Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
PCI: Found IRQ 11 for device 00:03.0
PCI: Sharing IRQ 11 with 00:03.1
PCI: Sharing IRQ 11 with 00:07.2
PCI: Found IRQ 11 for device 00:03.1
PCI: Sharing IRQ 11 with 00:03.0
PCI: Sharing IRQ 11 with 00:07.2
cs: cb_alloc(bus 2): vendor 0x115d, device 0x0003
eth0: Xircom cardbus revision 3 at irq 11
PCI: Enabling device 02:00.1 (0000 -> 0003)
ttyS04 at port 0x4080 (irq = 11) is a 16550A
Xircom cardbus adaptor found, registering as eth0, using irq 11
xircom_cb: enabling promiscuous mode
xircom_cb: capabilities changed from 0x1e1 to 0xa1
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x280-0x287 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
spurious 8259A interrupt: IRQ7.
#cardctl ident:
Socket 0:
product info: "Xircom", "CreditCard Ethernet 10/100 + Modem 56", "CEM56", "1.00"
manfid: 0x0105, 0x110a
function: 2 (serial)
#cardctl config:
Socket 0:
Vcc 5.0V Vpp1 0.0V Vpp2 0.0V
interface type is "memory and I/O"
irq 3 [shared] [level]
speaker output is enabled
function 0:
config base 0xff80
option 0x67 status 0x08 pin 0x00
io 0x0300-0x030f [16bit]
io 0x02e8-0x02ef [8bit]
Do kernelu zakonfigurovat Xircom CardBus
pouzit balicek pcmcia-cs - bez tohohle balicku proste nejede.
Linux Mandrake 8.2 s kernelem 2.4.18mdk s balickem pcmcia_cs-3.1.31 si s kartou hrave poradil.
moduly: xirc2ps_cs, serial_cs, pcmcia_core
Seznam AT prikazu:
http://support.ap.dell.com/docs/NETWORK/5606d/commset.htm
Ve woknech mi jede na 100 Mbit az 6 MB/s ale v linuchu i kdyz ji identifikuje spravne a link 100 Mbit sviti, tak jede MAX 400 KB/s!!! Ach jo...nekdy ten linux nejlepsi neni.
Zkouseno v kernelu 2.4.18
Doplneno od verze kernelu 2.4.19-pre5 funguje i pod linuxem na 6.5 Mbit/s, takze jestli mate tuhle kartu, tak jedine s kernely 2.4.19 a vyse
V dobre vire jsem provedl upgrade firmware modemu z verze 2.70 na verzi 2.90. Modem ale je po upgrade firmware velmi nespolehlivy. Intel o reseni problemu moc zajem nema, je to stary produkt. Ale pomohlo prepnuti modemu do V.34 rezimu, ktere se provadi pomoci ATS38=0.V algoritmu V.90 firmwaru 2.90 je nejaka fatalni chyba... Mozna ze modem umi jen 56Kflex, ne V.90.
