[ 0.000000] Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007 (Ubuntu 2.6.22-14.46-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved) [ 0.000000] BIOS-e820: 00000000000dc000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000002f6f0000 (usable) [ 0.000000] BIOS-e820: 000000002f6f0000 - 000000002f6fb000 (ACPI data) [ 0.000000] BIOS-e820: 000000002f6fb000 - 000000002f700000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000002f700000 - 0000000030000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec10000 - 00000000fec20000 (reserved) [ 0.000000] BIOS-e820: 00000000ffb00000 - 00000000ffc00000 (reserved) [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) [ 0.000000] 0MB HIGHMEM available. [ 0.000000] 758MB LOWMEM available. [ 0.000000] Entering add_active_range(0, 0, 194288) 0 entries of 256 used [ 0.000000] Zone PFN ranges: [ 0.000000] DMA 0 -> 4096 [ 0.000000] Normal 4096 -> 194288 [ 0.000000] HighMem 194288 -> 194288 [ 0.000000] early_node_map[1] active PFN ranges [ 0.000000] 0: 0 -> 194288 [ 0.000000] On node 0 totalpages: 194288 [ 0.000000] DMA zone: 32 pages used for memmap [ 0.000000] DMA zone: 0 pages reserved [ 0.000000] DMA zone: 4064 pages, LIFO batch:0 [ 0.000000] Normal zone: 1485 pages used for memmap [ 0.000000] Normal zone: 188707 pages, LIFO batch:31 [ 0.000000] HighMem zone: 0 pages used for memmap [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP signature @ 0xC00F5BC0 checksum 0 [ 0.000000] ACPI: RSDP 000F5BC0, 0014 (r0 FUJ ) [ 0.000000] ACPI: RSDT 2F6F4CFB, 0030 (r1 FUJ FJNB182 1130000 FUJ 100) [ 0.000000] ACPI: FACP 2F6FAF8C, 0074 (r1 FUJ FJNB182 1130000 FUJ 100) [ 0.000000] ACPI: DSDT 2F6F4D2B, 5FFA (r1 FUJ FJNB182 1130000 MSFT 100000E) [ 0.000000] ACPI: FACS 2F6FBFC0, 0040 [ 0.000000] ACPI: SSDT 2F6FAD25, 023F (r1 FUJ FJNB182 1130000 MSFT 100000E) [ 0.000000] ACPI: BOOT 2F6FAF64, 0028 (r1 FUJ FJNB182 1130000 FUJ 100) [ 0.000000] ACPI: PM-Timer IO Port: 0xfc08 [ 0.000000] Allocating PCI resources starting at 40000000 (gap: 30000000:cec10000) [ 0.000000] Built 1 zonelists. Total pages: 192771 [ 0.000000] Kernel command line: BOOT_IMAGE=/casper/vmlinuz file=/cdrom/preseed/kubuntu.seed boot=casper initrd=/casper/initrd.gz quiet splash -- locale=cs_CZ [ 0.000000] Local APIC disabled by BIOS -- you can enable it with "lapic" [ 0.000000] mapped APIC to ffffd000 (015fe000) [ 0.000000] Enabling fast FPU save and restore... done. [ 0.000000] Enabling unmasked SIMD FPU exception support... done. [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes) [ 0.000000] Detected 1299.979 MHz processor. [ 52.591948] Console: colour VGA+ 80x25 [ 52.592325] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 52.592885] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 52.623059] Memory: 758412k/777152k available (2015k kernel code, 18072k reserved, 916k data, 364k init, 0k highmem) [ 52.623072] virtual kernel memory layout: [ 52.623073] fixmap : 0xfff4d000 - 0xfffff000 ( 712 kB) [ 52.623075] pkmap : 0xff800000 - 0xffc00000 (4096 kB) [ 52.623077] vmalloc : 0xf0000000 - 0xff7fe000 ( 247 MB) [ 52.623078] lowmem : 0xc0000000 - 0xef6f0000 ( 758 MB) [ 52.623080] .init : 0xc03e3000 - 0xc043e000 ( 364 kB) [ 52.623082] .data : 0xc02f7d26 - 0xc03dce84 ( 916 kB) [ 52.623083] .text : 0xc0100000 - 0xc02f7d26 (2015 kB) [ 52.623088] Checking if this processor honours the WP bit even in supervisor mode... Ok. [ 52.623137] SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1 [ 52.703091] Calibrating delay using timer specific routine.. 2604.01 BogoMIPS (lpj=5208029) [ 52.703126] Security Framework v1.0.0 initialized [ 52.703136] SELinux: Disabled at boot. [ 52.703154] Mount-cache hash table entries: 512 [ 52.703311] CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 00000000 00000000 00000000 [ 52.703326] CPU: L1 I cache: 32K, L1 D cache: 32K [ 52.703329] CPU: L2 cache: 1024K [ 52.703333] CPU: After all inits, caps: afe9f9bf 00000000 00000000 00002040 00000000 00000000 00000000 [ 52.703344] Compat vDSO mapped to ffffe000. [ 52.703358] Checking 'hlt' instruction... OK. [ 52.719198] SMP alternatives: switching to UP code [ 52.719414] Freeing SMP alternatives: 11k freed [ 52.719744] Early unpacking initramfs... done [ 53.180104] ACPI: Core revision 20070126 [ 53.180201] ACPI: Looking for DSDT in initramfs... error, file /DSDT.aml not found. [ 53.183296] ACPI: setting ELCR to 0200 (from 0800) [ 53.188120] CPU0: Intel(R) Celeron(R) M processor 1.30GHz stepping 06 [ 53.188131] SMP motherboard not detected. [ 53.188134] Local APIC not detected. Using dummy APIC emulation. [ 53.188177] Brought up 1 CPUs [ 53.188323] Booting paravirtualized kernel on bare hardware [ 53.188392] Time: 10:25:18 Date: 07/16/108 [ 53.188423] NET: Registered protocol family 16 [ 53.188528] EISA bus registered [ 53.188542] ACPI: bus type pci registered [ 53.188716] PCI: PCI BIOS revision 2.10 entry at 0xfd972, last bus=3 [ 53.188719] PCI: Using configuration type 1 [ 53.188722] Setting up standard PCI resources [ 53.191510] ACPI: EC: Look up EC in DSDT [ 53.199413] ACPI: Interpreter enabled [ 53.199417] ACPI: (supports S0 S3 S4 S5) [ 53.199441] ACPI: Using PIC for interrupt routing [ 53.208481] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 53.208498] PCI: Probing PCI hardware (bus 00) [ 53.208954] PCI quirk: region fc00-fc7f claimed by ICH4 ACPI/GPIO/TCO [ 53.208958] PCI quirk: region fc80-fcbf claimed by ICH4 GPIO [ 53.209379] PCI: Transparent bridge - 0000:00:1e.0 [ 53.209508] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 53.209612] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT] [ 53.212098] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11) [ 53.212254] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11) [ 53.212407] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11) [ 53.212560] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11) [ 53.212713] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11) [ 53.212865] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 *11) [ 53.213018] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11) *0, disabled. [ 53.213172] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11) [ 53.213298] Linux Plug and Play Support v0.97 (c) Adam Belay [ 53.213310] pnp: PnP ACPI init [ 53.213319] ACPI: bus type pnp registered [ 53.218244] pnp: PnP ACPI: found 11 devices [ 53.218248] ACPI: ACPI bus type pnp unregistered [ 53.218254] PnPBIOS: Disabled by ACPI PNP [ 53.218314] PCI: Using ACPI for IRQ routing [ 53.218317] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 53.224617] NET: Registered protocol family 8 [ 53.224619] NET: Registered protocol family 20 [ 53.224697] pnp: 00:01: iomem range 0xcd400-0xcffff could not be reserved [ 53.224702] pnp: 00:01: iomem range 0xffb00000-0xffbfffff could not be reserved [ 53.224707] pnp: 00:01: iomem range 0xfec10000-0xfec1ffff could not be reserved [ 53.226645] Time: tsc clocksource has been installed. [ 53.255044] PCI: Bus 2, cardbus bridge: 0000:01:0a.0 [ 53.255047] IO window: 00003000-000030ff [ 53.255052] IO window: 00003400-000034ff [ 53.255056] PREFETCH window: 40000000-43ffffff [ 53.255061] MEM window: 4c000000-4fffffff [ 53.255066] PCI: Bus 3, cardbus bridge: 0000:01:0a.1 [ 53.255068] IO window: 00003800-000038ff [ 53.255073] IO window: 00003c00-00003cff [ 53.255077] PREFETCH window: 44000000-47ffffff [ 53.255082] MEM window: 50000000-53ffffff [ 53.255086] PCI: Bridge: 0000:00:1e.0 [ 53.255090] IO window: 3000-3fff [ 53.255095] MEM window: d0200000-d02fffff [ 53.255100] PREFETCH window: 40000000-47ffffff [ 53.255113] PCI: Setting latency timer of device 0000:00:1e.0 to 64 [ 53.255317] ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11 [ 53.255320] PCI: setting IRQ 11 as level-triggered [ 53.255324] ACPI: PCI Interrupt 0000:01:0a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 53.255503] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 [ 53.255506] ACPI: PCI Interrupt 0000:01:0a.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 [ 53.255524] NET: Registered protocol family 2 [ 53.294630] IP route cache hash table entries: 32768 (order: 5, 131072 bytes) [ 53.294719] TCP established hash table entries: 131072 (order: 8, 1572864 bytes) [ 53.297408] TCP bind hash table entries: 65536 (order: 7, 524288 bytes) [ 53.298540] TCP: Hash tables configured (established 131072 bind 65536) [ 53.298546] TCP reno registered [ 53.306818] checking if image is initramfs... it is [ 53.758219] Switched to high resolution mode on CPU 0 [ 54.209836] Freeing initrd memory: 7313k freed [ 54.210038] Simple Boot Flag at 0x7f set to 0x1 [ 54.210307] audit: initializing netlink socket (disabled) [ 54.210329] audit(1218882318.108:1): initialized [ 54.212719] VFS: Disk quotas dquot_6.5.1 [ 54.212780] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 54.212895] io scheduler noop registered [ 54.212899] io scheduler anticipatory registered [ 54.212901] io scheduler deadline registered [ 54.212921] io scheduler cfq registered (default) [ 54.212942] Boot video device is 0000:00:02.0 [ 54.213194] isapnp: Scanning for PnP cards... [ 54.567045] isapnp: No Plug & Play device found [ 54.602052] Real Time Clock Driver v1.12ac [ 54.602195] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 54.602309] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 54.602531] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 54.603327] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 54.603586] ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 [ 54.603596] ACPI: PCI interrupt for device 0000:00:1f.6 disabled [ 54.604246] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 54.604518] input: Macintosh mouse button emulation as /class/input/input0 [ 54.604617] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 54.607793] i8042.c: Detected active multiplexing controller, rev 1.1. [ 54.609523] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 54.609531] serio: i8042 AUX0 port at 0x60,0x64 irq 12 [ 54.609535] serio: i8042 AUX1 port at 0x60,0x64 irq 12 [ 54.609538] serio: i8042 AUX2 port at 0x60,0x64 irq 12 [ 54.609541] serio: i8042 AUX3 port at 0x60,0x64 irq 12 [ 54.609770] mice: PS/2 mouse device common for all mice [ 54.610003] EISA: Probing bus 0 at eisa.0 [ 54.610014] Cannot allocate resource for EISA slot 1 [ 54.610017] Cannot allocate resource for EISA slot 2 [ 54.610020] Cannot allocate resource for EISA slot 3 [ 54.610043] EISA: Detected 0 cards. [ 54.610177] TCP cubic registered [ 54.610197] NET: Registered protocol family 1 [ 54.610232] Using IPI No-Shortcut mode [ 54.610457] Magic number: 4:647:426 [ 54.610904] Freeing unused kernel memory: 364k freed [ 54.708036] input: AT Translated Set 2 keyboard as /class/input/input1 [ 55.856522] AppArmor: AppArmor initialized<5>audit(1218882320.108:2): type=1505 info="AppArmor initialized" pid=1203 [ 55.866893] fuse init (API version 7.8) [ 55.873760] Failure registering capabilities with primary security module. [ 55.891819] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) [ 56.457682] usbcore: registered new interface driver usbfs [ 56.457714] usbcore: registered new interface driver hub [ 56.457739] usbcore: registered new device driver usb [ 56.458789] USB Universal Host Controller Interface driver v3.0 [ 56.458877] ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 56.458892] PCI: Setting latency timer of device 0000:00:1d.0 to 64 [ 56.458897] uhci_hcd 0000:00:1d.0: UHCI Host Controller [ 56.459158] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1 [ 56.459184] uhci_hcd 0000:00:1d.0: irq 11, io base 0x000020c0 [ 56.459327] usb usb1: configuration #1 chosen from 1 choice [ 56.459361] hub 1-0:1.0: USB hub found [ 56.459367] hub 1-0:1.0: 2 ports detected [ 56.559910] ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 [ 56.559917] ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11 [ 56.559932] PCI: Setting latency timer of device 0000:00:1d.1 to 64 [ 56.559936] uhci_hcd 0000:00:1d.1: UHCI Host Controller [ 56.559969] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2 [ 56.559995] uhci_hcd 0000:00:1d.1: irq 11, io base 0x000020e0 [ 56.560116] usb usb2: configuration #1 chosen from 1 choice [ 56.560149] hub 2-0:1.0: USB hub found [ 56.560157] hub 2-0:1.0: 2 ports detected [ 56.622198] SCSI subsystem initialized [ 56.629185] libata version 2.21 loaded. [ 56.663807] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11 [ 56.663814] ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 [ 56.663828] PCI: Setting latency timer of device 0000:00:1d.2 to 64 [ 56.663832] uhci_hcd 0000:00:1d.2: UHCI Host Controller [ 56.663865] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3 [ 56.663891] uhci_hcd 0000:00:1d.2: irq 11, io base 0x00002400 [ 56.664008] usb usb3: configuration #1 chosen from 1 choice [ 56.664048] hub 3-0:1.0: USB hub found [ 56.664055] hub 3-0:1.0: 2 ports detected [ 56.768223] ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11 [ 56.768229] ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11 [ 56.768245] PCI: Setting latency timer of device 0000:00:1d.7 to 64 [ 56.768250] ehci_hcd 0000:00:1d.7: EHCI Host Controller [ 56.768297] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4 [ 56.768333] ehci_hcd 0000:00:1d.7: debug port 1 [ 56.768340] PCI: cache line size of 32 is not supported by device 0000:00:1d.7 [ 56.768350] ehci_hcd 0000:00:1d.7: irq 11, io mem 0xd0100000 [ 56.772832] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 56.772934] usb usb4: configuration #1 chosen from 1 choice [ 56.772971] hub 4-0:1.0: USB hub found [ 56.772980] hub 4-0:1.0: 6 ports detected [ 56.875645] tg3.c:v3.77 (May 31, 2007) [ 56.875916] ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 11 [ 56.875920] ACPI: PCI Interrupt 0000:01:0c.0[A] -> Link [LNKE] -> GSI 11 (level, low) -> IRQ 11 [ 56.918203] eth0: Tigon3 [partno(BCM95788MT58) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000Base-T Ethernet 00:17:42:91:71:a6 [ 56.918213] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[0] TSOcap[1] [ 56.918217] eth0: dma_rwctrl[763f0000] dma_mask[64-bit] [ 56.918502] ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11 [ 56.918508] ACPI: PCI Interrupt 0000:01:0e.0[A] -> Link [LNKF] -> GSI 11 (level, low) -> IRQ 11 [ 56.970265] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[11] MMIO=[d0215000-d02157ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 56.978092] ata_piix 0000:00:1f.1: version 2.11 [ 56.978118] ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 [ 56.978158] PCI: Setting latency timer of device 0000:00:1f.1 to 64 [ 56.978259] scsi0 : ata_piix [ 56.978316] scsi1 : ata_piix [ 56.979193] ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x00012440 irq 14 [ 56.979197] ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x00012448 irq 15 [ 4.448000] Marking TSC unstable due to: possible TSC halt in C2. [ 4.472000] Time: acpi_pm clocksource has been installed. [ 4.528000] ata1.00: ATA-5: TOSHIBA MK4021GAS, GA224G, max UDMA/100 [ 4.528000] ata1.00: 78140160 sectors, multi 16: LBA [ 4.536000] ata1.00: configured for UDMA/100 [ 5.012000] ata2.00: ATAPI: UJDA750FDVD/CDRW, 1.20, max UDMA/33 [ 5.200000] ata2.00: configured for UDMA/33 [ 5.200000] scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4021GA GA22 PQ: 0 ANSI: 5 [ 5.216000] scsi 1:0:0:0: CD-ROM MATSHITA UJDA750FDVD/CDRW 1.20 PQ: 0 ANSI: 5 [ 5.232000] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB) [ 5.232000] sd 0:0:0:0: [sda] Write Protect is off [ 5.232000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.232000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.232000] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB) [ 5.232000] sd 0:0:0:0: [sda] Write Protect is off [ 5.232000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.232000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.232000] sda:<7>ieee1394: Host added: ID:BUS[0-00:1023] GUID[00000e1003f5e769] [ 5.668000] sda1 sda2 sda3 [ 5.972000] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.976000] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 5.976000] sr 1:0:0:0: Attached scsi generic sg1 type 5 [ 5.992000] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray [ 5.992000] Uniform CD-ROM driver Revision: 3.20 [ 5.992000] sr 1:0:0:0: Attached scsi CD-ROM sr0 [ 6.912000] ISO 9660 Extensions: Microsoft Joliet Level 3 [ 6.944000] ISO 9660 Extensions: RRIP_1991A [ 7.224000] Registering unionfs 1.4 [ 7.224000] unionfs: debugging is not enabled [ 7.240000] loop: module loaded [ 10.332000] squashfs: version 3.2-UBUNTU (2007/07/26) Phillip Lougher [ 81.136000] Clocksource tsc unstable (delta = -417828710 ns) [ 83.420000] Linux agpgart interface v0.102 (c) Dave Jones [ 83.532000] agpgart: Detected an Intel 855GM Chipset. [ 83.532000] agpgart: Detected 8060K stolen memory. [ 83.540000] agpgart: AGP aperture is 128M @ 0xd8000000 [ 83.956000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 84.188000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 84.296000] iTCO_vendor_support: vendor-support=0 [ 84.300000] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (21-Jan-2007) [ 84.300000] iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0xfc60) [ 84.300000] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) [ 84.412000] intel_rng: FWH not detected [ 85.800000] input: PC Speaker as /class/input/input2 [ 85.884000] ieee80211_crypt: registered algorithm 'NULL' [ 85.888000] ieee80211: 802.11 data/management/control stack, git-1.1.13 [ 85.888000] ieee80211: Copyright (C) 2004-2005 Intel Corporation [ 85.960000] ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2 [ 85.960000] ipw2100: Copyright(c) 2003-2006 Intel Corporation [ 85.960000] ACPI: PCI Interrupt 0000:01:0d.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11 [ 85.960000] ipw2100: Detected Intel PRO/Wireless 2100 Network Connection [ 86.332000] irda_init() [ 86.332000] NET: Registered protocol family 23 [ 86.720000] input: PS/2 Generic Mouse as /class/input/input3 [ 86.720000] parport_pc 00:0a: reported by Plug and Play ACPI [ 86.720000] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP] [ 86.724000] found SMC SuperIO Chip (devid=0x7a rev=00 base=0x002e): LPC47N227 [ 86.724000] smsc_superio_flat(): fir: 0x400, sir: 0x2f8, dma: 01, irq: 3, mode: 0x0e [ 86.724000] smsc_ircc_present: can't get sir_base of 0x2f8 [ 86.876000] eth1: Radio is disabled by RF switch. [ 87.020000] Yenta: CardBus bridge found at 0000:01:0a.0 [10cf:10e6] [ 87.020000] Yenta O2: res at 0x94/0xD4: ea/00 [ 87.020000] Yenta O2: enabling read prefetch/write burst [ 87.148000] Yenta: ISA IRQ mask 0x0438, PCI irq 11 [ 87.148000] Socket status: 30000006 [ 87.148000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff [ 87.148000] cs: IO port probe 0x3000-0x3fff: clean. [ 87.148000] pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff [ 87.148000] pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x47ffffff [ 87.148000] Yenta: CardBus bridge found at 0000:01:0a.1 [10cf:10e6] [ 87.276000] Yenta: ISA IRQ mask 0x0438, PCI irq 11 [ 87.276000] Socket status: 30000006 [ 87.276000] Yenta: Raising subordinate bus# of parent bus (#01) from #03 to #06 [ 87.276000] pcmcia: parent PCI bridge I/O window: 0x3000 - 0x3fff [ 87.276000] cs: IO port probe 0x3000-0x3fff: clean. [ 87.276000] pcmcia: parent PCI bridge Memory window: 0xd0200000 - 0xd02fffff [ 87.276000] pcmcia: parent PCI bridge Memory window: 0x40000000 - 0x47ffffff [ 87.292000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11 [ 87.292000] PCI: Setting latency timer of device 0000:00:1f.5 to 64 [ 88.072000] cs: IO port probe 0x100-0x3af: clean. [ 88.076000] cs: IO port probe 0x3e0-0x4ff: excluding 0x400-0x407 0x4d0-0x4d7 [ 88.076000] cs: IO port probe 0x820-0x8ff: clean. [ 88.076000] cs: IO port probe 0xc00-0xcf7: clean. [ 88.076000] cs: IO port probe 0xa00-0xaff: clean. [ 88.080000] cs: IO port probe 0x100-0x3af: clean. [ 88.080000] cs: IO port probe 0x3e0-0x4ff: excluding 0x400-0x407 0x4d0-0x4d7 [ 88.080000] cs: IO port probe 0x820-0x8ff: clean. [ 88.080000] cs: IO port probe 0xc00-0xcf7: clean. [ 88.084000] cs: IO port probe 0xa00-0xaff: clean. [ 88.120000] intel8x0_measure_ac97_clock: measured 55426 usecs [ 88.120000] intel8x0: clocking to 48000 [ 107.384000] Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k [ 110.800000] ACPI: AC Adapter [AC] (on-line) [ 110.872000] ACPI: Battery Slot [CMB1] (battery present) [ 110.872000] ACPI: Battery Slot [CMB2] (battery absent) [ 110.920000] ACPI: ACPI Dock Station Driver [ 110.924000] ACPI: \_SB_.PCI0.IDE_.SECN.MAST: found ejectable bay [ 110.924000] ACPI: \_SB_.PCI0.IDE_.SECN.MAST: Adding notify handler [ 110.924000] ACPI: Error installing bay notify handler [ 110.924000] ACPI: Bay [\_SB_.PCI0.IDE_.SECN.MAST] Added [ 111.012000] input: Power Button (FF) as /class/input/input4 [ 111.016000] ACPI: Power Button (FF) [PWRF] [ 111.080000] input: Power Button (CM) as /class/input/input5 [ 111.084000] ACPI: Power Button (CM) [PWRB] [ 111.140000] input: Lid Switch as /class/input/input6 [ 111.140000] ACPI: Lid Switch [LID] [ 111.300000] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) [ 118.472000] PM: Writing back config space on device 0000:01:0c.0 at offset c (was dfff0000, writing 0) [ 118.472000] PM: Writing back config space on device 0000:01:0c.0 at offset b (was 165d14e4, writing 127910cf) [ 118.472000] PM: Writing back config space on device 0000:01:0c.0 at offset 3 (was 0, writing 4008) [ 118.472000] PM: Writing back config space on device 0000:01:0c.0 at offset 2 (was 2000000, writing 2000003) [ 118.472000] PM: Writing back config space on device 0000:01:0c.0 at offset 1 (was 2b00000, writing 2b00106) [ 118.472000] PM: Writing back config space on device 0000:01:0c.0 at offset 0 (was 165d14e4, writing 165e14e4) [ 120.352000] tg3: eth0: Link is up at 100 Mbps, full duplex. [ 120.352000] tg3: eth0: Flow control is on for TX and on for RX. [ 122.488000] lp0: using parport0 (interrupt-driven). [ 122.604000] ppdev: user-space parallel port driver [ 127.612000] apm: BIOS not found. [ 130.228000] [drm] Initialized drm 1.1.0 20060810 [ 130.292000] ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11 [ 130.292000] [drm] Initialized i915 1.6.0 20060119 on minor 0 [ 130.292000] [drm] Initialized i915 1.6.0 20060119 on minor 1 [ 132.856000] Failure registering capabilities with primary security module. [ 134.624000] Bluetooth: Core ver 2.11 [ 134.624000] NET: Registered protocol family 31 [ 134.624000] Bluetooth: HCI device and connection manager initialized [ 134.624000] Bluetooth: HCI socket layer initialized [ 134.812000] Bluetooth: L2CAP ver 2.8 [ 134.812000] Bluetooth: L2CAP socket layer initialized [ 134.844000] Bluetooth: RFCOMM socket layer initialized [ 134.844000] Bluetooth: RFCOMM TTY layer initialized [ 134.844000] Bluetooth: RFCOMM ver 1.8 [ 141.548000] NET: Registered protocol family 17 [ 153.084000] NET: Registered protocol family 10 [ 153.084000] lo: Disabled Privacy Extensions [ 153.084000] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 163.592000] eth0: no IPv6 routers present [ 1568.492000] ReiserFS: sda3: found reiserfs format "3.6" with standard journal [ 1568.492000] ReiserFS: sda3: using ordered data mode [ 1573.008000] ReiserFS: sda3: journal params: device sda3, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30 [ 1573.008000] ReiserFS: sda3: checking transaction log (sda3) [ 1617.996000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen [ 1617.996000] ata1.00: cmd c8/00:00:8f:7a:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 131072 in [ 1617.996000] res 40/00:00:06:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1623.036000] ata1: port is slow to respond, please be patient (Status 0xd0) [ 1628.020000] ata1: device not ready (errno=-16), forcing hardreset [ 1628.020000] ata1: soft resetting port [ 1628.200000] ata1.00: configured for UDMA/100 [ 1628.200000] ata1: EH complete [ 1631.436000] sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB) [ 1631.436000] sd 0:0:0:0: [sda] Write Protect is off [ 1631.436000] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 1631.816000] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 1661.884000] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen [ 1661.884000] ata1.00: cmd c8/00:00:e7:7b:00/00:00:00:00:00/e0 tag 0 cdb 0x0 data 131072 in [ 1661.884000] res 40/00:00:06:4f:c2/00:00:00:00:00/00 Emask 0x4 (timeout) [ 1666.924000] ata1: port is slow to respond, please be patient (Status 0xd0) [ 1671.908000] ata1: device not ready (errno=-16), forcing hardreset [ 1671.908000] ata1: soft resetting port [ 1702.148000] ata1.00: qc timeout (cmd 0xec) [ 1702.148000] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 1702.148000] ata1.00: revalidation failed (errno=-5) [ 1702.148000] ata1: failed to recover some devices, retrying in 5 secs [ 1712.192000] ata1: port is slow to respond, please be patient (Status 0xd0) [ 1717.176000] ata1: device not ready (errno=-16), forcing hardreset [ 1717.176000] ata1: soft resetting port [ 1747.416000] ata1.00: qc timeout (cmd 0xec) [ 1747.416000] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 1747.416000] ata1.00: revalidation failed (errno=-5) [ 1747.416000] ata1.00: limiting speed to UDMA/100:PIO3 [ 1747.416000] ata1: failed to recover some devices, retrying in 5 secs [ 1757.460000] ata1: port is slow to respond, please be patient (Status 0xd0) [ 1762.444000] ata1: device not ready (errno=-16), forcing hardreset [ 1762.444000] ata1: soft resetting port [ 1792.684000] ata1.00: qc timeout (cmd 0xec) [ 1792.684000] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4) [ 1792.684000] ata1.00: revalidation failed (errno=-5) [ 1792.684000] ata1.00: disabled [ 1793.188000] ata1: EH complete [ 1793.192000] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 1793.192000] end_request: I/O error, dev sda, sector 31719 [ 1793.192000] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 1793.192000] end_request: I/O error, dev sda, sector 31975 [ 1793.192000] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 1793.192000] end_request: I/O error, dev sda, sector 32231 [ 1793.192000] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 1793.192000] end_request: I/O error, dev sda, sector 32487 [ 1793.192000] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 1793.192000] end_request: I/O error, dev sda, sector 32495 [ 1793.192000] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 1793.192000] end_request: I/O error, dev sda, sector 32751 [ 1793.192000] sd 0:0:0:0: [sda] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK,SUGGEST_OK [ 1793.192000] end_request: I/O error, dev sda, sector 33007 [ 1793.232000] ReiserFS: sda3: warning: journal-1212: REPLAY FAILURE fsck required! buffer write failed [ 1793.232000] ReiserFS: sda3: warning: Replay Failure, unable to mount [ 1793.232000] ReiserFS: sda3: warning: sh-2022: reiserfs_fill_super: unable to initialize journal space