ST360021A

/dev/hda:
 multcount    = 16 (on)
 IO_support   =  0 (default 16-bit)
 using_dma    =  1 (on)
 readahead    =  8 (on)
 geometry     = 7297/255/63, sectors = 117231408, start = 0

 Model=ST360021A, FwRev=3.10, SerialNo=3HR0GX3L
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=2048kB, MaxMultSect=16, MultSect=16
 CurCHS=4047/16/255, CurSects=16511760, LBA=yes, LBAsects=117231408
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4 
 DMA modes:  mdma0 mdma1 mdma2 
 UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5 
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: device does not report version:  1 2 3 4 5


ATA device, with non-removable media
        Model Number:       ST360021A                               
        Serial Number:      3HR0GX3L            
        Firmware Revision:  3.10    
Standards:
        Supported: 5 4 3 2 
        Likely used: 6
Configuration:
        Logical         max     current
        cylinders       16383   4047
        heads           16      16
        sectors/track   63      255
        --
        CHS current addressable sectors:   16511760
        LBA    user addressable sectors:  117231408
        device size with M = 1024*1024:       57241 MBytes
        device size with M = 1000*1000:       60022 MBytes (60 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        bytes avail on r/w long: 4      Queue depth: 1
        Standby timer values: spec'd by Standard
        R/W multiple sector transfer: Max = 16  Current = 16
        Recommended acoustic management value: 128, current value: 0
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5 
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4 
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    READ BUFFER cmd
           *    WRITE BUFFER cmd
           *    Host Protected Area feature set
           *    Look-ahead
           *    Write cache
           *    Power Management feature set
                Security Mode feature set
           *    SMART feature set
                Device Configuration Overlay feature set 
                Automatic Acoustic Management feature set 
                SET MAX security extension
           *    DOWNLOAD MICROCODE cmd
Security: 
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
        not     supported: enhanced erase
HW reset results:
        CBLID- above Vih
        Device num = 1
Checksum: correct



[root@burdazd.sh.cvut.cz]$ hdparm -ftT /dev/hda

/dev/hda:
 Timing buffer-cache reads:   128 MB in  0.49 seconds =261.22 MB/sec
 Timing buffered disk reads:  64 MB in  1.73 seconds = 36.99 MB/sec

hda: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=7297/255/63, UDMA(100)

zakompilovani podpory IDE do jadra

pomoci smartctl se dá zjistit hodně zajímavých údajů(teplota,doba provozu, počet chyb...)smartctl -a /dev/hda. je to tichý, levný a do domácího počítače dostatečně rychlý HDD.