Initializing cgroup subsys cpuset Linux version 2.6.26.8-57.fc8 (mockbuild@x86-3.fedora.phx.redhat.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 SMP Thu Dec 18 19:19:45 EST 2008 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000002bff0000 (usable) BIOS-e820: 000000002bff0000 - 000000002bffffc0 (ACPI data) BIOS-e820: 000000002bffffc0 - 000000002c000000 (ACPI NVS) BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved) x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 0MB HIGHMEM available. 703MB LOWMEM available. Using x86 segment limits to approximate NX protection Entering add_active_range(0, 0, 180208) 0 entries of 256 used Zone PFN ranges: DMA 0 -> 4096 Normal 4096 -> 180208 HighMem 180208 -> 180208 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0 -> 180208 On node 0 totalpages: 180208 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 1376 pages used for memmap Normal zone: 174736 pages, LIFO batch:31 HighMem zone: 0 pages used for memmap Movable zone: 0 pages used for memmap DMI 2.3 present. Using APIC driver default ACPI: RSDP 000E5010, 0014 (r0 OID_00) ACPI: RSDT 2BFFCD40, 0030 (r1 INSYDE RSDT_000 1 _CSI 10101) ACPI: FACP 2BFFFA90, 0074 (r1 INSYDE FACP_000 100 _CSI 10101) ACPI: DSDT 2BFFCD80, 2D06 (r1 INSYDE Demo 1002 INTL 2002036) ACPI: FACS 2BFFFFC0, 0040 ACPI: APIC 2BFFFB20, 0068 (r1 INSYDE APIC_000 30303030 0000 30303030) ACPI: BOOT 2BFFFB90, 0028 (r1 INSYDE ISC_BOOT 100 _CSI 10101) ACPI: PM-Timer IO Port: 0x1008 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 1, version 20, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information Allocating PCI resources starting at 30000000 (gap: 2c000000:d3f80000) PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 SMP: Allowing 2 CPUs, 1 hotplug CPUs PERCPU: Allocating 41384 bytes of per cpu data NR_CPUS: 32, nr_cpu_ids: 2 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 178800 Kernel command line: ro root=/dev/VolGroup00/LogVol00 rhgb quiet mapped APIC to ffffb000 (fee00000) mapped IOAPIC to ffffa000 (fec00000) Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c07cb000 soft=c07ab000 PID hash table entries: 4096 (order: 12, 16384 bytes) Detected 2793.077 MHz processor. Console: colour VGA+ 80x25 console [tty0] enabled Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 705432k/720832k available (2254k kernel code, 14832k reserved, 1180k data, 284k init, 0k highmem) virtual kernel memory layout: fixmap : 0xffc53000 - 0xfffff000 (3760 kB) pkmap : 0xff400000 - 0xff800000 (4096 kB) vmalloc : 0xec800000 - 0xff3fe000 ( 299 MB) lowmem : 0xc0000000 - 0xebff0000 ( 703 MB) .init : 0xc0761000 - 0xc07a8000 ( 284 kB) .data : 0xc0633adf - 0xc075ab88 (1180 kB) .text : 0xc0400000 - 0xc0633adf (2254 kB) Checking if this processor honours the WP bit even in supervisor mode...Ok. CPA: page pool initialized 1 of 1 pages preallocated SLUB: Genslabs=12, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Calibrating delay using timer specific routine.. 5590.50 BogoMIPS (lpj=2795251) Security Framework initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 Initializing cgroup subsys ns Initializing cgroup subsys cpuacct Initializing cgroup subsys devices CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 128K CPU: Hyper-Threading is disabled Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU0: Thermal monitoring enabled Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code ACPI: Core revision 20080321 ENABLING IO-APIC IRQs ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1 CPU0: Intel(R) Celeron(R) CPU 2.80GHz stepping 09 Brought up 1 CPUs Total of 1 processors activated (5590.50 BogoMIPS). sizeof(vma)=84 bytes sizeof(page)=32 bytes sizeof(inode)=340 bytes sizeof(dentry)=132 bytes sizeof(ext3inode)=492 bytes sizeof(buffer_head)=56 bytes sizeof(skbuff)=180 bytes sizeof(task_struct)=3192 bytes CPU0 attaching sched-domain: domain 0: span 0 groups: 0 net_namespace: 660 bytes Booting paravirtualized kernel on bare hardware Time: 17:20:09 Date: 05/09/12 NET: Registered protocol family 16 No dock devices found. ACPI: bus type pci registered PCI: PCI BIOS revision 2.10 entry at 0xe8404, last bus=1 PCI: Using configuration type 1 for base access Setting up standard PCI resources ACPI: EC: Look up EC in DSDT ACPI: Interpreter enabled ACPI: (supports S0 S3 S4 S5) ACPI: Using IOAPIC for interrupt routing ACPI: EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62 ACPI: EC: driver started in poll mode ACPI: PCI Root Bridge [PCI0] (0000:00) pci 0000:00:02.0: Enabling SiS 96x SMBus ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.VPCI._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 5 6 10 *11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 5 6 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKC] (IRQs 3 5 6 *10 11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 5 6 10 *11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 5 6 10 11) *7 ACPI: PCI Interrupt Link [LNKF] (IRQs 3 *5 6 10 11) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 5 6 10 11) *0, disabled. ACPI: PCI Interrupt Link [LNKH] (IRQs *3 5 6 10 11) Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init ACPI: bus type pnp registered pnp: PnP ACPI: found 9 devices ACPI: ACPI bus type pnp unregistered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI: Using ACPI for IRQ routing NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default system 00:03: iomem range 0xfec00000-0xfec00fff has been reserved system 00:03: iomem range 0xfee00000-0xfee00fff has been reserved system 00:03: iomem range 0xffee0000-0xffefffff has been reserved system 00:03: iomem range 0xfffc0000-0xffffffff could not be reserved system 00:05: ioport range 0x480-0x48f has been reserved system 00:05: ioport range 0x1000-0x107f has been reserved system 00:05: ioport range 0x1080-0x10ff has been reserved PCI: Bridge: 0000:00:01.0 IO window: c000-dfff MEM window: 0xe0000000-0xefffffff PREFETCH window: 0x00000000a0000000-0x00000000afffffff PCI: Bus 2, cardbus bridge: 0000:00:09.0 IO window: 0x00001800-0x000018ff IO window: 0x00001c00-0x00001cff PREFETCH window: 0x30000000-0x33ffffff MEM window: 0x34000000-0x37ffffff ACPI: PCI Interrupt 0000:00:09.0[A] -> GSI 17 (level, low) -> IRQ 17 NET: Registered protocol family 2 IP route cache hash table entries: 32768 (order: 5, 131072 bytes) TCP established hash table entries: 131072 (order: 8, 1048576 bytes) TCP bind hash table entries: 65536 (order: 7, 524288 bytes) TCP: Hash tables configured (established 131072 bind 65536) TCP reno registered NET: Registered protocol family 1 checking if image is initramfs... it is Freeing initrd memory: 3661k freed Simple Boot Flag at 0x37 set to 0x1 apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) type=2000 audit(1336584008.504:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 1385 SELinux: Registering netfilter hooks ksign: Installing public key data Loading keyring - Added public key 42C60EC95A66A54 - User ID: Red Hat, Inc. (Kernel Module GPG key) Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pci 0000:01:00.0: Boot video device pci_hotplug: PCI Hot Plug PCI Core version: 0.5 input: Power Button (FF) as /class/input/input0 ACPI: Power Button (FF) [PWRF] input: Lid Switch as /class/input/input1 ACPI: Lid Switch [LID] input: Sleep Button (CM) as /class/input/input2 ACPI: Sleep Button (CM) [SLPB] ACPI: ACPI0007:00 is registered as cooling_device0 ACPI: Processor [CPU0] (supports 8 throttling states) isapnp: Scanning for PnP cards... Switched to high resolution mode on CPU 0 isapnp: No Plug & Play device found Real Time Clock Driver v1.12ac Non-volatile memory driver v1.2 Linux agpgart interface v0.103 agpgart: Detected SiS chipset - id:1633 agpgart: AGP aperture is 64M @ 0xf0000000 Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 18 ACPI: PCI interrupt for device 0000:00:02.6 disabled brd: module loaded input: Macintosh mouse button emulation as /class/input/input3 PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 i8042.c: Detected active multiplexing controller, rev 1.1. serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX0 port at 0x60,0x64 irq 12 serio: i8042 AUX1 port at 0x60,0x64 irq 12 serio: i8042 AUX2 port at 0x60,0x64 irq 12 serio: i8042 AUX3 port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice cpuidle: using governor ladder cpuidle: using governor menu usbcore: registered new interface driver hiddev usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 17 Using IPI No-Shortcut mode registered taskstats version 1 Magic number: 12:742:339 hash matches device ACPI0007:01 Freeing unused kernel memory: 284k freed Write protecting the kernel text: 2256k Write protecting the kernel read-only data: 960k input: AT Translated Set 2 keyboard as /class/input/input4 ACPI: PCI Interrupt 0000:00:03.3[D] -> GSI 23 (level, low) -> IRQ 23 ehci_hcd 0000:00:03.3: EHCI Host Controller ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1 PCI: cache line size of 128 is not supported by device 0000:00:03.3 ehci_hcd 0000:00:03.3: irq 23, io mem 0xf4002000 ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 6 ports detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: EHCI Host Controller usb usb1: Manufacturer: Linux 2.6.26.8-57.fc8 ehci_hcd usb usb1: SerialNumber: 0000:00:03.3 ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver ACPI: PCI Interrupt 0000:00:03.0[A] -> GSI 20 (level, low) -> IRQ 20 ohci_hcd 0000:00:03.0: OHCI Host Controller ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:03.0: irq 20, io mem 0xf4000000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 3 ports detected usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: OHCI Host Controller usb usb2: Manufacturer: Linux 2.6.26.8-57.fc8 ohci_hcd usb usb2: SerialNumber: 0000:00:03.0 ACPI: PCI Interrupt 0000:00:03.1[B] -> GSI 21 (level, low) -> IRQ 21 ohci_hcd 0000:00:03.1: OHCI Host Controller ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:03.1: irq 21, io mem 0xf4001000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 3 ports detected usb usb3: New USB device found, idVendor=1d6b, idProduct=0001 usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb3: Product: OHCI Host Controller usb usb3: Manufacturer: Linux 2.6.26.8-57.fc8 ohci_hcd usb usb3: SerialNumber: 0000:00:03.1 USB Universal Host Controller Interface driver v3.0 Synaptics Touchpad, model: 1, fw: 5.9, id: 0xf6eb3, caps: 0xa04713/0x0 input: SynPS/2 Synaptics TouchPad as /class/input/input5 SCSI subsystem initialized Driver 'sd' needs updating - please use bus_type methods libata version 3.00 loaded. pata_sis 0000:00:02.5: version 0.5.2 scsi0 : pata_sis scsi1 : pata_sis ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x1100 irq 14 ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1108 irq 15 ata1.00: ATA-6: IC25N040ATMR04-0, MO2OAD4A, max UDMA/100 ata1.00: 78140160 sectors, multi 16: LBA48 ata1.00: configured for UDMA/100 scsi 0:0:0:0: Direct-Access ATA IC25N040ATMR04-0 MO2O PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sd 0:0:0:0: [sda] Attached SCSI disk device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: 8192 avtab hash slots, 228192 rules. SELinux: 8192 avtab hash slots, 228192 rules. SELinux: 8 users, 12 roles, 2519 types, 116 bools, 1 sens, 1024 cats SELinux: 67 classes, 228192 rules SELinux: class peer not defined in policy SELinux: class capability2 not defined in policy SELinux: permission open in class dir not defined in policy SELinux: permission open in class file not defined in policy SELinux: permission open in class chr_file not defined in policy SELinux: permission open in class blk_file not defined in policy SELinux: permission open in class fifo_file not defined in policy SELinux: permission recvfrom in class node not defined in policy SELinux: permission sendto in class node not defined in policy SELinux: permission ingress in class netif not defined in policy SELinux: permission egress in class netif not defined in policy SELinux: permission setfcap in class capability not defined in policy SELinux: permission forward_in in class packet not defined in policy SELinux: permission forward_out in class packet not defined in policy SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev dm-0, type ext3), uses xattr SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts SELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts SELinux: policy loaded with handle_unknown=allow type=1403 audit(1336584017.825:2): policy loaded auid=4294967295 ses=4294967295 sd 0:0:0:0: Attached scsi generic sg0 type 0 ACPI: AC Adapter [AC] (on-line) sis96x_smbus 0000:00:02.1: SiS96x SMBus base address: 0x1400 ACPI: Battery Slot [BAT0] (battery absent) input: PC Speaker as /class/input/input6 sis900.c: v1.08.10 Apr. 2 2006 ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 19 (level, low) -> IRQ 19 0000:00:04.0: ICS LAN PHY transceiver found at address 1. 0000:00:04.0: Using transceiver found at address 1 as default eth0: SiS 900 PCI Fast Ethernet at 0xe400, IRQ 19, 00:40:d0:61:a2:9c Yenta: CardBus bridge found at 0000:00:09.0 [1631:c004] Yenta: Using CSCINT to route CSC interrupts to PCI Yenta: Routing CardBus interrupts to PCI Yenta TI: socket 0000:00:09.0, mfunc 0x01021002, devctl 0x64 Yenta: ISA IRQ mask 0x0cf8, PCI irq 17 Socket status: 30000006 udev: renamed network interface eth0 to eth1 ACPI: PCI Interrupt 0000:00:02.6[C] -> GSI 18 (level, low) -> IRQ 18 cs: IO port probe 0x100-0x3af: clean. cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7 cs: IO port probe 0x820-0x8ff: clean. cs: IO port probe 0xc00-0xcf7: clean. cs: IO port probe 0xa00-0xaff: clean. usbcore: registered new interface driver snd-usb-audio ACPI: PCI Interrupt 0000:00:02.7[C] -> GSI 18 (level, low) -> IRQ 18 intel8x0_measure_ac97_clock: measured 50445 usecs intel8x0: clocking to 48000 SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts NET: Registered protocol family 10 lo: Disabled Privacy Extensions ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16 device-mapper: multipath: version 1.0.5 loaded loop: module loaded EXT3 FS on dm-0, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. SELinux: initialized (dev sda2, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs fuse init (API version 7.9) SELinux: initialized (dev sda1, type fuseblk), uses genfs_contexts type=1400 audit(1336580454.864:3): avc: denied { getattr } for pid=1364 comm="pam_console_app" path="/dev/fb0" dev=tmpfs ino=5182 scontext=system_u:system_r:pam_console_t:s0 tcontext=system_u:object_r:device_t:s0 tclass=file type=1400 audit(1336580454.864:4): avc: denied { setattr } for pid=1364 comm="pam_console_app" name="fb0" dev=tmpfs ino=5182 scontext=system_u:system_r:pam_console_t:s0 tcontext=system_u:object_r:device_t:s0 tclass=file Adding 1441784k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-1 extents:1 across:1441784k SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts firmware: requesting intel-ucode/0f-02-09 IA-32 Microcode Update Driver: v1.14a microcode: CPU0 updated from revision 0x17 to 0x2e, date = 08112004 warning: process `kudzu' used the deprecated sysctl system call with 1.23. ip_tables: (C) 2000-2006 Netfilter Core Team nf_conntrack version 0.5.0 (11264 buckets, 45056 max) RPC: Registered udp transport module. RPC: Registered tcp transport module. SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts warning: `dbus-daemon' uses 32-bit capabilities (legacy support in use) vboxdrv: Found 1 processor cores. vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. vboxdrv: Successfully loaded version 4.1.2 (interface 0x00190000). vboxpci: pci-stub module not available, cannot detach PCI devices vboxpci: IOMMU not found (not compiled) Installing knfsd (copyright (C) 1996 okir@monad.swb.de). SELinux: initialized (dev nfsd, type nfsd), uses genfs_contexts NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period eth1: Media Link Off ADDRCONF(NETDEV_UP): eth1: link is not ready usb 1-6: new high speed USB device using ehci_hcd and address 2 usb 1-6: configuration #1 chosen from 1 choice usb 1-6: New USB device found, idVendor=12d1, idProduct=1003 usb 1-6: New USB device strings: Mfr=2, Product=1, SerialNumber=0 usb 1-6: Product: HUAWEI Mobile usb 1-6: Manufacturer: HUAWEI Technology Initializing USB Mass Storage driver... usb 1-6: USB disconnect, address 2 scsi2 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 2 usb-storage: waiting for device to settle before scanning usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usb 1-6: new high speed USB device using ehci_hcd and address 3 usb 1-6: configuration #1 chosen from 1 choice usb-storage: probe of 1-6:1.0 failed with error -5 usb-storage: probe of 1-6:1.1 failed with error -5 scsi5 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning scsi6 : SCSI emulation for USB Mass Storage devices usb 1-6: New USB device found, idVendor=12d1, idProduct=1003 usb 1-6: New USB device strings: Mfr=2, Product=1, SerialNumber=0 usb 1-6: Product: HUAWEI Mobile usb 1-6: Manufacturer: HUAWEI Technology usbcore: registered new interface driver usbserial usbserial: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core usb-storage: device found at 3 usb-storage: waiting for device to settle before scanning usbserial: USB Serial support registered for GSM modem (1-port) option 1-6:1.0: GSM modem (1-port) converter detected usb 1-6: GSM modem (1-port) converter now attached to ttyUSB0 option 1-6:1.1: GSM modem (1-port) converter detected usb 1-6: GSM modem (1-port) converter now attached to ttyUSB1 usbcore: registered new interface driver option option: USB Driver for GSM modems: v0.7.2 usb-storage: device scan complete scsi 5:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 scsi 5:0:0:0: Attached scsi generic sg1 type 5 Driver 'sr' needs updating - please use bus_type methods sr0: scsi-1 drive Uniform CD-ROM driver Revision: 3.20 sr 5:0:0:0: Attached scsi CD-ROM sr0 usb-storage: device scan complete scsi 6:0:0:0: Direct-Access HUAWEI MMC Storage 2.31 PQ: 0 ANSI: 2 sd 6:0:0:0: [sdb] Attached SCSI removable disk sd 6:0:0:0: Attached scsi generic sg2 type 0 PPP generic driver version 2.4.2 PPP Deflate Compression module registered