Dotaz: FujitsuSiemens Amilo Pro V3205 a ipw3945

[Aetos]

Zdravím, pokouším se zprovoznit už delší dobu wifi na Debianu ( Intel PRO/Wireless 3945ABG Network Connection ) ale nějak se mi nedaří. Modul ipw3945 mám zavedený daemon ipw3945d taky běží, ale při příkazu (viz. dále) mi to vypiše toto:

debian-lukas:/home/lukas# ipw3945d --pid-file=/var/run/ipw3945.pid
ipw3945d - regulatory daemon
Copyright (C) 2005-2006 Intel Corporation. All rights reserved.
version: 1.7.22
2008-11-03 23:44:31: ERROR: Could not find Intel PRO/Wireless 3945ABG Network Connection

Jako by to nevidělo mojí kartu Neporadil by mi někdo kde dělám chybu?

Odpovědi

[Jiří P.]

verze jádra? Chyba se projevila po upgradu? dmesg výstup?

[Aetos]

děkuji za rady

chyba se neprojevila po upgradu jádra, nikdy totiž mi na tomto notebooku wifi neběhala

dmesg

debian-lukas:/home/lukas# dmesg
Linux version 2.6.18-6-686-bigmem (Debian 2.6.18.dfsg.1-23) (dannf@debian.org) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 SMP Mon Oct 13 17:32:29 UTC 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001f690000 (usable)
 BIOS-e820: 000000001f690000 - 000000001f698000 (ACPI data)
 BIOS-e820: 000000001f698000 - 000000001f700000 (ACPI NVS)
 BIOS-e820: 000000001f700000 - 0000000020000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff000000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
502MB LOWMEM available.
found SMP MP-table at 000f76d0
NX (Execute Disable) protection: active
On node 0 totalpages: 128656
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 124560 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v000 PTLTD                                 ) @ 0x000f7590
ACPI: RSDT (v001 FUJ___ DW1_____ 0x20060721  LTP 0x00000000) @ 0x1f691e9c
ACPI: FADT (v001 FUJ___ DW1_____ 0x20060721 LOHR 0x0000005a) @ 0x1f697e20
ACPI: MADT (v001 FUJ___ DW1_____ 0x20060721 LOHR 0x0000005a) @ 0x1f697e94
ACPI: BOOT (v001 FUJ___ DW1_____ 0x20060721  LTP 0x00000001) @ 0x1f697fd8
ACPI: MCFG (v001 FUJ___ DW1_____ 0x20060721 LOHR 0x0000005a) @ 0x1f697f34
ACPI: MADT (v001 FUJ___ DW1_____ 0x20060721  LTP 0x00000000) @ 0x1f697f70
ACPI: SSDT (v001  PmRef    CpuPm 0x00003000 INTL 0x20050228) @ 0x1f691ed8
ACPI: DSDT (v001 FUJ___ DW1_____ 0x20060721 MSFT 0x0100000e) @ 0x00000000
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: 2 duplicate APIC table ignored.
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:14 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:14 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:c0000000)
Detected 1729.647 MHz processor.
Built 1 zonelists.  Total pages: 128656
Kernel command line: root=/dev/sda6 ro
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 502080k/514624k available (1542k kernel code, 11936k reserved, 587k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3463.12 BogoMIPS (lpj=6926240)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel Genuine Intel(R) CPU           T2250  @ 1.73GHz stepping 08
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3459.32 BogoMIPS (lpj=6918655)
CPU: After generic identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
CPU: After vendor identify, caps: bfe9fbff 00100000 00000000 00000000 0000c189 00000000 00000000
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfe9fbff 00100000 00000000 00000940 0000c189 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel Genuine Intel(R) CPU           T2250  @ 1.73GHz stepping 08
Total of 2 processors activated (6922.44 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=51
checking if image is initramfs... it is
Freeing initrd memory: 4804k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:00:02.0
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Firmware left 0000:07:08.0 e100 interrupts enabled, disabling
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15)
ACPI: Embedded Controller [EC0] (gpe 23) interrupt mode.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 8 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
PCI: Ignore bogus resource 6 [0:0] of 0000:00:02.0
PCI: Bridge: 0000:00:1c.0
  IO window: 2000-2fff
  MEM window: da000000-dbffffff
  PREFETCH window: d4000000-d5ffffff
PCI: Bridge: 0000:00:1c.1
  IO window: 3000-3fff
  MEM window: d6000000-d7ffffff
  PREFETCH window: d0000000-d1ffffff
PCI: Bridge: 0000:00:1c.2
  IO window: 4000-4fff
  MEM window: d8000000-d9ffffff
  PREFETCH window: d2000000-d3ffffff
PCI: Bridge: 0000:00:1e.0
  IO window: 5000-5fff
  MEM window: dc000000-dc0fffff
  PREFETCH window: disabled.
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:00:1c.0 to 64
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1c.1 to 64
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1c.2 to 64
PCI: Enabling device 0000:00:1e.0 (0004 -> 0007)
PCI: Setting latency timer of device 0000:00:1e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
Simple Boot Flag value 0x82 read from CMOS RAM was invalid
Simple Boot Flag at 0x36 set to 0x1
audit: initializing netlink socket (disabled)
audit(1225798065.992:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.0:pcie00]
Allocate Port Service[0000:00:1c.0:pcie02]
Allocate Port Service[0000:00:1c.0:pcie03]
PCI: Setting latency timer of device 0000:00:1c.1 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.1:pcie00]
Allocate Port Service[0000:00:1c.1:pcie02]
Allocate Port Service[0000:00:1c.1:pcie03]
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[0000:00:1c.2:pcie00]
Allocate Port Service[0000:00:1c.2:pcie02]
Allocate Port Service[0000:00:1c.2:pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2F] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S3 S4 S5)
Time: tsc clocksource has been installed.
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu0Cst] [20060707]
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Ist] [20060707]
ACPI (exconfig-0455): Dynamic SSDT Load - OemId [ PmRef] OemTableId [ Cpu1Cst] [20060707]
ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
ACPI: Processor [CPU1] (supports 8 throttling states)
ACPI: Thermal Zone [TZ00] (53 C)
Time: acpi_pm clocksource has been installed.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 185
ICH7: chipset revision 2
ICH7: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0x1810-0x1817, BIOS settings: hda:DMA, hdb:pio
Probing IDE interface ide0...
USB Universal Host Controller Interface driver v3.0
SCSI subsystem initialized
libata version 2.00 loaded.
ieee1394: Initialized config rom entry `ip1394'
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
hda: HL-DT-ST DVDRAM GSA-T10N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 225, io mem 0xdc444000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hda: ATAPI 24X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
PCI: Enabling device 0000:07:09.0 (0000 -> 0002)
ACPI: PCI Interrupt 0000:07:09.0[A] -> GSI 20 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:07:09.0 to 64
ohci1394: fw-host0: OHCI-1394 1.0 (PCI): IRQ=[233]  MMIO=[dc001000-dc0017ff]  Max Packet=[2048]  IR/IT contexts=[4/4]
ahci 0000:00:1f.2: version 2.0
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 50
usb 1-2: new high speed USB device using ehci_hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: waiting for device to settle before scanning
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 1.5 Gbps 0x5 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq pm led clo pio slum part
ata1: SATA max UDMA/133 cmd 0xE001E500 ctl 0x0 bmdma 0x0 irq 58
ata2: SATA max UDMA/133 cmd 0xE001E580 ctl 0x0 bmdma 0x0 irq 58
ata3: SATA max UDMA/133 cmd 0xE001E600 ctl 0x0 bmdma 0x0 irq 58
ata4: SATA max UDMA/133 cmd 0xE001E680 ctl 0x0 bmdma 0x0 irq 58
scsi1 : ahci
ieee1394: Host added: ID:BUS[0-00:1023]  GUID[00c09f0000b2ffc2]
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata1.00: ATA-8, max UDMA/100, 234441648 sectors: LBA48 NCQ (depth 31/32)
ata1.00: ata1: dev 0 multi count 16
ata1.00: configured for UDMA/100
scsi2 : ahci
ata2: SATA link down (SStatus 0 SControl 0)
scsi3 : ahci
ata3: SATA link down (SStatus 0 SControl 300)
scsi4 : ahci
ata4: SATA link down (SStatus 0 SControl 0)
  Vendor: ATA       Model: FUJITSU MHW2120B  Rev: 0000
  Type:   Direct-Access                      ANSI SCSI revision: 05
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 225
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 225, io base 0x00001820
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
 sda: sda1 sda2 < sda5 sda6 sda7<6>ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 50
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 50, io base 0x00001840
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
 sda8 sda9 >
sd 1:0:0:0: Attached scsi disk sda
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 185
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 185, io base 0x00001860
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 177, io base 0x00001880
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:07:08.0[A] -> GSI 20 (level, low) -> IRQ 233
PCI: Setting latency timer of device 0000:07:08.0 to 64
e100: eth0: e100_probe: addr 0xdc000000, irq 233, MAC addr 00:16:36:83:60:1F
usb 3-1: new low speed USB device using uhci_hcd and address 2
usb 3-1: configuration #1 chosen from 1 choice
usbcore: registered new driver hiddev
input: Genius Optical Mouse as /class/input/input1
input: USB HID v1.10 Mouse [Genius Optical Mouse] on usb-0000:00:1d.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
  Vendor: Verbatim  Model: Store 'n' Go      Rev: 1.30
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sdb: 2015231 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 2015231 512-byte hdwr sectors (1032 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 00 00 00
sdb: assuming drive cache: write through
 sdb:<6>Linux agpgart interface v0.101 (c) Dave Jones
 sdb1
sd 0:0:0:0: Attached scsi removable disk sdb
usb-storage: device scan complete
ts: Compaq touchscreen protocol output
agpgart: Detected an Intel 945GM Chipset.
agpgart: Detected 7932K stolen memory.
agpgart: AGP aperture is 256M @ 0xc0000000
intel_rng: FWH not detected
sdhci: Secure Digital Host Controller Interface driver, 0.12
sdhci: Copyright(c) Pierre Ossman
sdhci: SDHCI controller found at 0000:07:09.1 [1180:0822] (rev 19)
PCI: Enabling device 0000:07:09.1 (0000 -> 0002)
ACPI: PCI Interrupt 0000:07:09.1[B] -> GSI 21 (level, low) -> IRQ 66
PCI: Setting latency timer of device 0000:07:09.1 to 64
mmc0: SDHCI at 0xdc001800 irq 66 DMA
Real Time Clock Driver v1.12ac
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation 
ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 50
input: PC Speaker as /class/input/input2
ipw3945: Intel(R) PRO/Wireless 3945 Network Connection driver for Linux, 1.1.2dmpr
ipw3945: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 177
PCI: Setting latency timer of device 0000:01:00.0 to 64
ipw3945: Detected Intel PRO/Wireless 3945ABG Network Connection
ipw3945: ipw3945.ucode load failed: Reason -2
ipw3945: Could not read microcode: -2
ACPI: PCI interrupt for device 0000:01:00.0 disabled
ipw3945: probe of 0000:01:00.0 failed with error -2
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 74
PCI: Setting latency timer of device 0000:00:1b.0 to 64
Synaptics Touchpad, model: 1, fw: 5.10, id: 0x258eb1, caps: 0xa04713/0x0
input: SynPS/2 Synaptics TouchPad as /class/input/input3
Adding 923696k swap on /dev/sda7.  Priority:-1 extents:1 across:923696k
EXT3 FS on sda6, internal journal
device-mapper: ioctl: 4.7.0-ioctl (2006-06-24) initialised: dm-devel@redhat.com
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
e100: eth1: e100_watchdog: link up, 100Mbps, half-duplex
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
vboxadd: VirtualBox PCI device not found.
vboxadd: VirtualBox PCI device not found.
vboxvfs: Unknown symbol vboxadd_cmc_open
vboxvfs: Unknown symbol RTLogBackdoorPrintf
vboxvfs: Unknown symbol vboxadd_cmc_ctl_guest_filter_mask
vboxvfs: Unknown symbol RTErrConvertToErrno
vboxvfs: Unknown symbol vboxadd_cmc_call
vboxvfs: Unknown symbol RTAssertDoBreakpoint
vboxvfs: Unknown symbol vboxadd_cmc_close
vboxvfs: Unknown symbol AssertMsg2
vboxvfs: Unknown symbol AssertMsg1
ACPI: Battery Slot [BAT1] (battery present)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ACPI: Sleep Button (CM) [SLPB]
ACPI: Lid Switch [LID]
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
eth1: no IPv6 routers present
Loading iSCSI transport class v1.1-646.<5>iscsi: registered transport (tcp)
iscsi: registered transport (iser)
vboxdrv: Found 2 processor cores.
vboxdrv: fAsync=0 offMin=0x3b5 offMax=0x5d7
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 2.0.4 (interface 0x00090000).
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177
[drm] Initialized i915 1.5.0 20060119 on minor 0
Bluetooth: Core ver 2.10
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!

[Aetos]

debian-lukas:/home/lukas# uname -a
Linux debian-lukas 2.6.18-6-686-bigmem #1 SMP Mon Oct 13 17:32:29 UTC 2008 i686 GNU/Linux

[lukash]

Ahoj,

1) dopln dalsie info (vystup lspci, mas tam naozaj taku kartu?), dmesg a pod.

2) intel ma daleko novsie drivere na tuto kartu, google for iwl3945

L.

[Aetos]

01:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG Network Connection (rev 02)

vypadá to že mám

po tom modulu se podívám, ale na googlu jsem našel návody pro tento notebook a postupoval přesně podle nich a byl to ipw3945.

na druhou stranu jsem našel že by mi to mohlo běhat i s modulem iwlwifi, ale tento modul nemůžu sehnat

[Aetos]

našel jsem na internetu tenhle firware "firmware-iwlwifi_0.13_all" a stáhnul si ho a nainstaloval, ale jaksi lamovsky nevím ja postupovat?

[xavier]

Firmware iwlwifi je pro ovladač iwl3945. Pokud používáš debian stable k skus zadat jako root

apt-get install firmware-ipw3945

Nebo ten balík můžeš nainstalovat pomocí synapticu. Pro použití iwl3945 by musel stáhnout jádro z debian testing. Jinak tahle karta mi fungovala s oběma ovladači. Podrobnější návod pro ipw3945

[alium]

co takhle upgradovat jádro a vyzkoušet funkční driver iwl3945 ??

ipw3945 se přece jen už nevyvíjí...

[Aetos]

Děkuji Vám za radu, ale jelikož linux používám jen 4 měsíce mohl by jste mi naznačit postup jak pokračovat? Byl bych Vám moc vděčen

[Martin Beránek]

driver pro tuto wifi je primo v jadre (od verze 2.6.24) - je doporuceno pouzit ten. Jake mate jadro, zjistite prikazem uname -a. Jakou mate distribuci - vetsina modernich distribuci nema s timto ovladacem problem.

[Aetos]

příkaz uname -a znám ale jádro mám 2.6.18 tak já si pokusím nainstalovat/zkompilovat nové

[Aetos]

Tak, sestavit jádro se mi nepovedlo ( zkoušel jsem 2.6.26.6 ) a po spuštění skončí na hlášce: "Begin: waiting for root file system". Hledal jsem na diskuzních fórech i na abclinuxu a zkoušel postupy co tam doporučovali, ale nic z toho nepomohlo. Ale k věci. Mám teď nainstalováno jádro:

debian-lukas:/home/lukas# uname -a
Linux debian-lukas 2.6.24-etchnhalf.1-686 #1 SMP Mon Oct 13 07:27:05 UTC 2008 i686 GNU/Linux

kartu to sice ihned objevilo, ale jaksi se nemohu nikam připojit a ani žádné sítě nevidím.? Jako by ten ovladač iwl3945 nepracoval s kartou správně. Nechápu, měl bych k tomu nainstalovat ještě nějakého daemona? A nebo jak a co dál....?

[elenril]

Co myslíš tím, že se nemůžeš připojit? Jak ses o to pokoušel?

Jinak tuhle kartu mám a na Debianu mi se všemi jádry od 2.6.24 funguje bez problémů. Stačí firmware a modul, žádní démoni už nejsou potřeba.

[Aetos]

Omlouvám se za nedostatek informací. Takže vypadá to následovně. Start Linuxux lsmod - modul iwl tam je a je tam firmware_class 9472 1 iwl3945. Pak jdu do nastavení sítí deaktivuji eth1, pak aktivuji wlan0 ( aktivac trvá neúměrně dlouho, cca 2 min ). Po tom co naskočí že je wlan0 aktivní, jdu do rozhraní wlan0 - Správce wifi a tam vidím, mimo rozsah, síla signálu 0, Hledám síť dvojtečka a nic atd. Ještě informace; veškerá činost v linuxu je zpomalená, př. na otevření okna terminálu normálně čekám 1 sekundu, ale když mám puštěnou wifi tak to trvá 45 sekund. Myslím že tady asi nebude vše ok. Když kliknu na v\hledat sí%tě, je to se mnou rychle hotovo, ihned naskočí: "vyhledávání bylo dokončeno, ale žádné sítě nenalezeny.

ifconfig

wlan0     Zapouzdření:Ethernet  HWadr (mac adresa)
          VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

wmaster0  Zapouzdření:NEZNÁM  HWadr (mac adresa )
          VŠESMĚROVÉ_VYSÍLÁNÍ MULTICAST  MTU:1500  Metrika:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          kolizí:0 délka odchozí fronty:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

nevím co je to to wmaster. a ještě jedna věc která mi vrtá hlavou: někdy se mi v nastavení sítě objeví možnost vybrat kartu wlan0:avahi . Ale samozřejmě to taky nefunguje.

[elenril]

Zkus tuhle posloupnost příkazů pod rootem:

ip l set wlan0 down
modprobe -vr iwl3945
modprobe -v iwl3945
ip l set wlan0 up
iwlist wlan0 scan

A podívej se na výstup scanovaní a co nového se mezitím objeví v dmesg. Jinak wmaster0 si nevšímej, ten je pro vnitřní použití mac80211 stacku.

[Aetos]

debian-lukas:/home/lukas# iwlist wlan0 scan
wlan0     Scan completed :
          Cell 01 - Address: 00:1B:FC:60:EE:D2
                    ESSID:"pako4"
                    Mode:Master
                    Channel:1
                    Frequency:2.412 GHz (Channel 1)
                    Quality=54/100  Signal level=-76 dBm  Noise level=-127 dBm
                    Encryption key:on
                    IE: WPA Version 1
                        Group Cipher : TKIP
                        Pairwise Ciphers (1) : TKIP
                        Authentication Suites (1) : PSK
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
                              24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s
                              12 Mb/s; 48 Mb/s
                    Extra:tsf=000000bf068d46ae
          Cell 02 - Address: 00:14:BF:B2:42:6C
                    ESSID:"xradaj"
                    Mode:Master
                    Channel:11
                    Frequency:2.462 GHz (Channel 11)
                    Quality=35/100  Signal level=-88 dBm  Noise level=-127 dBm
                    Encryption key:on
                    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
                              24 Mb/s; 36 Mb/s; 54 Mb/s; 6 Mb/s; 9 Mb/s
                              12 Mb/s; 48 Mb/s
                    Extra:tsf=0000009b37e9c18a

tohle vypadá asi vpořádku ale jinak pořád to samé....??

[Aetos]

teď jsem si uvědomil že se mi podailo nějaké síTě vyhledat, ale je jich moc málo a pokaždé musím zadat v terminálu iwlist wlan0 scan. abych se přiznal, nikdy jsem pod debianem wifi nepřipojoval, takže opravdu nevím kdybych se chtěl připojit jak na to? Ale kfyř to srovnám s tím co chytí karta přes windows a tady tak se mi ten signál zdá nějaký špatný..

[elenril]

Na nastavování sítě žádná klikátka nepoužívám, tak s nimi ti moc neporadím. Ale z konzole to vypadá asi tak, že ip l set wlan0 up nahodí síťovku, přes wpa_supplicant se autentizuješ a pak pustíš dhclient. Kdybys to chtěl automatizovat, tak k tomu slouží /etc/network/interfaces, např. takhle mám wifi nakonfigurovanou pro domácí síť

iface wlan0 inet dhcp
    wpa-ssid wiskas                    #SSID sítě
    wpa-bssid xx:xx:xx:xx:xx:xx        #nepovinné - MAC adresa AP
    wpa-psk hodne_dlouhe_cislo         #pokud síť používá WPA2 s preshared key, tak sem přijde výstup wpa_passphrase
    pre-up  modprobe -v iwl3945 && sleep 1 #zavadeni modulu zpomaluje start, tak ho natahuju az je potreba