Astra 1220s

Zdravim,

vim ze tu tohle tema uz bylo, ale ne presne muj problem.

Mam zaveden modul sg. V dmesg je:

scsi 0:0:0:0: Attached scsi generic sg0 type 0

Zadam

[root@server uzivatel]# echo "scsi add-single-device 0 0 5 0" > /proc/scsi/scsi
[root@server uzivatel]# cat /proc/scsi/scsi
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
  Vendor: USB      Model: BAR              Rev: 2.00
  Type:   Direct-Access                    ANSI  SCSI revision: 02

tj. nic se neulozi. A pak vcelku pochopitelne

[root@server uzivatel]# modprobe g_NCR5380 dtc_3181e=1 ncr_irq=255 ncr_addr=0x280
FATAL: Error inserting g_NCR5380 (/lib/modules/2.6.23-ARCH/kernel/drivers/scsi/g_NCR5380.ko): No such device

Skener jsem rozchodil s puvodni kartou domex, ale tam nebyl pouzitelny, porad se to zasekavalo a tak ... Nyni pouzivam adaptec 1540. Na skener jsem pridal terminaci, kterou domex karta nevyzadovala.

Nevim jak ten skener pridat, jedu podle cca 4 navodu ale nejak to nepomaha ... diky predem za rady ...

Aha, jak to tak vidim, tak to zarizeni je asi moje klicenka ... erm ...

Tak jinak, omylem jsem zavadel modul pro domex, ne adaptec ... takze takhle:

[root@server uzivatel]# modprobe aha1542
FATAL: Error inserting aha1542 (/lib/modules/2.6.23-ARCH/kernel/drivers/scsi/aha1542.ko): No such device

[root@server uzivatel]# dmesg
Configuring Adaptec (SCSI-ID 7) at IO:330, IRQ 11, DMA priority 5
Unable to allocate IRQ for adaptec controller.

A zase nevim co s tim ... :-(

teď to řeším tady:

http://www.abclinuxu.cz/forum/show/138070

Zmenil jsem v BIOSu karty IRQ 11 ktery hazelo chybu UNABLE TO ALLOCATE IRQ na 10 ... a vysledek

[root@server uzivatel]# modprobe aha1542 aha1542=0x330

je dmesg:

Configuring Adaptec (SCSI-ID 7) at IO:330, IRQ 10, DMA priority 5
scsi0 : Adaptec 1542
isa bounce pool size: 16 pages
scsi 0:0:0:0: Trying device reset for target
scsi 0:0:0:0: Trying device reset for target
Clocksource tsc unstable (delta = 4686099070 ns)
Time: acpi_pm clocksource has been installed.
Sent BUS RESET to scsi host 0
scsi 0:0:0:0: Trying device reset for target
scsi 0:0:0:0: scsi: Device offlined - not ready after error recovery
scsi 0:0:1:0: Trying device reset for target
scsi 0:0:1:0: Trying device reset for target
Sent BUS RESET to scsi host 0
scsi 0:0:1:0: Trying device reset for target
scsi 0:0:1:0: scsi: Device offlined - not ready after error recovery
scsi 0:0:2:0: Trying device reset for target
scsi 0:0:2:0: Trying device reset for target
Sent BUS RESET to scsi host 0
scsi 0:0:2:0: Trying device reset for target
scsi 0:0:2:0: scsi: Device offlined - not ready after error recovery
scsi 0:0:3:0: Trying device reset for target
scsi 0:0:3:0: Trying device reset for target
Sent BUS RESET to scsi host 0
scsi 0:0:3:0: Trying device reset for target
scsi 0:0:3:0: scsi: Device offlined - not ready after error recovery
scsi 0:0:4:0: Trying device reset for target
scsi 0:0:4:0: Trying device reset for target
Sent BUS RESET to scsi host 0
scsi 0:0:4:0: Trying device reset for target
scsi 0:0:4:0: scsi: Device offlined - not ready after error recovery
scsi 0:0:5:0: Trying device reset for target
scsi 0:0:5:0: Trying device reset for target
Sent BUS RESET to scsi host 0
scsi 0:0:5:0: Trying device reset for target
scsi 0:0:5:0: scsi: Device offlined - not ready after error recovery
scsi 0:0:6:0: Trying device reset for target
scsi 0:0:6:0: Trying device reset for target
Sent BUS RESET to scsi host 0
scsi 0:0:6:0: Trying device reset for target
scsi 0:0:6:0: scsi: Device offlined - not ready after error recovery

Dotaz: Astra 1220s

Odpovědi