smartctl 5.42 2011-10-20 r3458 [x86_64-linux-2.6.18-348.el5] (local build) Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net === START OF INFORMATION SECTION === Model Family: Western Digital RE4 Serial ATA Device Model: WDC WD1003FBYX-01Y7B1 Serial Number: WD-WCAW34755896 LU WWN Device Id: 5 0014ee 25d17716c Firmware Version: 01.01V02 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: 8 ATA Standard is: Exact ATA specification draft version not indicated Local Time is: Mon Feb 4 18:35:48 2013 CET SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x80) Offline data collection activity was never started. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (16500) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 162) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x303f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE 1 Raw_Read_Error_Rate POSR-K 200 200 051 - 0 3 Spin_Up_Time POS--K 185 185 021 - 3716 4 Start_Stop_Count -O--CK 100 100 000 - 13 5 Reallocated_Sector_Ct PO--CK 200 200 140 - 0 7 Seek_Error_Rate -OSR-K 200 200 000 - 0 9 Power_On_Hours -O--CK 100 100 000 - 604 10 Spin_Retry_Count -O--CK 100 253 000 - 0 11 Calibration_Retry_Count -O--CK 100 253 000 - 0 12 Power_Cycle_Count -O--CK 100 100 000 - 12 192 Power-Off_Retract_Count -O--CK 200 200 000 - 8 193 Load_Cycle_Count -O--CK 200 200 000 - 4 194 Temperature_Celsius -O---K 111 106 000 - 36 196 Reallocated_Event_Count -O--CK 200 200 000 - 0 197 Current_Pending_Sector -O--CK 200 200 000 - 0 198 Offline_Uncorrectable ----CK 100 253 000 - 0 199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0 200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0 ||||||_ K auto-keep |||||__ C event count ||||___ R error rate |||____ S speed/performance ||_____ O updated online |______ P prefailure warning General Purpose Log Directory Version 1 SMART Log Directory Version 1 [multi-sector log support] GP/S Log at address 0x00 has 1 sectors [Log Directory] SMART Log at address 0x01 has 1 sectors [Summary SMART error log] SMART Log at address 0x02 has 5 sectors [Comprehensive SMART error log] GP Log at address 0x03 has 6 sectors [Ext. Comprehensive SMART error log] SMART Log at address 0x06 has 1 sectors [SMART self-test log] GP Log at address 0x07 has 1 sectors [Extended self-test log] GP Log at address 0x08 has 2 sectors [Power Conditions log] SMART Log at address 0x09 has 1 sectors [Selective self-test log] GP Log at address 0x10 has 1 sectors [NCQ Command Error log] GP Log at address 0x11 has 1 sectors [SATA Phy Event Counters] GP/S Log at address 0x80 has 16 sectors [Host vendor specific log] GP/S Log at address 0x81 has 16 sectors [Host vendor specific log] GP/S Log at address 0x82 has 16 sectors [Host vendor specific log] GP/S Log at address 0x83 has 16 sectors [Host vendor specific log] GP/S Log at address 0x84 has 16 sectors [Host vendor specific log] GP/S Log at address 0x85 has 16 sectors [Host vendor specific log] GP/S Log at address 0x86 has 16 sectors [Host vendor specific log] GP/S Log at address 0x87 has 16 sectors [Host vendor specific log] GP/S Log at address 0x88 has 16 sectors [Host vendor specific log] GP/S Log at address 0x89 has 16 sectors [Host vendor specific log] GP/S Log at address 0x8a has 16 sectors [Host vendor specific log] GP/S Log at address 0x8b has 16 sectors [Host vendor specific log] GP/S Log at address 0x8c has 16 sectors [Host vendor specific log] GP/S Log at address 0x8d has 16 sectors [Host vendor specific log] GP/S Log at address 0x8e has 16 sectors [Host vendor specific log] GP/S Log at address 0x8f has 16 sectors [Host vendor specific log] GP/S Log at address 0x90 has 16 sectors [Host vendor specific log] GP/S Log at address 0x91 has 16 sectors [Host vendor specific log] GP/S Log at address 0x92 has 16 sectors [Host vendor specific log] GP/S Log at address 0x93 has 16 sectors [Host vendor specific log] GP/S Log at address 0x94 has 16 sectors [Host vendor specific log] GP/S Log at address 0x95 has 16 sectors [Host vendor specific log] GP/S Log at address 0x96 has 16 sectors [Host vendor specific log] GP/S Log at address 0x97 has 16 sectors [Host vendor specific log] GP/S Log at address 0x98 has 16 sectors [Host vendor specific log] GP/S Log at address 0x99 has 16 sectors [Host vendor specific log] GP/S Log at address 0x9a has 16 sectors [Host vendor specific log] GP/S Log at address 0x9b has 16 sectors [Host vendor specific log] GP/S Log at address 0x9c has 16 sectors [Host vendor specific log] GP/S Log at address 0x9d has 16 sectors [Host vendor specific log] GP/S Log at address 0x9e has 16 sectors [Host vendor specific log] GP/S Log at address 0x9f has 16 sectors [Host vendor specific log] GP/S Log at address 0xa0 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa1 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa2 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa3 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa4 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa5 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa6 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa7 has 16 sectors [Device vendor specific log] GP/S Log at address 0xa8 has 1 sectors [Device vendor specific log] GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log] GP/S Log at address 0xaa has 1 sectors [Device vendor specific log] GP/S Log at address 0xab has 1 sectors [Device vendor specific log] GP/S Log at address 0xac has 1 sectors [Device vendor specific log] GP/S Log at address 0xad has 1 sectors [Device vendor specific log] GP/S Log at address 0xae has 1 sectors [Device vendor specific log] GP/S Log at address 0xaf has 1 sectors [Device vendor specific log] GP/S Log at address 0xb0 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb1 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb2 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb3 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb4 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb5 has 1 sectors [Device vendor specific log] GP Log at address 0xb6 has 1 sectors [Device vendor specific log] GP/S Log at address 0xb7 has 1 sectors [Device vendor specific log] GP/S Log at address 0xbd has 1 sectors [Device vendor specific log] GP/S Log at address 0xc0 has 1 sectors [Device vendor specific log] GP Log at address 0xc1 has 24 sectors [Device vendor specific log] GP/S Log at address 0xe0 has 1 sectors [SCT Command/Status] GP/S Log at address 0xe1 has 1 sectors [SCT Data Transfer] SMART Extended Comprehensive Error Log Version: 1 (6 sectors) Device Error Count: 2 CR = Command Register FEATR = Features Register COUNT = Count (was: Sector Count) Register LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8 LH = LBA High (was: Cylinder High) Register ] LBA LM = LBA Mid (was: Cylinder Low) Register ] Register LL = LBA Low (was: Sector Number) Register ] DV = Device (was: Device/Head) Register DC = Device Control Register ER = Error register ST = Status register Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 2 [1] occurred at disk power-on lifetime: 576 hours (24 days + 0 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 0a 96 09 2f 40 00 Error: IDNF at LBA = 0x0a96092f = 177604911 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 00 00 00 0a 96 09 2f 40 08 22d+07:11:47.415 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 0a 96 09 37 40 08 22d+07:11:47.393 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 22d+07:11:47.393 FLUSH CACHE EXT 61 00 08 00 00 00 00 74 70 58 f8 40 08 22d+07:11:47.373 WRITE FPDMA QUEUED ea 00 00 00 00 00 00 00 00 00 00 e0 08 22d+07:11:47.343 FLUSH CACHE EXT Error 1 [0] occurred at disk power-on lifetime: 217 hours (9 days + 1 hours) When the command that caused the error occurred, the device was doing SMART Offline or Self-test. After command completion occurred, registers were: ER -- ST COUNT LBA_48 LH LM LL DV DC -- -- -- == -- == == == -- -- -- -- -- 10 -- 51 00 00 00 00 00 00 f7 df 40 00 Error: IDNF at LBA = 0x0000f7df = 63455 Commands leading to the command that caused the error were: CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name -- == -- == -- == == == -- -- -- -- -- --------------- -------------------- 61 00 08 00 00 00 00 00 00 f7 df 40 08 7d+06:56:14.709 WRITE FPDMA QUEUED 61 00 18 00 00 00 00 00 00 f7 c7 40 08 7d+06:56:14.697 WRITE FPDMA QUEUED 61 00 08 00 10 00 00 01 aa 5c 57 40 08 7d+06:56:14.677 WRITE FPDMA QUEUED 61 00 08 00 08 00 00 01 aa 55 47 40 08 7d+06:56:14.676 WRITE FPDMA QUEUED 61 00 08 00 00 00 00 0a 96 09 27 40 08 7d+06:56:14.668 WRITE FPDMA QUEUED SMART Extended Self-test Log Version: 1 (1 sectors) Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 597 - # 2 Extended offline Completed without error 00% 577 - # 3 Short offline Completed without error 00% 550 - # 4 Short offline Completed without error 00% 526 - # 5 Short offline Completed without error 00% 502 - # 6 Short offline Completed without error 00% 478 - # 7 Short offline Completed without error 00% 454 - # 8 Short offline Completed without error 00% 430 - # 9 Extended offline Completed without error 00% 409 - #10 Short offline Completed without error 00% 382 - #11 Short offline Completed without error 00% 358 - #12 Short offline Completed without error 00% 334 - #13 Short offline Completed without error 00% 311 - #14 Short offline Completed without error 00% 287 - #15 Short offline Completed without error 00% 263 - #16 Extended offline Completed without error 00% 242 - #17 Extended offline Completed without error 00% 218 - #18 Short offline Completed without error 00% 191 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. SCT Status Version: 3 SCT Version (vendor specific): 258 (0x0102) SCT Support Level: 1 Device State: Active (0) Current Temperature: 36 Celsius Power Cycle Min/Max Temperature: 30/40 Celsius Lifetime Min/Max Temperature: 30/41 Celsius Under/Over Temperature Limit Count: 0/0 SCT Temperature History Version: 2 Temperature Sampling Period: 1 minute Temperature Logging Interval: 1 minute Min/Max recommended Temperature: 0/60 Celsius Min/Max Temperature Limit: -41/85 Celsius Temperature History Size (Index): 478 (70) Index Estimated Time Temperature Celsius 71 2013-02-04 10:38 37 ****************** ... ..( 4 skipped). .. ****************** 76 2013-02-04 10:43 37 ****************** 77 2013-02-04 10:44 36 ***************** 78 2013-02-04 10:45 37 ****************** ... ..( 13 skipped). .. ****************** 92 2013-02-04 10:59 37 ****************** 93 2013-02-04 11:00 36 ***************** 94 2013-02-04 11:01 37 ****************** ... ..( 11 skipped). .. ****************** 106 2013-02-04 11:13 37 ****************** 107 2013-02-04 11:14 36 ***************** 108 2013-02-04 11:15 37 ****************** ... ..( 9 skipped). .. ****************** 118 2013-02-04 11:25 37 ****************** 119 2013-02-04 11:26 36 ***************** 120 2013-02-04 11:27 37 ****************** 121 2013-02-04 11:28 36 ***************** 122 2013-02-04 11:29 37 ****************** 123 2013-02-04 11:30 36 ***************** 124 2013-02-04 11:31 37 ****************** ... ..(180 skipped). .. ****************** 305 2013-02-04 14:32 37 ****************** 306 2013-02-04 14:33 36 ***************** ... ..( 9 skipped). .. ***************** 316 2013-02-04 14:43 36 ***************** 317 2013-02-04 14:44 37 ****************** 318 2013-02-04 14:45 36 ***************** ... ..(153 skipped). .. ***************** 472 2013-02-04 17:19 36 ***************** 473 2013-02-04 17:20 37 ****************** 474 2013-02-04 17:21 36 ***************** 475 2013-02-04 17:22 37 ****************** ... ..( 19 skipped). .. ****************** 17 2013-02-04 17:42 37 ****************** 18 2013-02-04 17:43 36 ***************** 19 2013-02-04 17:44 36 ***************** 20 2013-02-04 17:45 37 ****************** 21 2013-02-04 17:46 36 ***************** 22 2013-02-04 17:47 36 ***************** 23 2013-02-04 17:48 37 ****************** 24 2013-02-04 17:49 37 ****************** 25 2013-02-04 17:50 36 ***************** 26 2013-02-04 17:51 36 ***************** 27 2013-02-04 17:52 36 ***************** 28 2013-02-04 17:53 37 ****************** 29 2013-02-04 17:54 36 ***************** ... ..( 13 skipped). .. ***************** 43 2013-02-04 18:08 36 ***************** 44 2013-02-04 18:09 37 ****************** 45 2013-02-04 18:10 36 ***************** ... ..( 3 skipped). .. ***************** 49 2013-02-04 18:14 36 ***************** 50 2013-02-04 18:15 37 ****************** 51 2013-02-04 18:16 36 ***************** ... ..( 18 skipped). .. ***************** 70 2013-02-04 18:35 36 ***************** SCT Error Recovery Control: Read: 70 (7.0 seconds) Write: 70 (7.0 seconds) SATA Phy Event Counters (GP Log 0x11) ID Size Value Description 0x0001 2 0 Command failed due to ICRC error 0x0002 2 0 R_ERR response for data FIS 0x0003 2 0 R_ERR response for device-to-host data FIS 0x0004 2 0 R_ERR response for host-to-device data FIS 0x0005 2 0 R_ERR response for non-data FIS 0x0006 2 0 R_ERR response for device-to-host non-data FIS 0x0007 2 0 R_ERR response for host-to-device non-data FIS 0x0008 2 0 Device-to-host non-data FIS retries 0x0009 2 12 Transition from drive PhyRdy to drive PhyNRdy 0x000a 2 6 Device-to-host register FISes sent due to a COMRESET 0x000b 2 0 CRC errors within host-to-device FIS 0x000f 2 0 R_ERR response for host-to-device data FIS, CRC 0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC 0x8000 4 2026212 Vendor specific