HP Vectra XU 6/2000

Case ATX miditower, Dual Pentium Pro 200 MHz, IDE/SCSI on board, SB 16 on board, 128 MB (8*16MB) EDO-DIMM 5V, ECC. Pridana graficka karta Matrox Millenium, SCSI disk 2 GB, IDE disk 4,3 GB a IDE 36x AOpen CD-ROM, 100base/TX ethernet karta 3c905. Klabosnice+mys - PS/2

Linux version 2.4.2-2smp (root@porky.devel.redhat.com) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-79)) #1 SMP Sun Apr 8 20:21:34 EDT 2001
...
Intel MultiProcessor Specification v1.1
    Virtual Wire compatibility mode.
OEM ID: HP       Product ID: XX           APIC at: 0xFEE00000
Processor #1 Pentium(tm) Pro APIC version 17
    Floating point unit present.
    Machine Exception supported.
    64 bit compare & exchange supported.
    Internal APIC present.
    SEP present.
    MTRR  present.
    PGE  present.
    MCA  present.
    CMOV  present.
    Bootup CPU
Processor #0 Pentium(tm) Pro APIC version 17
...
Bus #1 is ISA
Bus #0 is PCI
I/O APIC #16 Version 17 at 0xFEC00000.
...
Processors: 2
...
Kernel command line: auto BOOT_IMAGE=linux-2.4.2 ro root=302 BOOT_FILE=/boot/vmlinuz-2.4.2-2smp
Initializing CPU#0
Detected 199.748 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 398.13 BogoMIPS
Memory: 125656k/131072k available (1500k kernel code, 5028k reserved, 103k data, 252k init, 0k highmem)
Boot done.
...
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 16.
testing the IO APIC.......................
...
calibrating APIC timer ...
..... CPU clock speed is 199.7398 MHz.
..... host bus clock speed is 66.5796 MHz.
cpu: 0, clocks: 665796, slice: 221932
CPU0
...
PCI: PCI BIOS revision 2.00 entry at 0xfbf00, last bus=0
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: i440KX/GX host bridge 00:19.0: secondary bus 00
PCI: Device 00:a0 not found by BIOS
PCI: Device 00:c8 not found by BIOS
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Starting kswapd v1.8
vesafb: framebuffer at 0xa0800000, mapped to 0xc8800000, size 4096k
vesafb: mode is 800x600x8, linelength=1024, pages=2
vesafb: protected mode interface info at c000:7ba0
vesafb: scrolling: redraw
Console: switching to colour frame buffer device 100x37
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
block: queued sectors max/low 83264kB/27754kB, 256 slots per queue
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
CMD646: IDE controller on PCI bus 00 dev 08
CMD646: chipset revision 1
CMD646: not 100% native mode: will probe irqs later
CMD646: chipset revision 0x01, MultiWord DMA Limited, IRQ workaround enabled
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:pio, hdd:pio
hda: WDC AC24300L, ATA DISK drive
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hdd: CD-ROM 36X/AKU, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 8421840 sectors (4312 MB) w/256KiB Cache, CHS=557/240/63, (U)DMA
Partition check:
 hda: hda1 hda2 hda3 < hda5 >
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 361k freed
Serial driver version 5.02 (2000-08-09) with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10d
md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md.c: sizeof(mdp_super_t) = 4096
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 8192 bind 8192)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
(scsi0)  found at PCI 0/2/0
(scsi0) Narrow Channel, SCSI ID=7, 16/255 SCBs
(scsi0) Downloading sequencer code... 436 instructions downloaded
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.2.4/5.2.0
       
  Vendor: SEAGATE   Model: ST32151N          Rev: HP01
  Type:   Direct-Access                      ANSI SCSI revision: 02
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:0:0) Synchronous at 10.0 Mbyte/sec, offset 15.
SCSI device sda: 4194685 512-byte hdwr sectors (2148 MB)
 sda: sda1
VFS: Mounted root (ext2 filesystem) readonly.
change_root: old root has d_count=3
Freeing unused kernel memory: 252k freed
Adding Swap: 264560k swap-space (priority -1)
Soundblaster audio driver Copyright (C) by Hannu Savolainen 1993-1996
sb: No ISAPnP cards found, trying standard ones...
SB 4.13 detected OK (220)
Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...
SMSC Super-IO detection, now testing Ports 2F0, 370 ...
0x378: FIFO is 16 bytes
0x378: writeIntrThreshold is 8
0x378: readIntrThreshold is 8
0x378: PWord is 8 bits
0x378: Interrupts are ISA-Pulses
0x378: ECP port cfgA=0x10 cfgB=0x4b
0x378: ECP settings irq=7 dma=3
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,COMPAT,ECP]
parport0: irq 7 detected
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
parport0: cpp_daisy: aa5500ff(38)
parport0: assign_addrs: aa5500ff(38)
ip_conntrack (1024 buckets, 8192 max)
3c59x.c:LK1.1.13 27 Jan 2001  Donald Becker and others. http://www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
eth0: 3Com PCI 3c905 Boomerang 100baseTx at 0xf400,  00:60:08:aa:bd:f8, IRQ 11
  product code 4b4b rev 00.0 date 10-26-97
  8K word-wide RAM 3:5 Rx:Tx split, autoselect/MII interface.
  MII transceiver found at address 24, status 786d.
  Enabling bus-master transmits and whole-frame receives.
eth0: scatter/gather disabled. h/w checksums disabled
eth0: first available media type: MII
eth0: first available media type: MII
hdd: ATAPI 32X CD-ROM drive, 128kB Cache
Uniform CD-ROM driver Revision: 3.12
...

Vubec zadny problem, zkousel jsem RH 7.1CZ a Mandrake 8.2, nabootuje z CD, vse nainstaluje a vse jede.

Nejvice bezproblemova instalace Linuxu, jakou jsem kdy zazil...