Dotaz: Technisat Airstar2 neladi+dotaz na spokojene uzivatele

[Radek Hladik]

Dneska jsem se cely vecer trapil s DVB-T kartou technisat airstar2 a nakonec jsem usoudil, ze je problem v karte :)

Kazdopadne jsem z toho jelen, treba mi nekdo poradi:

Kernel 2.6.11 (z FC4, neupdatovany):

1) Ve slotu sdilenem s AGP karta nenajde frontend, v jinem slotu se zda byt v poradku. Nekdy nenajde MAC adresu, jindy je MAC v poradku. Nejspis to asi taky souvisi se slotem, ale moc jsem se tomu nevenoval.

2) Pokud najde frontend, pak nic nenascanuje ani nenaladi (kaffeine, tzap,vlc)

3) Je jedno, zda se pouzije modul skystar2 nebo b2c2_flexcop_pci

Kernel 2.6.15 (nejnovejsi updatovany):

1) Modul b2c2_flexcop_pci najde frontend (ve vsech slotech), ale zase mi na nem nefunguje tzap (pry to neni OFDM aka DVB-T tuner)

2) Pri detekci karty najde frontend Broadcom bcm3510 misto Zarlink MT352, jak je uvedeno v http://www.abclinuxu.cz/hardware/show/64303. (ve vypisu lspci se karta shoduje s onim zapisem vcetne revize)

3)Nevsiml jsem si, ze by karta nasla MAC adresu

4)VLC prohlasi, ze naslo tuner broadcom, ale ze ho nezna, ze je type=3

Windows XP:

1) Kartu najdou, nainstalujou driver (i na sitovku), ale pro zmenu nic nenaladi :(

2) Jednou mi dokonce kartu nasly jako DVB-S, ale Astru jsem na pokojovou antenu nechytil :)

Co se anteny tyce, tak mam takovou tu klasickou pokojovou se zesilovacem, zkousel jsem zesilovac vypnout i zapnout. Antena ma primy vyhled na Zizkov a v set-top boxu funguje naprosto bezproblemove, signal to ukazuje cca 90%.

Navic mi ta karta docela dost hreje, predevsim vsechny kovovy casti. Jeste ke vsemu je na karte nejake nemecke varovani, ze ktereho jsem pochopil, ze karta kvuli napajeni aktivnich anten vyrabi 5V a v pripade pripojeni na OFDM modulator (at uz je to co je to ) se musi vzycky pouzit DC-Block (to asi bude neco, co tech 5V nepusti do toho modulatoru ).

A jako posledni vec: karta ma dva konektory na antenu, s nejvetsi pravedepodobnosti je jeden IN a druhy OUT (podle lakonickeho popisu na vrsku zaslepky jsou oba ANT ). Antenu jsem zapojoval do toho horniho (samice) stejne jako na settop boxu.

Zaverem bych se rad zeptal spokojenych uzivatelu karty:

1) Take vam karta tolik topi?

2) Opravdu se antena zapojuje do toho horniho konektoru? (takove detaily v navodu pro jistotu nejsou)

3) Najde vam karta vzdycky MAC adresu? Ne ze by me to sitovani po te karte nejak zajimalo, ale pripada mi to divne...

4) Pouzivate nekdo kartu ve FC4 a s jakym kernelem a modulem?

Radek

Odpovědi

[Milan Beneš]

1) Tuner má cca 40˚C, ten chip vzadu je ok, mám větrák v bočnici.
2) Anténa se zapojuje do samice... Je nad ní napsáno ANT
3) Tohle jsem nezkoumal. V /proc/net/dev karta není.
4) Mám Gentoo s gentoo-sources-2.6.15-r2, používám Kaffeine 0.7.1 a
   linuxtv-dvb-apps-1.1.0_p20050702.

orthank saruman # lspci
00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different version?) (rev c1)
00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 0 (rev c1)
00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller (rev a4)
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI Bridge (rev a3)
00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
01:07.0 Multimedia audio controller: Creative Labs SB Audigy (rev 04)
01:07.1 Input device controller: Creative Labs SB Audigy MIDI/Game port (rev 04)
01:07.2 FireWire (IEEE 1394): Creative Labs SB Audigy FireWire Port (rev 04)
01:08.0 Network controller: Techsan Electronics Co Ltd B2C2 FlexCopII DVB chip / Technisat SkyStar2 DVB card (rev 02)
02:00.0 VGA compatible controller: nVidia Corporation NV43 [GeForce 6600/GeForce 6600 GT] (rev a2)

orthank saruman # dmesg
>PCI: nForce2 C1 Halt Disconnect fixup
Boot video device is 0000:02:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK2] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK3] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK4] (IRQs 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [LNK5] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LUBA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUBB] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LMAC] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LAPU] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LACI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LMCI] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LSMB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LUB2] (IRQs 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LFIR] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [L3CM] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LIDE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [APC1] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APC2] (IRQs *17), disabled.
ACPI: PCI Interrupt Link [APC3] (IRQs *18), disabled.
ACPI: PCI Interrupt Link [APC4] (IRQs *19), disabled.
ACPI: PCI Interrupt Link [APC5] (IRQs *16), disabled.
ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCI] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCS] (IRQs *23), disabled.
ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [AP3C] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22) *0, disabled.
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Bridge: 0000:00:08.0
  IO window: d000-dfff
  MEM window: e3000000-e3ffffff
  PREFETCH window: disabled.
PCI: Bridge: 0000:00:1e.0
  IO window: disabled.
  MEM window: e0000000-e2ffffff
  PREFETCH window: d0000000-dfffffff
PCI: Setting latency timer of device 0000:00:08.0 to 64
Machine check exception polling timer started.
highmem bounce pool size: 64 pages
NTFS driver 2.1.25 [Flags: R/O].
fuse init (API version 7.3)
io scheduler noop registered
io scheduler cfq registered
vesafb: NVIDIA Corporation, nv43 Board - 21812011, Chip Rev    (OEM: NVIDIA)
vesafb: VBE version: 3.0
vesafb: VBIOS/hardware doesn't support DDC transfers
vesafb: no monitor limits have been set
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 160x64
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 10240k, total 131072k
fb0: VESA VGA frame buffer device
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
Real Time Clock Driver v1.12
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected NVIDIA nForce2 chipset
agpgart: AGP aperture is 256M @ 0xc0000000
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.48.
ACPI: PCI Interrupt Link [APCH] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 22 (level, high) -> IRQ 16
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
flexcop-pci: will use the HW PID filter.
flexcop-pci: card revision 2
ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18
ACPI: PCI Interrupt 0000:01:08.0[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 17
DVB: registering new adapter (FlexCop Digital TV device).
b2c2-flexcop: MAC address = 00:d0:d7:01:c5:a1
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: i2c master_xfer failed
b2c2-flexcop: found the mt352 at i2c address: 0x0f
DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb' complete
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: Maxtor 6Y160P0, ATA DISK drive
hdb: ST310211A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ASUS DVD-ROM DVD-E616P 0104, ATAPI CD/DVD-ROM drive
hdd: _NEC DVD_RW ND-3520A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 320173056 sectors (163928 MB) w/7936KiB Cache, CHS=19929/255/63, UDMA(133)
hda: cache flushes supported
 hda: hda1 hda2
hdb: max request size: 128KiB
hdb: 19541088 sectors (10005 MB) w/1024KiB Cache, CHS=19386/16/63, UDMA(100)
hdb: cache flushes not supported
 hdb: hdb1
hdc: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
ohci1394: $Rev: 1313 $ Ben Collins (bcollins@debian.org)
ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16
ACPI: PCI Interrupt 0000:01:07.2[B] -> Link [APC1] -> GSI 16 (level, high) -> IRQ 18
ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[18]  MMIO=[e3014000-e30147ff]  Max Packet=[2048]
ieee1394: raw1394: /dev/raw1394 device initialized
sbp2: $Rev: 1306 $ Ben Collins (bcollins@debian.org)
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
usbmon: debugfs is not available
ACPI: PCI Interrupt Link [APCL] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [APCL] -> GSI 21 (level, high) -> IRQ 19
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: irq 19, io mem 0xe4003000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [APCF] -> GSI 20 (level, high) -> IRQ 20
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 20, io mem 0xe4001000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [APCG] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [APCG] -> GSI 22 (level, high) -> IRQ 16
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 16, io mem 0xe4002000
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
Initializing USB Mass Storage driver...
usb 2-2: new full speed USB device using ohci_hcd and address 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb 3-1: new low speed USB device using ohci_hcd and address 2
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00023c01510e4cb5]
input: Microsoft Microsoft Wireless Optical DesktopŽ 1.00 as /class/input/input1
input: USB HID v1.11 Keyboard [Microsoft Microsoft Wireless Optical DesktopŽ 1.00] on usb-0000:00:02.1-1
input: Microsoft Microsoft Wireless Optical DesktopŽ 1.00 as /class/input/input2
input: USB HID v1.11 Mouse [Microsoft Microsoft Wireless Optical DesktopŽ 1.00] on usb-0000:00:02.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core
drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303
pl2303 2-2:1.0: pl2303 converter detected
usb 2-2: pl2303 converter now attached to ttyUSB0
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver
i2c /dev entries driver
i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5000
i2c_adapter i2c-2: nForce2 SMBus adapter at 0x5500
i2c_adapter i2c-0: SMBus Quick command not supported, can't probe for chips
Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC).
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI Interrupt 0000:01:07.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 21
Installing spdif_bug patch: Audigy 2 ZS [SB0350]
ALSA device list:
  #0: Audigy 2 ZS [SB0350] (rev.4, serial:0x20021102) at 0xd000, irq 21
NET: Registered protocol family 2
IP route cache hash table entries: 65536 (order: 6, 262144 bytes)
TCP established hash table entries: 262144 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Using IPI Shortcut mode
ACPI wakeup devices:
HUB0 HUB1 USB0 USB1 USB2 F139 MMAC MMCI UAR1
ACPI: (supports S0 S1 S4 S5)
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 188k freed
Adding 1502068k swap on /dev/hda2.  Priority:-1 extents:1 across:1502068k
nvidia: module license 'NVIDIA' taints kernel.
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 21
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module  1.0-8178  Wed Dec 14 16:22:51 PST 2005
lirc_dev: IR Remote Control driver registered, at major 61
lirc_serial: auto-detected active low receiver
lirc_dev: lirc_register_plugin: sample_rate: 0

LOL, našel jsem MAC adresu

no, nejspíš bude chyba v kartě

[watslaw]

Já mám podobný problém, ale poprvé to dopadlo dobře:

...
Feb 22 20:50:05 delfin kernel: b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
Feb 22 20:50:05 delfin kernel: flexcop-pci: will use the HW PID filter.
Feb 22 20:50:05 delfin kernel: flexcop-pci: card revision 2
Feb 22 20:50:05 delfin kernel: ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 193
Feb 22 20:50:05 delfin kernel: DVB: registering new adapter (FlexCop Digital TV device).
Feb 22 20:50:05 delfin kernel: b2c2-flexcop: MAC address = 00:d0:d7:0d:d3:b7
Feb 22 20:50:05 delfin kernel: b2c2-flexcop: found the mt352 at i2c address: 0x0f
Feb 22 20:50:05 delfin kernel: DVB: registering frontend 0 (Zarlink MT352 DVB-T)...
Feb 22 20:50:05 delfin kernel: b2c2-flexcop: initialization of 'Air2PC/AirStar 2 DVB-T' at the 'PCI' bus controlled by a 'FlexCopIIb'
 complete
Feb 22 20:50:05 delfin kernel: ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 201
Feb 22 20:50:05 delfin kernel: NET: Registered protocol family 10
...

ale stanice to nenaladilo. Při dalších bootech to dopadlo takto:

Feb 23 13:18:42 delfin kernel: b2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully
Feb 23 13:18:42 delfin kernel: flexcop-pci: will use the HW PID filter.
Feb 23 13:18:42 delfin kernel: flexcop-pci: card revision 2
Feb 23 13:18:42 delfin kernel: ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 18 (level, low) -> IRQ 193
Feb 23 13:18:42 delfin kernel: DVB: registering new adapter (FlexCop Digital TV device).
Feb 23 13:18:42 delfin kernel: b2c2-flexcop: reading of MAC address failed.
Feb 23 13:18:42 delfin kernel:
Feb 23 13:18:42 delfin kernel: ACPI: PCI Interrupt 0000:00:05.0[A] -> GSI 16 (level, low) -> IRQ 201
Feb 23 13:18:42 delfin kernel: mt352_read_register: readreg error (reg=127, ret==-121)
Feb 23 13:18:42 delfin kernel: i2c_readbytes: i2c read error (addr 0a, err == -121)
Feb 23 13:18:42 delfin kernel: lgdt330x: i2c_read_demod_bytes: addr 0x59 select 0x02 error (ret == -121)
Feb 23 13:18:42 delfin kernel: stv0297_readreg: readreg error (reg == 0x80, ret == -22)
Feb 23 13:18:42 delfin kernel: ACPI: PCI interrupt for device 0000:00:07.0 disabled
Feb 23 13:18:42 delfin kernel: NET: Registered protocol family 10
...

Jádro 2.6.15

Čím by to mohlo být? Kdyby to nefungovalo od počátku, tak bych to chápal.

[watslaw]

Takže jsem se inspiroval zde: http://pvrguide.no-ip.com/bbs-old/viewtopic.php?t=35281

pomohlo přendat do jiného PCI slotu, a MAC už přečíst jde.

[Radek Hladik]

S normalni antenou (klasicka jagina bez predzesilovace) vsechno funguje. Antena s predzesilovacem se musela zapojit do druheho (vystupniho) konektoru (naprosto netusim proc )

Radek

[Pavel Jenicek]

Take jsem mel problemy s ladenim, na stejne zasuvce stolni prijimac super, airstar2 nic.

Reseni:

1. Pozor na zlutou nalepku, ktera (ac nemecky) rika, ze karta poskytuje napajeni 5V pro aktivni antenu. Pokud tam chcete pripojit pasiv, tak pres oddelovac DC slozky, pokud pouzivate (jako ja) aktivni zesilovac napajeny z koaxialniho kabelu, pak je jiz DC oddelovac instalovan.

2. Velky problem (mimo jine take casto diskutovany) se zemnim potencialem anteny a kolikem zasuvky (s niz je pojena kostra PC a tedy i zeme antenniho vstupu do karty). Ja tam nameril neuveritelnych 92V!!

Reseni: v obchodech se satelitni technikou jsem koupil (220,-Kc) "GROUND BREAKER" tedy oddelovac zeme. Po zapojeni mezi privod a kartu je prijem vyborny.

Poznamka pro Ostravske: DVB vysila z Hladnova na 39 kanale, tedy 618 Mhz, jinde to nenaladite :)

[Hola]

Tak se zkus podivat sem... taky zkoumam co koupit... a tak brousim kde se da. Tady je jakoze vysvetleni... co kde jak.. neni to sice pro linux ale to k vysvetleni proc to neladi nevadi ;o) ladi neladi. http://www.czechcomputer.cz/disc_doc-P99048BE5398CC817C12570BD0046CD6A.html?&all=1