Portál AbcLinuxu, 9. května 2025 17:07
[ 81.638161] usb 2-1: >new SuperSpeed USB device number 2 using xhci_hcd [ 81.658974] usbcore: registered new interface driver uas [ 81.663146] Initializing USB Mass Storage driver... [ 81.663370] scsi6 : usb-storage 2-1:1.0 [ 81.663550] usbcore: registered new interface driver usb-storage [ 81.663553] USB Mass Storage support registered. [ 92.651066] scsi 6:0:0:0: >Direct-Access WD My Passport 0730 1012 PQ: 0 ANSI: 6 [ 92.651517] sd 6:0:0:0: >[sdc] 976707584 512-byte logical blocks: (500 GB/465 GiB) [ 92.651675] sd 6:0:0:0: >[sdc] Write Protect is off [ 92.651682] sd 6:0:0:0: >[sdc] Mode Sense: 47 00 10 08 [ 92.651864] sd 6:0:0:0: >[sdc] No Caching mode page present [ 92.651871] sd 6:0:0:0: >[sdc] Assuming drive cache: write through [ 92.652888] sd 6:0:0:0: >[sdc] No Caching mode page present [ 92.652890] sd 6:0:0:0: >[sdc] Assuming drive cache: write through [ 92.666320] sdc: sdc1 sdc2 [ 92.667233] sd 6:0:0:0: >[sdc] No Caching mode page present [ 92.667236] sd 6:0:0:0: >[sdc] Assuming drive cache: write through [ 92.667238] sd 6:0:0:0: >[sdc] Attached SCSI disk [ 92.774003] usb 2-1: >Device not responding to set address. [ 92.976831] usb 2-1: >Device not responding to set address. [ 93.179907] usb 2-1: >device not accepting address 2, error -71 [ 93.286457] usb 2-1: >Device not responding to set address. [ 93.489494] usb 2-1: >Device not responding to set address. [ 93.692514] usb 2-1: >device not accepting address 2, error -71 [ 93.799171] usb 2-1: >Device not responding to set address. [ 94.002147] usb 2-1: >Device not responding to set address. [ 94.205164] usb 2-1: >device not accepting address 2, error -71 [ 94.311774] usb 2-1: >Device not responding to set address. [ 94.514824] usb 2-1: >Device not responding to set address. [ 94.717855] usb 2-1: >device not accepting address 2, error -71 [ 94.717899] usb 2-1: >USB disconnect, device number 2 [ 94.721016] xhci_hcd 0000:00:14.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800b8064cc0 [ 94.721024] xhci_hcd 0000:00:14.0: >xHCI xhci_drop_endpoint called with disabled ep ffff8800b8064c80 [ 94.827760] usb 2-1: >Device not responding to set address. [ 95.030803] usb 2-1: >Device not responding to set address. [ 95.233807] usb 2-1: >device not accepting address 3, error -71 [ 95.340403] usb 2-1: >Device not responding to set address. [ 95.543579] usb 2-1: >Device not responding to set address. [ 95.746524] usb 2-1: >device not accepting address 4, error -71 [ 95.853114] usb 2-1: >Device not responding to set address. [ 96.056182] usb 2-1: >Device not responding to set address. [ 96.259183] usb 2-1: >device not accepting address 5, error -71 [ 96.365778] usb 2-1: >Device not responding to set address. [ 96.568792] usb 2-1: >Device not responding to set address. [ 96.771846] usb 2-1: >device not accepting address 6, error -71 [ 96.771872] hub 2-0:1.0: >unable to enumerate USB device on port 1 [ 113.633440] usb 2-1: >Device not responding to set address. [ 113.836497] usb 2-1: >Device not responding to set address. [ 114.039515] usb 2-1: >device not accepting address 7, error -71 [ 114.146105] usb 2-1: >Device not responding to set address. [ 114.349168] usb 2-1: >Device not responding to set address. [ 114.552196] usb 2-1: >device not accepting address 8, error -71 [ 114.658758] usb 2-1: >Device not responding to set address. [ 114.861836] usb 2-1: >Device not responding to set address. [ 115.064849] usb 2-1: >device not accepting address 9, error -71 [ 115.171448] usb 2-1: >Device not responding to set address. [ 115.374483] usb 2-1: >Device not responding to set address. [ 115.577517] usb 2-1: >device not accepting address 10, error -71 [ 115.577539] hub 2-0:1.0: >unable to enumerate USB device on port 1a to je všechno, disk se zastaví a já můžu akorát přepojit disk na USB2.0 port. Nevzdal jsem to a zjišťoval dál, bootnul jsem do opensuse s kernelem 3.4 a tam disk fungoval. Zkusim jsem zkompilovat vanilla kernel 3.6 a tam jsem dostal úplně stejnou chybu jako v archu. Když jsem googlil, nenarazil jsem na žádné zmínky o tom, že by byly s USB 3.0 nějaké výrazné problémy. Připojil jsem tedy na USB 3.0 port jiný disk, novější generace ( třeba tady http://www.czc.cz/wd-my-passport-generation-2-1tb-cerna/108413/produkt ) a vše běželo jak má, prostě žádný problém. Vůbec nevím jak tento problém řešit, jestli někam dát bugreport a jaké další info poskytnout. Je to tedy závislé na HW disku a objevilo se to pravděpodobně někde ve verzi 3.4 až 3.5. Kdyby někdo měl nápad jak vyřešit tento problém, sem s nim. Díky za všechny nápady, všechny další informace není problém poskytnout, stačí říct jaké...
Skús pozrieť typ radiča, ktorý používa tvoj notebook či nemá problémy s linuxom. Ceľkom realna možnosť je, že problém je v USB radiči, ktorý sa prejavuje u staršej verzie. Tiež sa nedá vylúčiť zmena v komunikačnom protokole USB3. Kedy sa začali problémy prejavovať ? Hneď po kúpeni disku alebo po nejakej úprave systému ?
[14219.070919] xhci_hcd 0000:00:14.0: >remove, state 4 [14219.070932] usb usb2: >USB disconnect, device number 1 [14219.071041] xHCI xhci_drop_endpoint called for root hub [14219.071044] xHCI xhci_check_bandwidth called for root hub [14219.071251] xhci_hcd 0000:00:14.0: >USB bus 2 deregistered [14219.071266] xhci_hcd 0000:00:14.0: >remove, state 1 [14219.071274] usb usb1: >USB disconnect, device number 1 [14219.071278] usb 1-2: >USB disconnect, device number 2 [14219.092809] xhci_hcd 0000:00:14.0: >Slot 1 endpoint 2 not removed from BW list! [14219.092819] xhci_hcd 0000:00:14.0: >Slot 1 endpoint 4 not removed from BW list! [14219.092938] xHCI xhci_drop_endpoint called for root hub [14219.092942] xHCI xhci_check_bandwidth called for root hub [14219.093282] xhci_hcd 0000:00:14.0: >USB bus 1 deregisteredpřidám modul zpět...
[14287.742363] xhci_hcd 0000:00:14.0: >power state changed by ACPI to D0 [14287.742374] xhci_hcd 0000:00:14.0: >power state changed by ACPI to D0 [14287.742467] xhci_hcd 0000:00:14.0: >setting latency timer to 64 [14287.742474] xhci_hcd 0000:00:14.0: >xHCI Host Controller [14287.742485] xhci_hcd 0000:00:14.0: >new USB bus registered, assigned bus number 1 [14287.742603] xhci_hcd 0000:00:14.0: >cache line size of 64 is not supported [14287.742614] xhci_hcd 0000:00:14.0: >irq 16, io mem 0xf2520000 [14287.742706] xhci_hcd 0000:00:14.0: >irq 40 for MSI/MSI-X [14287.743011] xHCI xhci_add_endpoint called for root hub [14287.743014] xHCI xhci_check_bandwidth called for root hub [14287.743064] hub 1-0:1.0: >USB hub found [14287.743076] hub 1-0:1.0: >4 ports detected [14287.747075] xhci_hcd 0000:00:14.0: >xHCI Host Controller [14287.747089] xhci_hcd 0000:00:14.0: >new USB bus registered, assigned bus number 2 [14287.747542] xHCI xhci_add_endpoint called for root hub [14287.747547] xHCI xhci_check_bandwidth called for root hub [14287.747675] hub 2-0:1.0: >USB hub found [14287.747693] hub 2-0:1.0: >4 ports detected [14288.100061] usb 1-2: >new low-speed USB device number 2 using xhci_hcd [14288.137172] usb 1-2: >ep 0x81 - rounding interval to 64 microframes, ep desc says 80 microframes [14288.137183] usb 1-2: >ep 0x82 - rounding interval to 64 microframes, ep desc says 80 microframes [14288.147164] input: Genius Multimedia Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.0/input/input21 [14288.147425] hid-generic 0003:0458:0708.0006: >input,hidraw0: USB HID v1.11 Keyboard [Genius Multimedia Keyboard] on usb-0000:00:14.0-2/input0 [14288.161536] input: Genius Multimedia Keyboard as /devices/pci0000:00/0000:00:14.0/usb1/1-2/1-2:1.1/input/input22 [14288.161966] hid-generic 0003:0458:0708.0007: >input,hiddev0,hidraw1: USB HID v1.11 Device [Genius Multimedia Keyboard] on usb-0000:00:14.0-2/input1 [14288.266419] usb 2-1: >new SuperSpeed USB device number 2 using xhci_hcd [14288.281113] scsi10 : usb-storage 2-1:1.0a potom už je zase výpis, že je disk připojen a zase stejná chyba jako jsem popisoval. Nebo je to myšleno snad jinak?
Tiskni
Sdílej:
ISSN 1214-1267, (c) 1999-2007 Stickfish s.r.o.