled [ 2.131213] eth0: Tigon3 [partno(BCM95906) rev c002] (PCI Express) MAC address 00:23:5a:1a:00:10 [ 2.131292] eth0: attached PHY is 5906 (10/100Base-TX Ethernet) (WireSpeed[0]) [ 2.131365] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1] [ 2.131429] eth0: dma_rwctrl[76180000] dma_mask[64-bit] [ 2.131560] sky2 driver version 1.22 [ 2.131689] PPP generic driver version 2.4.2 [ 2.131949] Broadcom 43xx driver loaded [ Features: PLR, Firmware-ID: FW13 ] [ 2.132059] Broadcom 43xx-legacy driver loaded [ Features: PLRID, Firmware-ID: FW10 ] [ 2.132180] console [netcon0] enabled [ 2.133477] netconsole: network logging started [ 2.134934] input: Macintosh mouse button emulation as /devices/virtual/input/input3 [ 2.136513] Loading iSCSI transport class v2.0-870. [ 2.138082] Driver 'sd' needs updating - please use bus_type methods [ 2.139653] Driver 'sr' needs updating - please use bus_type methods [ 2.141357] ahci 0000:00:1f.2: version 3.0 [ 2.141369] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 2.143067] ahci 0000:00:1f.2: irq 30 for MSI/MSI-X [ 2.143113] ahci: SSS flag set, parallel bus scan disabled [ 2.144839] ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x3 impl SATA mode [ 2.146462] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems [ 2.148231] ahci 0000:00:1f.2: setting latency timer to 64 [ 2.148415] scsi0 : ahci [ 2.150371] scsi1 : ahci [ 2.152181] scsi2 : ahci [ 2.154049] scsi3 : ahci [ 2.155960] ata1: SATA max UDMA/133 abar m2048@0xf4a04000 port 0xf4a04100 irq 30 [ 2.157778] ata2: SATA max UDMA/133 abar m2048@0xf4a04000 port 0xf4a04180 irq 30 [ 2.159785] ata3: DUMMY [ 2.161709] ata4: DUMMY [ 2.468022] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [ 2.514565] ata1.00: ATA-8: WDC WD2500BEVT-88ZCT0, 11.01A11, max UDMA/133 [ 2.516452] ata1.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 31/32) [ 2.521375] ata1.00: configured for UDMA/133 [ 2.534097] scsi 0:0:0:0: Direct-Access ATA WDC WD2500BEVT-8 11.0 PQ: 0 ANSI: 5 [ 2.536307] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB) [ 2.538244] sd 0:0:0:0: [sda] Write Protect is off [ 2.540247] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.540272] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.542400] sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors: (250 GB/232 GiB) [ 2.544444] sd 0:0:0:0: [sda] Write Protect is off [ 2.546439] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 2.546462] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 2.548585] sda: sda1 sda2 sda3 sda4 [ 2.585281] sd 0:0:0:0: [sda] Attached SCSI disk [ 2.587267] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 2.894021] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 2.909608] ata2.00: ATAPI: Optiarc DVD RW AD-7580S, F806, max UDMA/100, ATAPI AN [ 2.925787] ata2.00: configured for UDMA/100 [ 2.940172] scsi 1:0:0:0: CD-ROM Optiarc DVD RW AD-7580S F806 PQ: 0 ANSI: 5 [ 2.947742] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 2.949831] Uniform CD-ROM driver Revision: 3.20 [ 2.951938] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 2.952026] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 2.954517] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.956546] ehci_hcd: block sizes: qh 128 qtd 96 itd 160 sitd 96 [ 2.956583] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 2.958766] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [ 2.958770] ehci_hcd 0000:00:1a.7: EHCI Host Controller [ 2.960812] drivers/usb/core/inode.c: creating file 'devices' [ 2.960816] drivers/usb/core/inode.c: creating file '001' [ 2.960869] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1 [ 2.962911] ehci_hcd 0000:00:1a.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 2.962915] ehci_hcd 0000:00:1a.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr [ 2.962935] ehci_hcd 0000:00:1a.7: reset command 080032 (park)=0 ithresh=8 Async Periodic period=1024 Reset HALT [ 2.966838] ehci_hcd 0000:00:1a.7: debug port 1 [ 2.968840] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported [ 2.968842] ehci_hcd 0000:00:1a.7: supports USB remote wakeup [ 2.968856] ehci_hcd 0000:00:1a.7: irq 20, io mem 0xf4a04800 [ 2.970840] ehci_hcd 0000:00:1a.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 2.974733] ehci_hcd 0000:00:1a.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN [ 2.980006] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 [ 2.981906] usb usb1: default language 0x0409 [ 2.981913] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 2.983974] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 2.985915] usb usb1: Product: EHCI Host Controller [ 2.987789] usb usb1: Manufacturer: Linux 2.6.29-gentoo-r5 ehci_hcd [ 2.989636] usb usb1: SerialNumber: 0000:00:1a.7 [ 2.991690] usb usb1: uevent [ 2.991727] usb usb1: usb_probe_device [ 2.991729] usb usb1: configuration #1 chosen from 1 choice [ 2.993696] usb usb1: adding 1-0:1.0 (config #1, interface 0) [ 2.993710] usb 1-0:1.0: uevent [ 2.993743] hub 1-0:1.0: usb_probe_interface [ 2.993745] hub 1-0:1.0: usb_probe_interface - got id [ 2.993747] hub 1-0:1.0: USB hub found [ 2.996306] hub 1-0:1.0: 6 ports detected [ 2.998116] hub 1-0:1.0: standalone hub [ 2.998118] hub 1-0:1.0: no power switching (usb 1.0) [ 2.998119] hub 1-0:1.0: individual port over-current protection [ 2.998121] hub 1-0:1.0: power on to power good time: 20ms [ 2.998125] hub 1-0:1.0: local power source is good [ 2.998127] hub 1-0:1.0: trying to enable port power on non-switchable hub [ 2.998235] drivers/usb/core/inode.c: creating file '001' [ 2.998307] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 3.000431] ehci_hcd 0000:00:1d.7: setting latency timer to 64 [ 3.000434] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 3.002313] drivers/usb/core/inode.c: creating file '002' [ 3.002363] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2 [ 3.004300] ehci_hcd 0000:00:1d.7: reset hcs_params 0x103206 dbg=1 cc=3 pcc=2 ordered !ppc ports=6 [ 3.004304] ehci_hcd 0000:00:1d.7: reset hcc_params 6871 thresh 7 uframes 1024 64 bit addr [ 3.004323] ehci_hcd 0000:00:1d.7: reset command 080032 (park)=0 ithresh=8 Async Periodic period=1024 Reset HALT [ 3.008226] ehci_hcd 0000:00:1d.7: debug port 1 [ 3.010193] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported [ 3.010195] ehci_hcd 0000:00:1d.7: supports USB remote wakeup [ 3.010207] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf4a04c00 [ 3.012297] ehci_hcd 0000:00:1d.7: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT [ 3.016183] ehci_hcd 0000:00:1d.7: init command 010001 (park)=0 ithresh=1 period=1024 RUN [ 3.022006] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 [ 3.024070] usb usb2: default language 0x0409 [ 3.024076] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 3.026124] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.028112] usb usb2: Product: EHCI Host Controller [ 3.030197] usb usb2: Manufacturer: Linux 2.6.29-gentoo-r5 ehci_hcd [ 3.032089] usb usb2: SerialNumber: 0000:00:1d.7 [ 3.034044] usb usb2: uevent [ 3.034079] usb usb2: usb_probe_device [ 3.034082] usb usb2: configuration #1 chosen from 1 choice [ 3.036029] usb usb2: adding 2-0:1.0 (config #1, interface 0) [ 3.036044] usb 2-0:1.0: uevent [ 3.036076] hub 2-0:1.0: usb_probe_interface [ 3.036078] hub 2-0:1.0: usb_probe_interface - got id [ 3.036080] hub 2-0:1.0: USB hub found [ 3.038637] hub 2-0:1.0: 6 ports detected [ 3.040496] hub 2-0:1.0: standalone hub [ 3.040497] hub 2-0:1.0: no power switching (usb 1.0) [ 3.040499] hub 2-0:1.0: individual port over-current protection [ 3.040501] hub 2-0:1.0: power on to power good time: 20ms [ 3.040505] hub 2-0:1.0: local power source is good [ 3.040507] hub 2-0:1.0: trying to enable port power on non-switchable hub [ 3.040578] drivers/usb/core/inode.c: creating file '001' [ 3.040666] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.042394] ohci_hcd: block sizes: ed 64 td 64 [ 3.042439] uhci_hcd: USB Universal Host Controller Interface driver [ 3.044371] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [ 3.046066] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [ 3.046070] uhci_hcd 0000:00:1a.0: UHCI Host Controller [ 3.047786] drivers/usb/core/inode.c: creating file '003' [ 3.047842] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3 [ 3.049702] uhci_hcd 0000:00:1a.0: detected 2 ports [ 3.051574] uhci_hcd 0000:00:1a.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 3.051576] uhci_hcd 0000:00:1a.0: Performing full reset [ 3.051604] uhci_hcd 0000:00:1a.0: irq 16, io base 0x00001820 [ 3.053396] usb usb3: default language 0x0409 [ 3.053403] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.055277] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.057082] usb usb3: Product: UHCI Host Controller [ 3.058861] usb usb3: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 3.060545] usb usb3: SerialNumber: 0000:00:1a.0 [ 3.062405] usb usb3: uevent [ 3.062443] usb usb3: usb_probe_device [ 3.062445] usb usb3: configuration #1 chosen from 1 choice [ 3.064120] usb usb3: adding 3-0:1.0 (config #1, interface 0) [ 3.064134] usb 3-0:1.0: uevent [ 3.064169] hub 3-0:1.0: usb_probe_interface [ 3.064171] hub 3-0:1.0: usb_probe_interface - got id [ 3.064173] hub 3-0:1.0: USB hub found [ 3.066265] hub 3-0:1.0: 2 ports detected [ 3.067881] hub 3-0:1.0: standalone hub [ 3.067883] hub 3-0:1.0: no power switching (usb 1.0) [ 3.067884] hub 3-0:1.0: individual port over-current protection [ 3.067886] hub 3-0:1.0: power on to power good time: 2ms [ 3.067890] hub 3-0:1.0: local power source is good [ 3.067892] hub 3-0:1.0: trying to enable port power on non-switchable hub [ 3.067947] drivers/usb/core/inode.c: creating file '001' [ 3.068024] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 [ 3.069835] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [ 3.069838] uhci_hcd 0000:00:1a.1: UHCI Host Controller [ 3.071438] drivers/usb/core/inode.c: creating file '004' [ 3.071491] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4 [ 3.073107] uhci_hcd 0000:00:1a.1: detected 2 ports [ 3.074930] uhci_hcd 0000:00:1a.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 3.074932] uhci_hcd 0000:00:1a.1: Performing full reset [ 3.074959] uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001840 [ 3.076793] usb usb4: default language 0x0409 [ 3.076800] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.078501] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.080315] usb usb4: Product: UHCI Host Controller [ 3.082005] usb usb4: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 3.083731] usb usb4: SerialNumber: 0000:00:1a.1 [ 3.085533] usb usb4: uevent [ 3.085568] usb usb4: usb_probe_device [ 3.085570] usb usb4: configuration #1 chosen from 1 choice [ 3.087299] usb usb4: adding 4-0:1.0 (config #1, interface 0) [ 3.087313] usb 4-0:1.0: uevent [ 3.087345] hub 4-0:1.0: usb_probe_interface [ 3.087347] hub 4-0:1.0: usb_probe_interface - got id [ 3.087349] hub 4-0:1.0: USB hub found [ 3.089635] hub 4-0:1.0: 2 ports detected [ 3.091330] hub 4-0:1.0: standalone hub [ 3.091332] hub 4-0:1.0: no power switching (usb 1.0) [ 3.091333] hub 4-0:1.0: individual port over-current protection [ 3.091335] hub 4-0:1.0: power on to power good time: 2ms [ 3.091339] hub 4-0:1.0: local power source is good [ 3.091341] hub 4-0:1.0: trying to enable port power on non-switchable hub [ 3.091405] drivers/usb/core/inode.c: creating file '001' [ 3.091481] uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 20 (level, low) -> IRQ 20 [ 3.093184] uhci_hcd 0000:00:1a.2: setting latency timer to 64 [ 3.093188] uhci_hcd 0000:00:1a.2: UHCI Host Controller [ 3.094812] drivers/usb/core/inode.c: creating file '005' [ 3.094861] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5 [ 3.096546] uhci_hcd 0000:00:1a.2: detected 2 ports [ 3.098208] uhci_hcd 0000:00:1a.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 3.098210] uhci_hcd 0000:00:1a.2: Performing full reset [ 3.098226] uhci_hcd 0000:00:1a.2: supports USB remote wakeup [ 3.098231] uhci_hcd 0000:00:1a.2: irq 20, io base 0x00001860 [ 3.100010] usb usb5: default language 0x0409 [ 3.100016] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.101810] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.103618] usb usb5: Product: UHCI Host Controller [ 3.105443] usb usb5: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 3.107082] usb usb5: SerialNumber: 0000:00:1a.2 [ 3.108947] usb usb5: uevent [ 3.108990] hub 1-0:1.0: state 7 ports 6 chg 0000 evt 0000 [ 3.108992] usb usb5: usb_probe_device [ 3.108993] usb usb5: configuration #1 chosen from 1 choice [ 3.109008] usb usb5: adding 5-0:1.0 (config #1, interface 0) [ 3.109024] usb 5-0:1.0: uevent [ 3.110801] hub 5-0:1.0: usb_probe_interface [ 3.110803] hub 5-0:1.0: usb_probe_interface - got id [ 3.110805] hub 5-0:1.0: USB hub found [ 3.113092] hub 5-0:1.0: 2 ports detected [ 3.114897] hub 5-0:1.0: standalone hub [ 3.114898] hub 5-0:1.0: no power switching (usb 1.0) [ 3.114900] hub 5-0:1.0: individual port over-current protection [ 3.114901] hub 5-0:1.0: power on to power good time: 2ms [ 3.114906] hub 5-0:1.0: local power source is good [ 3.114907] hub 5-0:1.0: trying to enable port power on non-switchable hub [ 3.114970] drivers/usb/core/inode.c: creating file '001' [ 3.115049] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 [ 3.116905] uhci_hcd 0000:00:1d.0: setting latency timer to 64 [ 3.116908] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 3.118574] drivers/usb/core/inode.c: creating file '006' [ 3.118632] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6 [ 3.120371] uhci_hcd 0000:00:1d.0: detected 2 ports [ 3.122111] uhci_hcd 0000:00:1d.0: uhci_check_and_reset_hc: cmd = 0x0000 [ 3.122113] uhci_hcd 0000:00:1d.0: Performing full reset [ 3.122129] uhci_hcd 0000:00:1d.0: supports USB remote wakeup [ 3.122134] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00001880 [ 3.123867] usb usb6: default language 0x0409 [ 3.123874] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.125696] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.127486] usb usb6: Product: UHCI Host Controller [ 3.129272] usb usb6: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 3.131136] usb usb6: SerialNumber: 0000:00:1d.0 [ 3.132951] usb usb6: uevent [ 3.132989] usb usb6: usb_probe_device [ 3.132992] usb usb6: configuration #1 chosen from 1 choice [ 3.134781] usb usb6: adding 6-0:1.0 (config #1, interface 0) [ 3.134795] usb 6-0:1.0: uevent [ 3.134831] hub 6-0:1.0: usb_probe_interface [ 3.134833] hub 6-0:1.0: usb_probe_interface - got id [ 3.134835] hub 6-0:1.0: USB hub found [ 3.137040] hub 6-0:1.0: 2 ports detected [ 3.138716] hub 6-0:1.0: standalone hub [ 3.138717] hub 6-0:1.0: no power switching (usb 1.0) [ 3.138719] hub 6-0:1.0: individual port over-current protection [ 3.138721] hub 6-0:1.0: power on to power good time: 2ms [ 3.138724] hub 6-0:1.0: local power source is good [ 3.138726] hub 6-0:1.0: trying to enable port power on non-switchable hub [ 3.138784] drivers/usb/core/inode.c: creating file '001' [ 3.138863] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 3.140636] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [ 3.140639] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 3.142397] ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001803 POWER sig=j CSC CONNECT [ 3.142400] hub 2-0:1.0: port 3: status 0501 change 0001 [ 3.142417] drivers/usb/core/inode.c: creating file '007' [ 3.142472] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7 [ 3.144124] uhci_hcd 0000:00:1d.1: detected 2 ports [ 3.145868] uhci_hcd 0000:00:1d.1: uhci_check_and_reset_hc: cmd = 0x0000 [ 3.145870] uhci_hcd 0000:00:1d.1: Performing full reset [ 3.145898] uhci_hcd 0000:00:1d.1: irq 19, io base 0x000018a0 [ 3.147673] usb usb7: default language 0x0409 [ 3.147679] usb usb7: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.149454] usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.151247] usb usb7: Product: UHCI Host Controller [ 3.153003] usb usb7: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 3.154682] usb usb7: SerialNumber: 0000:00:1d.1 [ 3.156443] usb usb7: uevent [ 3.156477] usb usb7: usb_probe_device [ 3.156479] usb usb7: configuration #1 chosen from 1 choice [ 3.158293] usb usb7: adding 7-0:1.0 (config #1, interface 0) [ 3.158307] usb 7-0:1.0: uevent [ 3.158341] hub 7-0:1.0: usb_probe_interface [ 3.158343] hub 7-0:1.0: usb_probe_interface - got id [ 3.158345] hub 7-0:1.0: USB hub found [ 3.160424] hub 7-0:1.0: 2 ports detected [ 3.162188] hub 7-0:1.0: standalone hub [ 3.162189] hub 7-0:1.0: no power switching (usb 1.0) [ 3.162191] hub 7-0:1.0: individual port over-current protection [ 3.162193] hub 7-0:1.0: power on to power good time: 2ms [ 3.162197] hub 7-0:1.0: local power source is good [ 3.162199] hub 7-0:1.0: trying to enable port power on non-switchable hub [ 3.162259] drivers/usb/core/inode.c: creating file '001' [ 3.162335] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [ 3.164021] uhci_hcd 0000:00:1d.2: setting latency timer to 64 [ 3.164025] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 3.165769] drivers/usb/core/inode.c: creating file '008' [ 3.165820] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8 [ 3.167556] uhci_hcd 0000:00:1d.2: detected 2 ports [ 3.169323] uhci_hcd 0000:00:1d.2: uhci_check_and_reset_hc: cmd = 0x0000 [ 3.169324] uhci_hcd 0000:00:1d.2: Performing full reset [ 3.169341] uhci_hcd 0000:00:1d.2: supports USB remote wakeup [ 3.169354] uhci_hcd 0000:00:1d.2: irq 18, io base 0x000018c0 [ 3.171055] usb usb8: default language 0x0409 [ 3.171061] usb usb8: New USB device found, idVendor=1d6b, idProduct=0001 [ 3.172844] usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 3.174676] usb usb8: Product: UHCI Host Controller [ 3.176340] usb usb8: Manufacturer: Linux 2.6.29-gentoo-r5 uhci_hcd [ 3.178070] usb usb8: SerialNumber: 0000:00:1d.2 [ 3.179817] usb usb8: uevent [ 3.179853] hub 3-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.179865] usb usb8: usb_probe_device [ 3.179867] usb usb8: configuration #1 chosen from 1 choice [ 3.181571] usb usb8: adding 8-0:1.0 (config #1, interface 0) [ 3.181587] usb 8-0:1.0: uevent [ 3.181625] hub 8-0:1.0: usb_probe_interface [ 3.181627] hub 8-0:1.0: usb_probe_interface - got id [ 3.181628] hub 8-0:1.0: USB hub found [ 3.183965] hub 8-0:1.0: 2 ports detected [ 3.185782] hub 8-0:1.0: standalone hub [ 3.185783] hub 8-0:1.0: no power switching (usb 1.0) [ 3.185785] hub 8-0:1.0: individual port over-current protection [ 3.185786] hub 8-0:1.0: power on to power good time: 2ms [ 3.185790] hub 8-0:1.0: local power source is good [ 3.185792] hub 8-0:1.0: trying to enable port power on non-switchable hub [ 3.185852] drivers/usb/core/inode.c: creating file '001' [ 3.186000] usbcore: registered new interface driver usblp [ 3.187729] Initializing USB Mass Storage driver... [ 3.189541] usbcore: registered new interface driver usb-storage [ 3.191333] USB Mass Storage support registered. [ 3.193155] hub 4-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.193163] usbcore: registered new interface driver libusual [ 3.195010] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 [ 3.214021] hub 5-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.232501] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 3.234314] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 3.238021] hub 6-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.240048] mice: PS/2 mouse device common for all mice [ 3.242009] hub 2-0:1.0: state 7 ports 6 chg 0008 evt 0000 [ 3.242015] hub 2-0:1.0: port 3, status 0501, change 0000, 480 Mb/s [ 3.258178] rtc_cmos 00:06: RTC can wake from S4 [ 3.259987] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0 [ 3.261844] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs [ 3.263691] uhci_hcd 0000:00:1d.1: port 1 portsc 0082,00 [ 3.263729] i801_smbus 0000:00:1f.3: PCI INT C -> GSI 19 (level, low) -> IRQ 19 [ 3.265594] ACPI: I/O resource 0000:00:1f.3 [0x1c00-0x1c1f] conflicts with ACPI region SMBI [0x1c00-0x1c0f] [ 3.267388] ACPI: Device needs an ACPI driver [ 3.269527] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com [ 3.271858] cpuidle: using governor ladder [ 3.274279] cpuidle: using governor menu [ 3.276127] No iBFT detected. [ 3.276253] Marking TSC unstable due to TSC halts in idle [ 3.280955] usbcore: registered new interface driver hiddev [ 3.282984] usbcore: registered new interface driver usbhid [ 3.284788] usbhid: v2.6:USB HID core driver [ 3.286798] Netfilter messages via NETLINK v0.30. [ 3.288519] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 3.290480] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4 [ 3.290689] ctnetlink v0.93: registering with nfnetlink. [ 3.291341] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.291371] TCP cubic registered [ 3.291372] Initializing XFRM netlink socket [ 3.291675] NET: Registered protocol family 10 [ 3.292716] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.292776] IPv6 over IPv4 tunneling driver [ 3.293442] NET: Registered protocol family 17 [ 3.308242] ehci_hcd 0000:00:1d.7: port 3 high speed [ 3.308247] ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT [ 3.308402] RPC: Registered udp transport module. [ 3.310411] RPC: Registered tcp transport module. [ 3.312262] lib80211: common routines for IEEE802.11 drivers [ 3.314028] lib80211_crypt: registered algorithm 'NULL' [ 3.314030] lib80211_crypt: registered algorithm 'WEP' [ 3.314032] lib80211_crypt: registered algorithm 'CCMP' [ 3.314034] lib80211_crypt: registered algorithm 'TKIP' [ 3.318311] Using IPI No-Shortcut mode [ 3.320238] registered taskstats version 1 [ 3.322220] Magic number: 1:708:815 [ 3.324023] uhci_hcd 0000:00:1a.2: hash matches [ 3.359315] usb 2-3: new high speed USB device using ehci_hcd and address 2 [ 3.412242] ehci_hcd 0000:00:1d.7: port 3 high speed [ 3.412246] ehci_hcd 0000:00:1d.7: GetStatus port 3 status 001005 POWER sig=se0 PE CONNECT [ 3.480645] usb 2-3: skipped 1 descriptor after configuration [ 3.480648] usb 2-3: skipped 5 descriptors after interface [ 3.480650] usb 2-3: skipped 1 descriptor after endpoint [ 3.480652] usb 2-3: skipped 7 descriptors after interface [ 3.480937] usb 2-3: default language 0x0409 [ 3.481520] usb 2-3: New USB device found, idVendor=090c, idProduct=3371 [ 3.483399] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.485283] usb 2-3: Product: Lenovo EasyCamera [ 3.487037] usb 2-3: Manufacturer: Image Processor [ 3.488790] usb 2-3: uevent [ 3.488865] usb 2-3: usb_probe_device [ 3.488868] usb 2-3: configuration #1 chosen from 1 choice [ 3.490893] usb 2-3: adding 2-3:1.0 (config #1, interface 0) [ 3.490913] usb 2-3:1.0: uevent [ 3.491127] usb 2-3: adding 2-3:1.1 (config #1, interface 1) [ 3.491146] usb 2-3:1.1: uevent [ 3.491243] drivers/usb/core/inode.c: creating file '002' [ 3.491355] hub 8-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.491359] hub 7-0:1.0: state 7 ports 2 chg 0000 evt 0000 [ 3.934495] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input5 [ 3.982261] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input6 [ 4.000320] Clocksource tsc unstable (delta = -361672655 ns) [ 4.032061] md: Waiting for all devices to be available before autodetect [ 4.033953] md: If you don't use raid, use raid=noautodetect [ 4.036185] md: Autodetecting RAID arrays. [ 4.038045] md: Scanned 0 and added 0 devices. [ 4.039826] md: autorun ... [ 4.041611] md: ... autorun DONE. [ 4.088105] ReiserFS: sda4: found reiserfs format "3.6" with standard journal [ 4.089960] ReiserFS: sda4: using ordered data mode [ 4.100640] ReiserFS: sda4: journal params: device sda4, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 4.104912] ReiserFS: sda4: checking transaction log (sda4) [ 4.106844] ReiserFS: sda4: journal-1153: found in header: first_unflushed_offset 2707, last_flushed_trans_id 12787 [ 4.118976] ReiserFS: sda4: journal-1206: Starting replay from offset 54924041783955, trans_id 4132938240 [ 4.118980] ReiserFS: sda4: journal-1299: Setting newest_mount_id to 70 [ 4.192529] ReiserFS: sda4: Using r5 hash to sort names [ 4.194568] VFS: Mounted root (reiserfs filesystem) readonly on device 8:4. [ 4.196833] Freeing unused kernel memory: 376k freed [ 4.198917] Write protecting the kernel text: 4264k [ 4.201025] Write protecting the kernel read-only data: 1920k [ 4.204042] usb usb3: suspend_rh (auto-stop) [ 4.204070] usb usb4: suspend_rh (auto-stop) [ 4.204096] usb usb5: suspend_rh (auto-stop) [ 4.204122] usb usb6: suspend_rh (auto-stop) [ 4.204149] usb usb8: suspend_rh (auto-stop) [ 4.235453] khelper used greatest stack depth: 6624 bytes left [ 4.455041] usb usb7: suspend_rh (auto-stop) [ 5.002023] init-early.sh used greatest stack depth: 5984 bytes left [ 5.701040] hub 1-0:1.0: hub_suspend [ 5.701048] usb usb1: bus auto-suspend [ 5.701051] ehci_hcd 0000:00:1a.7: suspend root hub [ 5.701075] hub 3-0:1.0: hub_suspend [ 5.701078] usb usb3: bus auto-suspend [ 5.701081] usb usb3: suspend_rh [ 5.701099] hub 4-0:1.0: hub_suspend [ 5.701102] usb usb4: bus auto-suspend [ 5.701103] usb usb4: suspend_rh [ 5.701120] hub 5-0:1.0: hub_suspend [ 5.701122] usb usb5: bus auto-suspend [ 5.701124] usb usb5: suspend_rh [ 5.701141] hub 6-0:1.0: hub_suspend [ 5.701143] usb usb6: bus auto-suspend [ 5.701145] usb usb6: suspend_rh [ 5.701161] hub 8-0:1.0: hub_suspend [ 5.701164] usb usb8: bus auto-suspend [ 5.701165] usb usb8: suspend_rh [ 5.701182] hub 7-0:1.0: hub_suspend [ 5.701185] usb usb7: bus auto-suspend [ 5.701186] usb usb7: suspend_rh [ 7.006792] udev: starting version 141 [ 7.055529] usb usb3: uevent [ 7.055547] usb 3-0:1.0: uevent [ 7.055638] usb usb4: uevent [ 7.055654] usb 4-0:1.0: uevent [ 7.055739] usb usb5: uevent [ 7.055756] usb 5-0:1.0: uevent [ 7.055841] usb usb1: uevent [ 7.055857] usb 1-0:1.0: uevent [ 7.056387] usb usb6: uevent [ 7.056405] usb 6-0:1.0: uevent [ 7.056493] usb usb7: uevent [ 7.056511] usb 7-0:1.0: uevent [ 7.056596] usb usb8: uevent [ 7.056612] usb 8-0:1.0: uevent [ 7.056695] usb usb2: uevent [ 7.056712] usb 2-0:1.0: uevent [ 7.056745] usb 2-3: uevent [ 7.056763] usb 2-3:1.0: uevent [ 7.056797] usb 2-3:1.1: uevent [ 7.192491] wl: module license 'MIXED/Proprietary' taints kernel. [ 7.194482] wl 0000:04:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 [ 7.194496] wl 0000:04:00.0: setting latency timer to 64 [ 7.210020] eth1 (wl): not using net_device_ops yet [ 7.210822] eth1: Broadcom BCM4315 802.11 Wireless Controller 5.10.91.9 [ 7.614750] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0 [ 7.614767] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 [ 7.614858] HDA Intel 0000:00:1b.0: setting latency timer to 64 [ 7.766982] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/input/input7 [ 7.771103] input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/input/input8 [ 7.775091] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/input/input9 [ 7.873037] rc used greatest stack depth: 5872 bytes left [ 13.260390] cp used greatest stack depth: 5836 bytes left [ 14.315764] usb usb3: uevent [ 14.315822] usb 3-0:1.0: uevent [ 14.316094] usb usb4: uevent [ 14.316150] usb 4-0:1.0: uevent [ 14.316421] usb usb5: uevent [ 14.316478] usb 5-0:1.0: uevent [ 14.316733] usb usb1: uevent [ 14.316789] usb 1-0:1.0: uevent [ 14.318914] usb usb6: uevent [ 14.318972] usb 6-0:1.0: uevent [ 14.319240] usb usb7: uevent [ 14.319299] usb 7-0:1.0: uevent [ 14.319573] usb usb8: uevent [ 14.319628] usb 8-0:1.0: uevent [ 14.319875] usb usb2: uevent [ 14.319931] usb 2-0:1.0: uevent [ 14.320053] usb 2-3: uevent [ 14.320111] usb 2-3:1.0: uevent [ 14.320228] usb 2-3:1.1: uevent [ 15.412760] tg3 0000:07:00.0: PME# disabled [ 15.413005] tg3 0000:07:00.0: irq 31 for MSI/MSI-X [ 15.466497] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 17.098680] tg3: eth0: Link is up at 100 Mbps, full duplex. [ 17.098680] tg3: eth0: Flow control is on for TX and on for RX. [ 17.099173] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 22.811026] dhcpcd-run-hook used greatest stack depth: 5796 bytes left [ 22.979605] Adding 2939480k swap on /dev/sda3. Priority:-1 extents:1 across:2939480k [ 25.542035] eth1: no IPv6 routers present [ 27.759023] eth0: no IPv6 routers present