Portál AbcLinuxu, 20. dubna 2024 05:06
# dmesg
Linux version 2.6.17-gentoo-r4 (root@Server) (gcc version 3.4.4 (Gentoo 3.4.4-r1, ssp-3.4.4-1.0, pie-8.7.8)) #1 SMP Mon Jul 31 10:39:53 Local time zone must be set--see zic
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000fcf0000 (usable)
BIOS-e820: 000000000fcf0000 - 000000000fcfb000 (ACPI data)
BIOS-e820: 000000000fcfb000 - 000000000fd00000 (ACPI NVS)
BIOS-e820: 000000000fd00000 - 000000000fe80000 (usable)
BIOS-e820: 000000000fe80000 - 0000000010000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
0MB HIGHMEM available.
254MB LOWMEM available.
found SMP MP-table at 000f62f0
On node 0 totalpages: 65152
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 61056 pages, LIFO batch:15
DMI present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f62c0
ACPI: RSDT (v001 PTLTD RSDT 0x060400d0 LTP 0x00000000) @ 0x0fcf7641
ACPI: FADT (v001 IBM NETVISTA 0x060400d0 PTL 0x00000001) @ 0x0fcfaee2
ACPI: TCPA (v001 IBM NETVISTA 0x060400d0 PTL 0x00000001) @ 0x0fcfaf56
ACPI: MADT (v001 PTLTD APIC 0x060400d0 LTP 0x00000000) @ 0x0fcfaf88
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x060400d0 LTP 0x00000001) @ 0x0fcfafd8
ACPI: DSDT (v001 IBM Yelotail 0x060400d0 MSFT 0x0100000d) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:1 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 20000000 (gap: 10000000:eec00000)
Built 1 zonelists
Kernel command line: root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3 udev
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c048e000 soft=c0486000
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 1694.845 MHz processor.
Using pmtmr for high-res timesource
Speakup v-2.00 CVS: Mon May 1 09:46:33 EDT 2006 : initialized
Console: colour VGA+ 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 251800k/260608k available (2506k kernel code, 8208k reserved, 846k data, 212k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3393.80 BogoMIPS (lpj=6787600)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 3febfbff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 128K
CPU: Hyper-Threading is disabled
CPU: After all inits, caps: 3febfbff 00000000 00000000 00000080 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
CPU0: Intel(R) Celeron(R) CPU 1.70GHz stepping 03
Total of 1 processors activated (3393.80 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=0 apic2=-1 pin2=-1
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 1971k freed
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd98d, last bus=2
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 1180-11bf claimed by ICH4 GPIO
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.SLOT._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1e.0
IO window: 2000-2fff
MEM window: c0100000-c01fffff
PREFETCH window: 20000000-200fffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 4096)
TCP reno registered
Simple Boot Flag at 0x6c set to 0x1
* This chipset may have PM-Timer Bug. Due to workarounds for a bug,
* this time source is slow. If you are sure your timer does not have
* this bug, please use "pmtmr_good" to disable the workaround
audit: initializing netlink socket (disabled)
audit(1158601262.148:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.0 (2006/03/15) Phillip Lougher
SGI XFS with ACLs, security attributes, realtime, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
Initializing Cryptographic API
io scheduler noop registered
io scheduler deadline registered (default)
initialized device: /dev/synth, node ( MAJOR 10, MINOR 25 )
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 845G Chipset.
agpgart: Detected 892K stolen memory.
agpgart: AGP aperture is 128M @ 0x88000000
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0c: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PSM] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
loop: loaded (max 8 devices)
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller at PCI slot 0000:00:1f.1
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 177
ICH4: chipset revision 1
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1860-0x1867, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1868-0x186f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
input: AT Translated Set 2 keyboard as /class/input/input0
hda: WDC WD153AA, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SAMSUNG CD-ROM SC-148C, ATAPI CD/DVD-ROM drive
hdc: Disabling (U)DMA for SAMSUNG CD-ROM SC-148C (blacklisted)
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 30064608 sectors (15393 MB) w/2048KiB Cache, CHS=29826/16/63, UDMA(66)
hda: cache flushes not supported
hda: hda1 hda2 hda3
hdc: ATAPI 48X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.20
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 1
Cannot allocate resource for EISA slot 2
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 212k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 185, io mem 0xc0080000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 193
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 193, io base 0x00001800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 201
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 201, io base 0x00001820
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 177, io base 0x00001840
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
sl811: driver sl811-hcd, 19 May 2005
ieee1394: Initialized config rom entry `ip1394'
ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
ieee1394: sbp2: Try serialize_io=0 for better performance
libata version 1.20 loaded.
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
ReiserFS: hda3: warning: sh-2021: reiserfs_fill_super: can not find reiserfs on hda3
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Adding 506036k swap on /dev/hda2. Priority:-1 extents:1 across:506036k
EXT3 FS on hda3, internal journal
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:02:0c.0: 3Com PCI 3c905B Cyclone 100baseTx at d0998000.
Real Time Clock Driver v1.12ac
ACPI: PCI Interrupt 0000:02:0c.0[A] -> GSI 20 (level, low) -> IRQ 209
eth0: setting half-duplex.
eth0: setting full-duplex.
APIC error on CPU0: 00(60)
APIC error on CPU0: 60(60)
APIC error on CPU0: 60(60)
19.9.2006 23:10
noapic
# cat /boot/grub/grub.conf
default 0
timeout 10
title=Gentoo Linux
root (hd0,0)
kernel /boot/kernel-genkernel-x86-2.6.17-gentoo-r4 root=/dev/ram0 init=/linuxrc ramdisk=8192 real_root=/dev/hda3 udev apic=off
initrd /boot/initramfs-genkernel-x86-2.6.17-gentoo-r4
Simple Boot Flag at 0x6c set to 0x1 * This chipset may have PM-Timer Bug. Due to workarounds for a bug, * this time source is slow. If you are sure your timer does not have * this bug, please use "pmtmr_good" to disable the workaroundtakze si pohladaj nieco o tom na google. Alebo poexperimentuj, ci je to cele ovplyvnene zapnutim/vypnutim APIC/ACPI. A posledna vec "tiche" nemusi znamenat "dobre chladene". Obzvlast pri takom to evidentne "prehriavajucom sa" chovani, by som to odskusal s nejakym vetrakom bez regulacie, ale zato poriadne beziacom.
Zatim díky za Vaše reakce
cat /dev/urandom >/dev/nulla v druhom
for i in {1..1000}; do echo -n "$i "; cat /proc/acpi/thermal_zone/THRM/temperature; sleep 1; done
pripadne cez lm_sensors si periodicky pozerat teplotu.
Ak ti teplota nefunguje, tak aspion bedes sledovat, ci vypisuje cisla po sekunde.
Děkuji Vám mnohokrát (parametr noapic pomohl)
Tiskni
Sdílej:
ISSN 1214-1267, (c) 1999-2007 Stickfish s.r.o.