Nikon Coolpix 2000 pod 2.6

Ahoj, je tu nekdo, komu chodi fotak Nikon Coolpix 2000 pod jadrem 2.6? Zkousel jsem uz 2.6.3,7,8 a porad nic. Vim, na nekterych strankach jsem se docetl, ze je potreba aplikovat patch (mam ale pocit, ze u 2.6.8 uz neni potreba). Jenze ani pak mi nefunguje. Podezrivam z problemu nejaky modul k usb, zrejme ohci-hcd, ktery po zkusmem pripojeni fotaku (kdy fotak nejde primountovat) a naslednem tvrdem odpojeni zustava viset na nejakem timeoutu a nejde s nim hnout.

dmesg:
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
ohci_hcd 0000:00:02.0: nVidia Corporation nForce USB Controller
ohci_hcd 0000:00:02.0: reset, control = 0x600
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: irq 5, pci mem df1e7000
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1
ohci_hcd 0000:00:02.0: supports USB remote wakeup
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: default language 0x0409
usb usb1: Product: nVidia Corporation nForce USB Controller
usb usb1: Manufacturer: Linux 2.6.7-gentoo-r11 ohci_hcd
usb usb1: SerialNumber: 0000:00:02.0
usb usb1: hotplug
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: hotplug
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 3 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: global over-current protection
hub 1-0:1.0: power on to power good time: 2ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: no over-current condition exists
ohci_hcd 0000:00:02.0: created debug files
ohci_hcd 0000:00:02.0: OHCI controller state
ohci_hcd 0000:00:02.0: OHCI 1.0, with legacy support registers
ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:02.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:02.0: hcca frame #002d
ohci_hcd 0000:00:02.0: roothub.a 01000203 POTPGT=1 NPS NDP=3
ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:02.0: roothub.status 00000000
ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:03.0: nVidia Corporation nForce USB Controller (#2)
ohci_hcd 0000:00:03.0: reset, control = 0x600
PCI: Setting latency timer of device 0000:00:03.0 to 64
ohci_hcd 0000:00:03.0: irq 11, pci mem df1e9000
ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:03.0: supports USB remote wakeup
usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: default language 0x0409
usb usb2: Product: nVidia Corporation nForce USB Controller (#2)
usb usb2: Manufacturer: Linux 2.6.7-gentoo-r11 ohci_hcd
usb usb2: SerialNumber: 0000:00:03.0
usb usb2: hotplug
usb usb2: adding 2-0:1.0 (config #1, interface 0)
usb 2-0:1.0: hotplug
hub 2-0:1.0: usb_probe_interface
hub 2-0:1.0: usb_probe_interface - got id
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
hub 2-0:1.0: standalone hub
hub 2-0:1.0: no power switching (usb 1.0)
hub 2-0:1.0: global over-current protection
hub 2-0:1.0: power on to power good time: 2ms
hub 2-0:1.0: local power source is good
hub 2-0:1.0: no over-current condition exists
ohci_hcd 0000:00:02.0: suspend root hub
ohci_hcd 0000:00:03.0: created debug files
ohci_hcd 0000:00:03.0: OHCI controller state
ohci_hcd 0000:00:03.0: OHCI 1.0, with legacy support registers
ohci_hcd 0000:00:03.0: control 0x683 RWE RWC HCFS=operational CBSR=3
ohci_hcd 0000:00:03.0: cmdstatus 0x00000 SOC=0
ohci_hcd 0000:00:03.0: intrstatus 0x00000004 SF
ohci_hcd 0000:00:03.0: intrenable 0x8000000a MIE RD WDH
ohci_hcd 0000:00:03.0: hcca frame #008c
ohci_hcd 0000:00:03.0: roothub.a 01000203 POTPGT=1 NPS NDP=3
ohci_hcd 0000:00:03.0: roothub.b 00000000 PPCM=0000 DR=0000
ohci_hcd 0000:00:03.0: roothub.status 00000000
ohci_hcd 0000:00:03.0: roothub.portstatus [0] 0x00000100 PPS
ohci_hcd 0000:00:03.0: roothub.portstatus [1] 0x00000100 PPS
ohci_hcd 0000:00:03.0: roothub.portstatus [2] 0x00000100 PPS
ohci_hcd 0000:00:03.0: suspend root hub
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [3] = 0x00010101 CSC PPS CCS
hub 2-0:1.0: port 3, status 0101, change 0001, 12 Mb/s
hub 2-0:1.0: debounce: port 3: delay 100ms stable 4 status 0x101
ohci_hcd 0000:00:03.0: GetStatus roothub.portstatus [3] = 0x00100103 PRSC PPS PES CCS
usb 2-3: new full speed USB device using address 2
usb 2-3: control timeout on ep0out

Diky.

Dotaz: Nikon Coolpix 2000 pod 2.6

Odpovědi