ASUS P8Z77-M PRO

mATX
LGA 1155 (Ivy Bridge)
Chipset Intel Z77
4x DIMM DDR3 1600 (max. 32GB)
2xPCIe 3.0/2.0 x16
1x PCIe 2.0 x16
1x PCIe 2.0 x1
(bez PCI slotu)
HDMI max. 1920x1200@60
DVI-D max. 1920x1200@60
D-SUB max. 2048x1536@75
max. shared VRAM 1696MB
2x SATA 6Gb/s
4x SATA 3Gb/s
2x eSATA 6Gb/s
RJ-45
RealTek ALC892
S/PDIF
6x USB3
8x USB2
3x chassis FAN

$ lspci
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor DRAM Controller (rev 09)
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v2/3rd Gen Core processor PCI Express Root Port (rev 09)
00:14.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller (rev 04)
00:16.0 Communication controller: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 (rev 04)
00:1a.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 (rev 04)
00:1b.0 Audio device: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller (rev 04)
00:1c.0 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 1 (rev c4)
00:1c.4 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 5 (rev c4)
00:1c.5 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 6 (rev c4)
00:1c.6 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 7 (rev c4)
00:1c.7 PCI bridge: Intel Corporation 7 Series/C210 Series Chipset Family PCI Express Root Port 8 (rev c4)
00:1d.0 USB controller: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 (rev 04)
00:1f.0 ISA bridge: Intel Corporation Z77 Express Chipset LPC Controller (rev 04)
00:1f.2 SATA controller: Intel Corporation 7 Series/C210 Series Chipset Family 6-port SATA Controller [AHCI mode] (rev 04)
00:1f.3 SMBus: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller (rev 04)
04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 09)
05:00.0 USB controller: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller
06:00.0 SATA controller: ASMedia Technology Inc. ASM1062 Serial ATA Controller (rev 01)

$ lsusb
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 003 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 003 Device 003: ID 04b4:2050 Cypress Semiconductor Corp. hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub

$ sensors
acpitz-virtual-0
Adapter: Virtual device
temp1:        +27.8°C  (crit = +106.0°C)
temp2:        +29.8°C  (crit = +106.0°C)

coretemp-isa-0000
Adapter: ISA adapter
Physical id 0:  +39.0°C  (high = +85.0°C, crit = +105.0°C)
Core 0:         +36.0°C  (high = +85.0°C, crit = +105.0°C)
Core 1:         +30.0°C  (high = +85.0°C, crit = +105.0°C)
Core 2:         +32.0°C  (high = +85.0°C, crit = +105.0°C)
Core 3:         +34.0°C  (high = +85.0°C, crit = +105.0°C)

nct6779-isa-0290
Adapter: ISA adapter
in0:                    +0.84 V  (min =  +0.00 V, max =  +1.74 V)
in1:                    +1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in2:                    +3.39 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in3:                    +3.39 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in4:                    +1.02 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in5:                    +2.04 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in6:                    +0.28 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in7:                    +3.42 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in8:                    +3.36 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in9:                    +1.06 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in10:                   +0.22 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in11:                   +0.18 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in12:                   +0.18 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in13:                   +0.18 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
in14:                   +0.18 V  (min =  +0.00 V, max =  +0.00 V)  ALARM
fan1:                   333 RPM  (min =    0 RPM)
fan2:                   369 RPM  (min =    0 RPM)
fan3:                   319 RPM  (min =    0 RPM)
fan4:                     0 RPM  (min =    0 RPM)
fan5:                     0 RPM  (min =    0 RPM)
SYSTIN:                 +30.0°C  (high =  +0.0°C, hyst =  +0.0°C)  ALARM  sensor = thermistor
CPUTIN:                 +36.5°C  (high = +80.0°C, hyst = +75.0°C)  sensor = thermistor
AUXTIN0:                +96.0°C    sensor = thermistor
AUXTIN1:               +100.0°C    sensor = thermistor
AUXTIN2:               +100.0°C    sensor = thermistor
AUXTIN3:                 +3.0°C    sensor = thermal diode
PCH_CHIP_CPU_MAX_TEMP:   +0.0°C  
PCH_CHIP_TEMP:           +0.0°C  
PCH_CPU_TEMP:            +0.0°C  
PCH_MCH_TEMP:            +0.0°C  
cpu0_vid:              +0.000 V
intrusion0:            ALARM
intrusion1:            ALARM

$ cat /etc/fancontrol
# Temperature control for Core i5-3570K (Ivy Bridge) + board ASUS P8Z77-M PRO + case CoolerMaster Silencio 550 + fans: Arctic Cooling Freezer 13 + 2x Arctic Cooling Arctic F12 PWM
# tested with fancontrol 3.3.1 (Ubuntu 12.10)

# requires:	add-apt-repositories ppa:foresto/extradrivers
# 		modprobe nct6775
#		change priority of RC script /etc/rc2.d/S20fancontrol to S99
#		modify the RC script: add rmmod nct6775; modprobe nct6775 before start-stop-daemon line (rmmod fixes the device name; otherwise it would depend on random kernel module load order)
# re-apply fancontol on resume: add executable script /etc/pm/sleep.d/20_fancontrol that runs service fancontrol restart when $1 = resume or thaw (else fans will run at 100% RPM after resume)

# CPU socket temp:         /sys/devices/platform/coretemp.0/temp1_input
# CPU fan RPM:             /sys/devices/platform/nct6775.656/fan2_input
# Chassis exhaust fan RPM: /sys/devices/platform/nct6775.656/fan1_input
# Chassis intake fan RPM:  /sys/devices/platform/nct6775.656/fan3_input
# CPU fan PWM:             /sys/devices/platform/nct6775.656/fan2
# Chassis exhaust fan PWM: /sys/devices/platform/nct6775.656/fan1
# Chassis intake fan PWM:  /sys/devices/platform/nct6775.656/fan3

INTERVAL= 10
DEVPATH=  hwmon1=devices/platform/coretemp.0 hwmon3=devices/platform/nct6775.656
DEVNAME=  hwmon1=coretemp           hwmon3=nct6779

# Use temp measurement from physical CPU socket (is higher than CPUTIN, immediately follows load changes and respects all CPU core temps)
FCTEMPS=  hwmon3/device/pwm1=hwmon1/device/temp1_input hwmon3/device/pwm2=hwmon1/device/temp1_input hwmon3/device/pwm3=hwmon1/device/temp1_input
FCFANS=   hwmon3/device/pwm1=hwmon3/device/fan1_input  hwmon3/device/pwm2=hwmon3/device/fan2_input  hwmon3/device/pwm3=hwmon3/device/fan3_input

# Use PWM between 38 and 60 degrees (with quadratic RPM growth). Keep minimal RPM (around 300 thanks to aftermarket fans) until 38 degrees and keep maximum RPM above 60 degrees
MINTEMP=  hwmon3/device/pwm1=38  hwmon3/device/pwm2=38  hwmon3/device/pwm3=38
MAXTEMP=  hwmon3/device/pwm1=60  hwmon3/device/pwm2=60  hwmon3/device/pwm3=60
MINSTART= hwmon3/device/pwm1=60  hwmon3/device/pwm2=30  hwmon3/device/pwm3=60
MINSTOP=  hwmon3/device/pwm1=53  hwmon3/device/pwm2=26  hwmon3/device/pwm3=55
MINPWM=   hwmon3/device/pwm1=53  hwmon3/device/pwm2=26  hwmon3/device/pwm3=55
MAXPWM=   hwmon3/device/pwm1=255 hwmon3/device/pwm2=255 hwmon3/device/pwm3=255

# Possible alternative temp source: CPUTIN (IMO worse than coretemp)
# CPU temp: /sys/devices/platform/nct6775.656/temp2_input
# FCTEMPS=  hwmon3/device/pwm1=hwmon3/device/temp2_input hwmon3/device/pwm2=hwmon3/device/temp2_input hwmon3/device/pwm3=hwmon3/device/temp2_input

Podpora pro LM Sensors vyzaduje (bezproblemovou) instalaci ovladace nct6775.
Je pripravena na masivni pretaktovani, takze pri standardni konfiguraci malo topi.
Maximalni spokojenost.