pci_set_power_state() v syslogu

Zdravim, na routeru s debianem se v syslogu objevuje hlaska

Jul 29 07:10:02 router kernel: pci_set_power_state(): 0000:00:0a.0: state=3, current state=5

Dival jsem se do nejstarsiho syslog souboru (tyden stary) je to tam take.

Router bezel bez problemu celou dobu, az vcera spadnul, po restartu nabehnul, ale po 10 hodinach zase spadnul.

Nevim presne co se stalo - v syslogu v dobe nedostupnosti routeru nic neni - takze to muze byt treba problem s napajenim. Chci se zeptat resp. vyloucit, jestli ta hlaska vyse s tim muze nejak souviset ?

V routeru jsou 4 sitovky (3 karty a 1 na desce)

lspci dava toto:

00:09.0 Ethernet controller: Broadcom Corporation BCM4401 100Base-T (rev 01)
Subsystem: ASUSTeK Computer Inc. A7V8X motherboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 169
Region 0: Memory at f1800000 (32-bit, non-prefetchable) [size=8K]
Expansion ROM at f3ef0000 [disabled] [size=16K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

00:0a.0 Ethernet controller: 3Com Corporation 3c900 10BaseT [Boomerang]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max)
Interrupt: pin A routed to IRQ 177
Region 0: I/O ports at d800 [size=64]
[virtual] Expansion ROM at 50040000 [disabled] [size=64K]

00:0b.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
Subsystem: 3Com Corporation 3C905B Fast Etherlink XL 10/100
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 185
Region 0: I/O ports at d400 [size=128]
Region 1: Memory at f1000000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0f.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)
Subsystem: 3Com Corporation 3C905C-TX Fast Etherlink for PC Management NIC
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (2500ns min, 2500ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 169
Region 0: I/O ports at d000 [size=128]
Region 1: Memory at f0800000 (32-bit, non-prefetchable) [size=128]
[virtual] Expansion ROM at 50020000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-

Muze hlaska souviset pouze s tim ze sitovka s id 00:0a.0 nema Power managemenet ?

Ma to nejaky vliv na funkcnost ? - rikam router bezi v teto sestave 2 roky - dekuji

Dotaz: pci_set_power_state() v syslogu