USB support, 2.4.x

Nedari se mi zkompilovat 2.4kove jadro s podpporou USB mass storage devices. S distribucnim jadrem proste mount /dev/sdax chodi, zatimco mne ani nahodou. Prihazuju, co to hlasi pri startu a tez parametry, se kterymi to kompiluju. Prosim o radu, naslepo uz to zkousim nejaky cas a nic moc :(

usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
host/usb-uhci.c: $Revision: 1.275 $ time 21:00:38 May 14 2006
host/usb-uhci.c: High bandwidth mode enabled
host/usb-uhci.c: USB UHCI at I/O 0xe000, IRQ 5
host/usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-uhci.c: USB UHCI at I/O 0xe400, IRQ 5
host/usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
host/usb-uhci.c: v1.275:USB Universal Host Controller Interface driver

hub.c: new USB device 00:11.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x7b4/0x105) is not claimed by any active driver.
SCSI subsystem driver Revision: 1.00
usb.c: USB disconnect on device 00:11.2-1 address 2
hub.c: new USB device 00:11.2-1, assigned address 3
usb.c: USB device 3 (vend/prod 0x7b4/0x105) is not claimed by any active driver.

.config

#
# USB support
#
CONFIG_USB=y
# CONFIG_USB_DEBUG is not set
CONFIG_USB_DEVICEFS=y
# CONFIG_USB_BANDWIDTH is not set
# CONFIG_USB_EHCI_HCD is not set
CONFIG_USB_UHCI=y
# CONFIG_USB_UHCI_ALT is not set
# CONFIG_USB_OHCI is not set
# CONFIG_USB_SL811HS_ALT is not set
# CONFIG_USB_SL811HS is not set
# CONFIG_USB_AUDIO is not set
# CONFIG_USB_EMI26 is not set
# CONFIG_USB_MIDI is not set
# CONFIG_USB_STORAGE is not set
# CONFIG_USB_STORAGE_DEBUG is not set
# CONFIG_USB_STORAGE_DATAFAB is not set
# CONFIG_USB_STORAGE_FREECOM is not set
# CONFIG_USB_STORAGE_ISD200 is not set
# CONFIG_USB_STORAGE_DPCM is not set
# CONFIG_USB_STORAGE_HP8200e is not set
# CONFIG_USB_STORAGE_SDDR09 is not set
# CONFIG_USB_STORAGE_SDDR55 is not set
# CONFIG_USB_STORAGE_JUMPSHOT is not set
# CONFIG_USB_ACM is not set
CONFIG_USB_PRINTER=m
# CONFIG_USB_HID is not set
# CONFIG_USB_HIDINPUT is not set
# CONFIG_USB_HIDDEV is not set
# CONFIG_USB_KBD is not set
# CONFIG_USB_MOUSE is not set
# CONFIG_USB_AIPTEK is not set
# CONFIG_USB_WACOM is not set
# CONFIG_USB_KBTAB is not set
# CONFIG_USB_POWERMATE is not set
# CONFIG_USB_DC2XX is not set
# CONFIG_USB_MDC800 is not set
CONFIG_USB_SCANNER=m
# CONFIG_USB_MICROTEK is not set
# CONFIG_USB_HPUSBSCSI is not set
# CONFIG_USB_PEGASUS is not set
# CONFIG_USB_RTL8150 is not set
# CONFIG_USB_KAWETH is not set
# CONFIG_USB_CATC is not set
# CONFIG_USB_CDCETHER is not set
# CONFIG_USB_USBNET is not set
# CONFIG_USB_USS720 is not set

#
# USB Serial Converter support
#
# CONFIG_USB_SERIAL is not set
# CONFIG_USB_RIO500 is not set
# CONFIG_USB_AUERSWALD is not set
# CONFIG_USB_TIGL is not set
# CONFIG_USB_BRLVGER is not set
# CONFIG_USB_LCD is not set

#
# Support for USB gadgets
#
# CONFIG_USB_GADGET is not set

Dotaz: USB support, 2.4.x

Odpovědi