Dotaz: Gentoo a wifi Atheros + madwifi

[svido]

Ahoj, uz druhy den resim problem s wifi Atheros. Prohledal jsem fora, navody a stale se mi nedari wifi rozjet. Moduly by snad meli byt nacteny vsechny, emerge vsech potrebnych balicku byl v poradku. Problem mam v tom, ze v dmesg je chyba wifi%d: unable to attach hardware. Ale pokud nabootuji KNOPPIX 5.1, tak mi funguje.

Kernel:

2.6.20-r3

lsmod:

Module                  Size  Used by
rfcomm                 33896  7 
l2cap                  20096  5 rfcomm
wlan_scan_sta          12416  0 
wlan_tkip              11392  0 
wlan_xauth              1984  0 
wlan_ccmp               7808  0 
wlan_scan_ap            5248  0 
pcmcia                 32344  0 
pcmcia_core            34340  1 pcmcia
ath_pci                84968  0 
ath_rate_sample        13568  1 ath_pci
wlan                  176992  7 wlan_scan_sta,wlan_tkip,wlan_xauth,wlan_ccmp,wlan_scan_ap,ath_pci,ath_rate_sample
ath_hal               216304  2 ath_pci,ath_rate_sample
nvidia               7753112  22 
snd_hda_intel          17504  1 
snd_hda_codec         192256  1 snd_hda_intel
snd_pcm                66632  2 snd_hda_intel,snd_hda_codec
snd_timer              19528  1 snd_pcm
snd                    50216  6 snd_hda_intel,snd_hda_codec,snd_pcm,snd_timer
soundcore               6944  1 snd
snd_page_alloc          8016  2 snd_hda_intel,snd_pcm
sdhci                  16780  0 
mmc_core               22984  1 sdhci
hci_usb                16284  6 
bluetooth              46532  15 rfcomm,l2cap,hci_usb
i2c_core               18880  1 nvidia
shpchp                 30044  0 
pci_hotplug            14344  1 shpchp

dmesg:

ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
wlan: 0.8.4.2 (0.9.2.1)
ath_rate_sample: 1.2 (0.9.2.1)
ath_pci: 0.9.4.5 (0.9.2.1)
...
wifi%d: unable to attach hardware: 'Hardware revision not supported' (HAL status 13)

Odpovědi

[vencour]

Jakej máte přesně hw? U mne to je

04:02.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)

a madwifi-ng 0.9.2.1, zatim vše ok, ať už jsem si jádro patchoval sám v MDV 2006/2007 nebo pužil gentoo a madwifi-ng.

[svido]

U mne je to:

01:00.0 Ethernet controller: Atheros Communications, Inc. AR5006EG 802.11 b/g Wireless PCI Express Adapter (rev 01)

Mam Gentoo 2006.1, AMD64

Kdyz odmaskuji madwifi a naistaluji verzi 0.9.3, jsou chyby uz pri kompilaci modulu a vypis logu je:

Unable to load needed module: ath_rate_sample; no support for automatic module loading<3>Error loading module "ath_rate_sample"

[Zonntar]

Musis do jadra dokompilovat Automatic kernel module loading. (Loadable module support --> [*] Automatic kernel module loading)