IBM-DTLA-305040

IBM DeskStar 40GV family
80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, UDMA(44), 5400RPM

http://www.storage.ibm.com/hdd/desk/ds40gv.htm

hdparm -i /dev/hda:
 Model=IBM-DTLA-305040, FwRev=TW4OA60A, SerialNo=YJEYJ0Q2910
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=40
 BuffType=DualPortCache, BuffSize=380kB, MaxMultSect=16, MultSect=16
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=80418240
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes: pio0 pio1 pio2 pio3 pio4
 DMA modes: mdma0 mdma1 mdma2 udma0 udma1 udma2 *udma3 udma4 udma5
 AdvancedPM=yes: disabled (255) WriteCache=enabled
 Drive Supports : ATA/ATAPI-5 T13 1321D revision 1 : ATA-2 ATA-3 ATA-4 ATA-5

hdparm -I /dev/hda:
non-removable ATA device, with non-removable media
powers-up in standby; SET FEATURES subcmd spins-up.

        WARNING: ID response incomplete.
        WARNING: Following data may be incorrect.

        Model Number:           IBM-DTLA-305040
        Serial Number:                   YJEYJ0Q2910
        Firmware Revision:      TW4OA60A
Standards:
        Used: ATA/ATAPI-5 T13 1321D revision 1
        Supported: 2 3 4 5
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        bytes/track:    0               (obsolete)
        bytes/sector:   0               (obsolete)
        current sector capacity: 16514064
        LBA user addressable sectors = 80418240
Capabilities:
        LBA, IORDY(can be disabled)
        Buffer size: 380.0kB    ECC bytes: 40   Queue depth: 32
        Standby timer values: spec'd by standard, no device specific minimum
        r/w multiple sector transfer: Max = 16  Current = 16
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 *udma3 udma4 udma5
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    NOP cmd
           *    READ BUFFER cmd
           *    WRITE BUFFER cmd
           *    Host Protected Area feature set
                release interrupt
           *    look-ahead
           *    write cache
           *    Power Management feature set
                Security Mode feature set
                SMART feature set
                SET MAX security extension
                Address offset used (large drive)
                SET FEATURES subcommand required to spinup after power up
                Power-Up In Standby feature set
                Advanced Power Management feature set
           *    READ/WRITE DMA QUEUED
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
        not     supported: enhanced erase
        42min for SECURITY ERASE UNIT.
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by the jumper
Checksum: correct