smartctl 5.42 2011-10-20 r3458 [x86_64-linux-3.4.6-2.10-desktop] (SUSE RPM) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Device Model: ST500DM002-1BD142 Serial Number: Z2AQZKEG LU WWN Device Id: 5 000c50 04065d095 Firmware Version: KC45 User Capacity: 500 107 862 016 bytes [500 GB] Sector Sizes: 512 bytes logical, 4096 bytes physical Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Thu Sep 13 20:08:24 2012 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 609) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 87) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-- 104 077 006 - 6953096 3 Spin_Up_Time PO---- 100 100 000 - 0 4 Start_Stop_Count -O--CK 100 100 020 - 70 5 Reallocated_Sector_Ct PO--CK 095 095 036 - 1736 7 Seek_Error_Rate POSR-- 060 060 030 - 1017525 9 Power_On_Hours -O--CK 100 100 000 - 54 10 Spin_Retry_Count PO--C- 100 100 097 - 0 12 Power_Cycle_Count -O--CK 100 100 020 - 70 183 Runtime_Bad_Block -O--CK 100 100 000 - 0 184 End-to-End_Error -O--CK 100 100 099 - 0 187 Reported_Uncorrect -O--CK 001 001 000 - 852 188 Command_Timeout -O--CK 100 100 000 - 0 189 High_Fly_Writes -O-RCK 100 100 000 - 0 190 Airflow_Temperature_Cel -O---K 071 055 045 - 29 (Min/Max 20/29) 194 Temperature_Celsius -O---K 029 045 000 - 29 (0 19 0 0 0) 195 Hardware_ECC_Recovered -O-RC- 047 037 000 - 6953096 197 Current_Pending_Sector -O--C- 099 098 000 - 80 198 Offline_Uncorrectable ----C- 099 098 000 - 80 199 UDMA_CRC_Error_Count -OSRCK 200 200 000 - 0 240 Head_Flying_Hours ------ 100 253 000 - 269573622333494 241 Total_LBAs_Written ------ 100 253 000 - 192172717 242 Total_LBAs_Read ------ 100 253 000 - 58705692 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 5 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error log] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP Log at address 0x21 has 1 sectors [Write stream error log] GP Log at address 0x22 has 1 sectors [Read stream error log] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa1 has 20 sectors [Device vendor specific log] GP Log at address 0xa2 has 2248 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 129 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP Log at address 0xab has 1 sectors [Device vendor specific log] GP Log at address 0xb0 has 2928 sectors [Device vendor specific log] GP Log at address 0xbd has 252 sectors [Device vendor specific log] GP Log at address 0xbe has 65535 sectors [Device vendor specific log] GP Log at address 0xbf has 65535 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (5 sectors) Device Error Count: 715 (device log contains only the most recent 20 errors) CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 715 [14] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 f0 00 00 01 c0 46 18 e1 00 00:01:55.810 READ DMA c8 00 00 00 08 00 00 01 c0 46 10 e1 00 00:01:55.808 READ DMA c8 00 00 00 08 00 00 01 c0 46 08 e1 00 00:01:55.801 READ DMA c8 00 00 00 08 00 00 01 c4 fd 08 e1 00 00:01:55.801 READ DMA c8 00 00 00 08 00 00 01 c4 fd 10 e1 00 00:01:55.801 READ DMA Error 714 [13] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 01 c0 46 78 e1 00 00:01:50.156 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:50.155 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:50.152 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:50.150 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:50.128 READ NATIVE MAX ADDRESS EXT Error 713 [12] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 01 c0 46 78 e1 00 00:01:46.410 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:46.409 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:46.406 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:46.403 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:46.381 READ NATIVE MAX ADDRESS EXT Error 712 [11] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 01 c0 46 78 e1 00 00:01:42.630 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:42.629 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:42.626 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:42.623 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:42.601 READ NATIVE MAX ADDRESS EXT Error 711 [10] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 01 c0 46 78 e1 00 00:01:38.871 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:38.870 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:38.867 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:38.864 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:38.864 READ NATIVE MAX ADDRESS EXT Error 710 [9] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 01 c0 46 78 e1 00 00:01:35.081 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:35.080 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:35.077 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:35.074 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:35.074 READ NATIVE MAX ADDRESS EXT Error 709 [8] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 01 c0 46 78 e1 00 00:01:31.269 READ DMA ca 00 00 00 08 00 00 01 84 58 08 e1 00 00:01:31.268 WRITE DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:31.268 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:31.265 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:31.262 SET FEATURES [Set transfer mode] Error 708 [7] occurred at disk power-on lifetime: 54 hours (2 days + 6 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 40 -- 51 00 00 00 00 01 c0 46 78 00 00 Error: UNC at LBA = 0x01c04678 = 29378168 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- c8 00 00 00 08 00 00 01 c0 46 78 e1 00 00:01:27.529 READ DMA 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:27.528 READ NATIVE MAX ADDRESS EXT ec 00 00 00 00 00 00 00 00 00 00 a0 00 00:01:27.509 IDENTIFY DEVICE ef 00 03 00 46 00 00 00 00 00 00 a0 00 00:01:27.471 SET FEATURES [Set transfer mode] 27 00 00 00 00 00 00 00 00 00 00 e0 00 00:01:27.471 READ NATIVE MAX ADDRESS EXT SMART Extended Self-test Log Version: 1 (1 sectors) No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 522 (0x020a) SCT Support Level: 1 Device State: Active (0) Current Temperature: 28 Celsius Power Cycle Min/Max Temperature: 20/28 Celsius Lifetime Min/Max Temperature: 19/45 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 59 minutes Min/Max recommended Temperature: 14/55 Celsius Min/Max Temperature Limit: 10/60 Celsius Temperature History Size (Index): 128 (41) Index Estimated Time Temperature Celsius 42 2012-09-08 14:41 23 **** 43 2012-09-08 15:40 ? - 44 2012-09-08 16:39 24 ***** 45 2012-09-08 17:38 ? - 46 2012-09-08 18:37 21 ** 47 2012-09-08 19:36 ? - 48 2012-09-08 20:35 22 *** 49 2012-09-08 21:34 33 ************** 50 2012-09-08 22:33 34 *************** 51 2012-09-08 23:32 ? - 52 2012-09-09 00:31 21 ** 53 2012-09-09 01:30 ? - 54 2012-09-09 02:29 22 *** 55 2012-09-09 03:28 ? - 56 2012-09-09 04:27 22 *** 57 2012-09-09 05:26 ? - 58 2012-09-09 06:25 22 *** 59 2012-09-09 07:24 ? - 60 2012-09-09 08:23 23 **** 61 2012-09-09 09:22 ? - 62 2012-09-09 10:21 22 *** 63 2012-09-09 11:20 ? - 64 2012-09-09 12:19 22 *** 65 2012-09-09 13:18 ? - 66 2012-09-09 14:17 31 ************ 67 2012-09-09 15:16 ? - 68 2012-09-09 16:15 23 **** 69 2012-09-09 17:14 ? - 70 2012-09-09 18:13 24 ***** 71 2012-09-09 19:12 35 **************** 72 2012-09-09 20:11 ? - 73 2012-09-09 21:10 23 **** 74 2012-09-09 22:09 32 ************* 75 2012-09-09 23:08 ? - 76 2012-09-10 00:07 23 **** 77 2012-09-10 01:06 35 **************** 78 2012-09-10 02:05 ? - 79 2012-09-10 03:04 24 ***** 80 2012-09-10 04:03 35 **************** 81 2012-09-10 05:02 ? - 82 2012-09-10 06:01 23 **** 83 2012-09-10 07:00 34 *************** 84 2012-09-10 07:59 ? - 85 2012-09-10 08:58 24 ***** 86 2012-09-10 09:57 35 **************** 87 2012-09-10 10:56 35 **************** 88 2012-09-10 11:55 35 **************** 89 2012-09-10 12:54 ? - 90 2012-09-10 13:53 23 **** 91 2012-09-10 14:52 ? - 92 2012-09-10 15:51 23 **** 93 2012-09-10 16:50 34 *************** 94 2012-09-10 17:49 35 **************** 95 2012-09-10 18:48 ? - 96 2012-09-10 19:47 22 *** 97 2012-09-10 20:46 ? - 98 2012-09-10 21:45 23 **** 99 2012-09-10 22:44 ? - 100 2012-09-10 23:43 22 *** 101 2012-09-11 00:42 ? - 102 2012-09-11 01:41 22 *** 103 2012-09-11 02:40 ? - 104 2012-09-11 03:39 23 **** 105 2012-09-11 04:38 ? - 106 2012-09-11 05:37 24 ***** 107 2012-09-11 06:36 ? - 108 2012-09-11 07:35 23 **** 109 2012-09-11 08:34 ? - 110 2012-09-11 09:33 23 **** 111 2012-09-11 10:32 ? - 112 2012-09-11 11:31 23 **** 113 2012-09-11 12:30 ? - 114 2012-09-11 13:29 22 *** 115 2012-09-11 14:28 ? - 116 2012-09-11 15:27 21 ** 117 2012-09-11 16:26 32 ************* 118 2012-09-11 17:25 32 ************* 119 2012-09-11 18:24 ? - 120 2012-09-11 19:23 19 - 121 2012-09-11 20:22 ? - 122 2012-09-11 21:21 23 **** 123 2012-09-11 22:20 31 ************ 124 2012-09-11 23:19 ? - 125 2012-09-12 00:18 21 ** 126 2012-09-12 01:17 ? - 127 2012-09-12 02:16 23 **** 0 2012-09-12 03:15 ? - 1 2012-09-12 04:14 26 ******* 2 2012-09-12 05:13 ? - 3 2012-09-12 06:12 26 ******* 4 2012-09-12 07:11 ? - 5 2012-09-12 08:10 26 ******* 6 2012-09-12 09:09 ? - 7 2012-09-12 10:08 27 ******** 8 2012-09-12 11:07 ? - 9 2012-09-12 12:06 21 ** 10 2012-09-12 13:05 ? - 11 2012-09-12 14:04 21 ** 12 2012-09-12 15:03 32 ************* 13 2012-09-12 16:02 ? - 14 2012-09-12 17:01 21 ** 15 2012-09-12 18:00 33 ************** 16 2012-09-12 18:59 ? - 17 2012-09-12 19:58 21 ** 18 2012-09-12 20:57 32 ************* 19 2012-09-12 21:56 32 ************* 20 2012-09-12 22:55 ? - 21 2012-09-12 23:54 20 * 22 2012-09-13 00:53 ? - 23 2012-09-13 01:52 21 ** 24 2012-09-13 02:51 ? - 25 2012-09-13 03:50 21 ** 26 2012-09-13 04:49 33 ************** 27 2012-09-13 05:48 33 ************** 28 2012-09-13 06:47 ? - 29 2012-09-13 07:46 21 ** 30 2012-09-13 08:45 33 ************** 31 2012-09-13 09:44 33 ************** 32 2012-09-13 10:43 ? - 33 2012-09-13 11:42 21 ** 34 2012-09-13 12:41 33 ************** 35 2012-09-13 13:40 33 ************** 36 2012-09-13 14:39 32 ************* 37 2012-09-13 15:38 33 ************** 38 2012-09-13 16:37 32 ************* 39 2012-09-13 17:36 33 ************** 40 2012-09-13 18:35 ? - 41 2012-09-13 19:34 20 * SCT Error Recovery Control: Read: Disabled Write: Disabled SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x000a 2 2 Device-to-host register FISes sent due to a COMRESET 0x0001 2 0 Command failed due to ICRC error 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS