Leadtek WinFast DTV Dongle

USB2.0, DVB-T, Infra port

usb 4-2: new high speed USB device using ehci_hcd and address 8
usb 4-2: configuration #1 chosen from 1 choice
dvb-usb: found a 'Leadtek - USB2.0 Winfast DTV dongle' in cold state, will try to load a firmware
dvb-usb: downloading firmware from file 'dvb-usb-dibusb-6.0.0.8.fw'
usbcore: registered new driver dvb_usb_dibusb_mc
usb 4-2: USB disconnect, address 8
dvb-usb: generic DVB-USB module successfully deinitialized and disconnected.
usb 4-2: new high speed USB device using ehci_hcd and address 9
usb 4-2: configuration #1 chosen from 1 choice
dvb-usb: found a 'Leadtek - USB2.0 Winfast DTV dongle' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Leadtek - USB2.0 Winfast DTV dongle).
DVB: registering frontend 0 (DiBcom 3000MC/P)...
MT2060: successfully identified (IF1 = 1220)
input: IR-receiver inside an USB DVB receiver as /class/input/input19
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: Leadtek - USB2.0 Winfast DTV dongle successfully initialized and connected.

Jiná verze se stejnym designem, ale jinymi strevy.

usb 1-2: new high speed USB device using ehci_hcd and address 5
usb 1-2: configuration #1 chosen from 1 choice
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in cold state, will try to load a firmware
firmware: requesting dvb-usb-dib0700-1.10.fw
dvb-usb: downloading firmware from file 'dvb-usb-dib0700-1.10.fw'
dib0700: firmware started successfully.
dvb-usb: found a 'Leadtek Winfast DTV Dongle (STK7700P based)' in warm state.
dvb-usb: will pass the complete MPEG2 transport stream to the software demuxer.
DVB: registering new adapter (Leadtek Winfast DTV Dongle (STK7700P based))
DVB: registering frontend 0 (DiBcom 7000MA/MB/PA/PB/MC)...
MT2060: successfully identified (IF1 = 1220)
input: IR-receiver inside an USB DVB receiver as /class/input/input5
dvb-usb: schedule remote query interval to 150 msecs.
dvb-usb: Leadtek Winfast DTV Dongle (STK7700P based) successfully initialized and connected.

Ovladač je součástí kernelu. Popis zprovoznění třeba tuto

RC je z větší části funkční, jen některá tlačítka obšas zlobí. Aby byla tlačítka použitelná v Xkách, je třeba použít buď lirc nebo klávesy namapovat nějak takto např:

xmodmap -e 'keycode 10=XF86Launch1'
xmodmap -e 'keycode 11=XF86Launch2'
xmodmap -e 'keycode 12=XF86Launch3'
xmodmap -e 'keycode 13=XF86Launch4'
xmodmap -e 'keycode 14=XF86Launch5'
xmodmap -e 'keycode 15=XF86Launch6'
xmodmap -e 'keycode 16=XF86Launch7'
xmodmap -e 'keycode 17=XF86Launch8'
xmodmap -e 'keycode 18=XF86Launch9'
xmodmap -e 'keycode 19=XF86Launch0'
xmodmap -e 'keycode 160=XF86AudioMute'
xmodmap -e 'keycode 177=XF86AudioRecord'
xmodmap -e 'keycode 16=XF86AudioPrev'
xmodmap -e 'keycode 17=XF86AudioNext'

Pocitove preladuje rychleji z multiplexu na multiplex nez moje druha dongle Freecom DVB-T