Napalovanie

Ahoj,

Pouzivam Lenovo Thinkpad SL500, OS Ubuntu 9.10. A mam problem - akosi mi nefunguje napalovanie. Potreboval som totiz vypalit .iso obraz na CD a akosi nie a nie to dokoncit. Podobne je to aj pri DVD, skratka nikdy uspesne nedokonci ani vypalovanie v dummy mode. Skusal som Brasero, GnomeBaker, K3b (aj ked to je asi jedno, nie?), dokonca som skusil aj priamo Wodim, bezvysledne.

Prikladam vypis programu GnomeBaker (tie vypisy su takmer vsetky rovnake, asi nema zmysel davat aj dalsie):

wodim: No write mode specified.
wodim: Asuming -tao mode.
wodim: Future versions of wodim may have different drive dependent defaults.
wodim: Operation not permitted. Warning: Cannot raise RLIMIT_MEMLOCK limits.scsidev: '/dev/sr0'
devname: '/dev/sr0'
scsibus: -2 target: -2 lun: -2
Linux sg driver version: 3.5.27
Wodim version: 1.1.9
SCSI buffer size: 64512
Beginning DMA speed test. Set CDR_NODMATEST environment variable if device
communication breaks or freezes immediately after that.
TOC Type: 3 = CD-ROM XA mode 2
Driveropts: 'burnfree'
Device type : Removable CD-ROM
Version : 5
Response Format: 2
Capabilities :
Vendor_info : 'HL-DT-ST'
Identification : 'DVDRAM GSA-T50N '
Revision : 'RE06'
Device seems to be: Generic mmc2 DVD-R/DVD-RW.
Current: 0x0009 (CD-R)
Profile: 0x0012 (DVD-RAM)
Profile: 0x0011 (DVD-R sequential recording)
Profile: 0x0015 (DVD-R/DL sequential recording)
Profile: 0x0016 (DVD-R/DL layer jump recording)
Profile: 0x0014 (DVD-RW sequential recording)
Profile: 0x0013 (DVD-RW restricted overwrite)
Profile: 0x001A (DVD+RW)
Profile: 0x001B (DVD+R)
Profile: 0x002B (DVD+R/DL)
Profile: 0x0010 (DVD-ROM)
Profile: 0x0009 (CD-R) (current)
Profile: 0x000A (CD-RW)
Profile: 0x0008 (CD-ROM)
Profile: 0x0002 (Removable disk)
Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
Driver flags : MMC-3 SWABAUDIO BURNFREE
Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
Drive buf size : 1053696 = 1029 KB
Drive DMA Speed: 15658 kB/s 88x CD 11x DVD
FIFO size : 12582912 = 12288 KB
Speed set to 4234 KB/s
????????????? 4 seconds.????????????? 3 seconds.????????????? 2 seconds.????????????? 1 seconds.????????????? 0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Starting new track at sector: 0
Errno: 5 (Input/output error), write_g1 scsi sendcmd: no error
CDB: 2A 00 00 00 02 0F 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 2A 30 02 80 21 02 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x21 Qual 0x02 (invalid address for write) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.006s timeout 40s
wodim: The current problem looks like a buffer underrun.
wodim: It looks like 'driveropts=burnfree' does not work for this drive.
wodim: Please report.
wodim: Make sure that you are root, enable DMA and check your HW/OS set up.

write track data: error after 1079296 bytes
Writing time: 11.170s
Average write speed 231.5x.
Min drive buffer fill was 98%
Fixating...
WARNING: Some drives don't like fixation in dummy mode.
Fixating time: 28.695s
wodim: fifo had 209 puts and 18 gets.
wodim: fifo was 0 times empty and 6 times full, min fill was 96%.

Ma niekto nejake rady, nieco co by som mohol vyskusat? Alebo mam cakat na Lucid Lynx a dufat, ze tam to pojde?

Dotaz: Napalovanie

Odpovědi