smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen Home page is http://smartmontools.sourceforge.net/ === START OF INFORMATION SECTION === Device Model: ST9320423AS Serial Number: 5VJ1WJFW Firmware Version: 0003HPM1 User Capacity: 320 072 933 376 bytes Device is: Not in smartctl database [for details use: -P showall] ATA Version is: 8 ATA Standard is: ATA-8-ACS revision 4 Local Time is: Sat Jun 4 13:35:34 2011 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x00) Offline data collection activity was never started. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x53) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. No Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 84) minutes. SCT capabilities: (0x103f) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 098 087 006 Pre-fail Always - 117712259 3 Spin_Up_Time 0x0002 097 097 000 Old_age Always - 0 4 Start_Stop_Count 0x0033 099 099 000 Pre-fail Always - 1095 5 Reallocated_Sector_Ct 0x0033 099 099 036 Pre-fail Always - 22 7 Seek_Error_Rate 0x000f 065 060 030 Pre-fail Always - 47285707328 9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 6489 10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0 12 Power_Cycle_Count 0x0033 099 037 020 Pre-fail Always - 1095 183 Unknown_Attribute 0x0032 100 253 000 Old_age Always - 0 184 Unknown_Attribute 0x0033 100 100 097 Pre-fail Always - 0 187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 317 188 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0 190 Airflow_Temperature_Cel 0x0022 057 052 045 Old_age Always - 43 (Lifetime Min/Max 29/47) 191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 2 193 Load_Cycle_Count 0x0032 012 012 000 Old_age Always - 177374 194 Temperature_Celsius 0x0022 043 048 000 Old_age Always - 43 (Lifetime Min/Max 0/62260) 195 Hardware_ECC_Recovered 0x001a 062 049 000 Old_age Always - 117712259 196 Reallocated_Event_Count 0x0033 099 099 036 Pre-fail Always - 22 197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 2 198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0 254 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 0 SMART Error Log Version: 1 ATA Error Count: 262 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 262 occurred at disk power-on lifetime: 6489 hours (270 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 58 8c 71 01 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 57 8c 71 41 00 02:35:57.708 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 02:35:57.708 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 00 02:35:57.706 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 02:35:57.706 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 00 02:35:57.705 SET FEATURES [Reserved for Serial ATA] Error 261 occurred at disk power-on lifetime: 6489 hours (270 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 58 8c 71 01 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 57 8c 71 41 00 02:35:55.004 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 02:35:55.003 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 00 02:35:55.002 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 02:35:54.974 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 00 02:35:54.973 SET FEATURES [Reserved for Serial ATA] Error 260 occurred at disk power-on lifetime: 6489 hours (270 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 58 8c 71 01 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 57 8c 71 41 00 02:35:52.175 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 02:35:52.175 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 00 02:35:52.070 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 02:35:52.070 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 00 02:35:52.069 SET FEATURES [Reserved for Serial ATA] Error 259 occurred at disk power-on lifetime: 6489 hours (270 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 58 8c 71 01 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 57 8c 71 41 00 02:35:49.379 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 02:35:49.378 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 00 02:35:49.377 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 02:35:49.376 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 00 02:35:49.376 SET FEATURES [Reserved for Serial ATA] Error 258 occurred at disk power-on lifetime: 6489 hours (270 days + 9 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 40 51 00 58 8c 71 01 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 00 08 57 8c 71 41 00 02:35:46.649 READ FPDMA QUEUED ef 10 02 00 00 00 a0 00 02:35:46.649 SET FEATURES [Reserved for Serial ATA] ec 00 00 00 00 00 a0 00 02:35:46.647 IDENTIFY DEVICE ef 03 45 00 00 00 a0 00 02:35:46.647 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 00 02:35:46.647 SET FEATURES [Reserved for Serial ATA] SMART Self-test log structure revision number 1 No self-tests have been logged. [To run self-tests, use: smartctl -t] SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.