Portál AbcLinuxu, 5. května 2025 03:08
mode2 -d /dev/lirc0nic nedetekuje
dmesg|grep lirc [ 6.137496] lirc_dev: IR Remote Control driver registered, major 244 [ 6.292825] lirc_rpi: module is from the staging directory, the quality is unknown, you have been warned. [ 7.463550] lirc_rpi: auto-detected active high receiver on GPIO pin 18 [ 7.577579] lirc_rpi lirc_rpi: lirc_dev: driver lirc_rpi registered at minor = 0 [ 7.663109] lirc_rpi: driver registered! [ 11.249510] input: lircd as /devices/virtual/input/input4 [ 576.160801] input: lircd as /devices/virtual/input/input5 [ 596.581667] input: lircd as /devices/virtual/input/input6 lsmod|grep lirc lirc_rpi 8602 3 lirc_dev 11060 1 lirc_rpi rc_core 23030 1 lirc_devProvedl jsem přeinstalaci balícků pro lirc, nastavil jsem vše podle návodů a stále nic. Nerozumím ve výpisu dmesg posledním třem řádkům. TSOP1736 je 100% v pořádku. Soubory /etc/lirc/hardvare.conf a lircd.conf jsou nezměněné od doby před aktualizací Dík za nasměrování
.
Pokud je lirc_rpi ze staging, tak v něm může být bug (i když o tom pochybuju, jestli to je ten co myslím, tak jen ošetřuje interrupt na GPIO a posílá z něj timestamp do lirc vrstvy).
[Jen blbej nápad] Taky by mohlo bejt GPIO (mux) v nový verzi kernelu jinak definovaný [/]
#############################################################
WARNING: This update bumps to rpi-4.1.y linux tree
Be aware there could be compatibility issues with some drivers
Discussion here:
https://www.raspberrypi.org/forums/viewtopic.php?f=29&t=113753
##############################################################
# Uncomment this to enable the lirc-rpi module
#dtoverlay=lirc-rpi
hexdump /dev/lirc0na mě vyhodí, že zařízení je již používáno. Tady je komplet dmesg.
[ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.1.5+ (dc4@dc4-XPS13-9333) (gcc version 4.8.3 20140303 (prerelease) (crosstool-NG linaro-1.13.1+bzr2650 - Linaro GCC 2014.03) ) #809 PREEMPT Thu Aug 13 00:30:15 BST 2015 [ 0.000000] CPU: ARMv6-compatible processor [410fb767] revision 7 (ARMv7), cr=00c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache [ 0.000000] Machine model: Raspberry Pi Model B Rev 2 [ 0.000000] cma: Reserved 8 MiB at 0x1b800000 [ 0.000000] Memory policy: Data cache writeback [ 0.000000] On node 0 totalpages: 114688 [ 0.000000] free_area_init_node: node 0, pgdat c088beac, node_mem_map db403000 [ 0.000000] Normal zone: 1008 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 114688 pages, LIFO batch:31 [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 113680 [ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1280 bcm2708_fb.fbheight=1024 bcm2708.boardrev=0xe bcm2708.serial=0xba647df9 smsc95xx.macaddr=B8:27:EB:64:7D:F9 bcm2708_fb.fbswap=1 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x1ec00000 vc_mem.mem_size=0x20000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 cgroup_enable=memory elevator=deadline rootwait [ 0.000000] Enabling memory control group subsystem [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 436508K/458752K available (6132K kernel code, 490K rwdata, 1780K rodata, 348K init, 720K bss, 14052K reserved, 8192K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xdc800000 - 0xff000000 ( 552 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdc000000 ( 448 MB) [ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB) [ 0.000000] .text : 0xc0008000 - 0xc07c2388 (7913 kB) [ 0.000000] .init : 0xc07c3000 - 0xc081a000 ( 348 kB) [ 0.000000] .data : 0xc081a000 - 0xc0894824 ( 491 kB) [ 0.000000] .bss : 0xc0894824 - 0xc09489b0 ( 721 kB) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Additional per-CPU info printed with stalls. [ 0.000000] NR_IRQS:522 [ 0.000000] clocksource stc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275 ns [ 0.000015] sched_clock: 32 bits at 1000kHz, resolution 1000ns, wraps every 2147483647500ns [ 0.000056] Switching to timer-based delay loop, resolution 1000ns [ 0.000342] Console: colour dummy device 80x30 [ 0.001750] console [tty1] enabled [ 0.001813] Calibrating delay loop (skipped), value calculated using timer frequency.. 2.00 BogoMIPS (lpj=10000) [ 0.001909] pid_max: default: 32768 minimum: 301 [ 0.002281] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.002362] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.003458] Initializing cgroup subsys blkio [ 0.003557] Initializing cgroup subsys memory [ 0.003671] Initializing cgroup subsys devices [ 0.003746] Initializing cgroup subsys freezer [ 0.003812] Initializing cgroup subsys net_cls [ 0.003933] CPU: Testing write buffer coherency: ok [ 0.004062] ftrace: allocating 19769 entries in 58 pages [ 0.110949] Setting up static identity map for 0x81c0 - 0x81f8 [ 0.113738] devtmpfs: initialized [ 0.124547] VFP support v0.3: implementor 41 architecture 1 part 20 variant b rev 5 [ 0.124984] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.127029] pinctrl core: initialized pinctrl subsystem [ 0.127982] NET: Registered protocol family 16 [ 0.133583] DMA: preallocated 4096 KiB pool for atomic coherent allocations [ 0.135190] bcm2708.uart_clock = 3000000 [ 0.140762] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers. [ 0.140859] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.141073] Serial: AMBA PL011 UART driver [ 0.141389] 20201000.uart: ttyAMA0 at MMIO 0x20201000 (irq = 83, base_baud = 0) is a PL011 rev2 [ 0.530301] console [ttyAMA0] enabled [ 0.534724] bcm2835-mbox 2000b880.mailbox: mailbox enabled [ 0.602926] bcm2708-dmaengine 20007000.dma: DMA legacy API manager at f2007000, dmachans=0x7f35 [ 0.612490] bcm2708-dmaengine 20007000.dma: Load BCM2835 DMA engine driver [ 0.619432] bcm2708-dmaengine 20007000.dma: dma_debug:0 [ 0.625645] SCSI subsystem initialized [ 0.629825] usbcore: registered new interface driver usbfs [ 0.635569] usbcore: registered new interface driver hub [ 0.641107] usbcore: registered new device driver usb [ 0.647224] raspberrypi-firmware soc:firmware: Attached to firmware from 2015-08-15 17:48 [ 0.683040] Switched to clocksource stc [ 0.734543] FS-Cache: Loaded [ 0.737862] CacheFiles: Loaded [ 0.757564] NET: Registered protocol family 2 [ 0.763621] TCP established hash table entries: 4096 (order: 2, 16384 bytes) [ 0.770823] TCP bind hash table entries: 4096 (order: 2, 16384 bytes) [ 0.777636] TCP: Hash tables configured (established 4096 bind 4096) [ 0.784203] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.790106] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.796844] NET: Registered protocol family 1 [ 0.801877] RPC: Registered named UNIX socket transport module. [ 0.808008] RPC: Registered udp transport module. [ 0.812757] RPC: Registered tcp transport module. [ 0.817544] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.825410] hw perfevents: enabled with armv6_1176 PMU driver, 3 counters available [ 0.834669] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.857135] VFS: Disk quotas dquot_6.6.0 [ 0.861541] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 0.871253] FS-Cache: Netfs 'nfs' registered for caching [ 0.878363] NFS: Registering the id_resolver key type [ 0.883713] Key type id_resolver registered [ 0.887948] Key type id_legacy registered [ 0.895961] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.904069] io scheduler noop registered [ 0.908085] io scheduler deadline registered (default) [ 0.913863] io scheduler cfq registered [ 0.920286] BCM2708FB: allocated DMA memory 5bc00000 [ 0.925641] BCM2708FB: allocated DMA channel 0 @ f2007000 [ 0.948750] Console: switching to colour frame buffer device 160x64 [ 0.968702] Serial: 8250/16550 driver, 0 ports, IRQ sharing disabled [ 0.976984] vc-cma: Videocore CMA driver [ 0.981045] vc-cma: vc_cma_base = 0x00000000 [ 0.986025] vc-cma: vc_cma_size = 0x00000000 (0 MiB) [ 0.991558] vc-cma: vc_cma_initial = 0x00000000 (0 MiB) [ 0.997595] vc-mem: phys_addr:0x00000000 mem_base=0x1ec00000 mem_size:0x20000000(512 MiB) [ 1.026914] brd: module loaded [ 1.039792] loop: module loaded [ 1.044472] vchiq: vchiq_init_state: slot_zero = 0xdbc80000, is_master = 0 [ 1.053940] Loading iSCSI transport class v2.0-870. [ 1.060556] usbcore: registered new interface driver smsc95xx [ 1.066834] dwc_otg: version 3.00a 10-AUG-2012 (platform bus) [ 1.273126] Core Release: 2.80a [ 1.276392] Setting default values for core params [ 1.281331] Finished setting default values for core params [ 1.487358] Using Buffer DMA mode [ 1.490788] Periodic Transfer Interrupt Enhancement - disabled [ 1.496802] Multiprocessor Interrupt Enhancement - disabled [ 1.502507] OTG VER PARAM: 0, OTG VER FLAG: 0 [ 1.507018] Dedicated Tx FIFOs mode [ 1.511138] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xdbc14000 dma = 0x5bc14000 len=9024 [ 1.521279] FIQ FSM acceleration enabled for : [ 1.521279] Non-periodic Split Transactions [ 1.521279] Periodic Split Transactions [ 1.521279] High-Speed Isochronous Endpoints [ 1.538448] dwc_otg: Microframe scheduler enabled [ 1.538577] WARN::hcd_init_fiq:412: FIQ on core 0 at 0xc042394c [ 1.544643] WARN::hcd_init_fiq:413: FIQ ASM at 0xc0423c24 length 36 [ 1.551073] WARN::hcd_init_fiq:438: MPHI regs_base at 0xdc896000 [ 1.557344] dwc_otg 20980000.usb: DWC OTG Controller [ 1.567606] dwc_otg 20980000.usb: new USB bus registered, assigned bus number 1 [ 1.580207] dwc_otg 20980000.usb: irq 32, io mem 0x00000000 [ 1.590986] Init: Port Power? op_state=1 [ 1.600067] Init: Power Port (0) [ 1.608784] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 1.620768] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 1.633131] usb usb1: Product: DWC OTG Controller [ 1.642863] usb usb1: Manufacturer: Linux 4.1.5+ dwc_otg_hcd [ 1.653596] usb usb1: SerialNumber: 20980000.usb [ 1.664420] hub 1-0:1.0: USB hub found [ 1.673515] hub 1-0:1.0: 1 port detected [ 1.683365] dwc_otg: FIQ enabled [ 1.683394] dwc_otg: NAK holdoff enabled [ 1.683407] dwc_otg: FIQ split-transaction FSM enabled [ 1.683474] Module dwc_common_port init [ 1.684060] usbcore: registered new interface driver usb-storage [ 1.695890] mousedev: PS/2 mouse device common for all mice [ 1.707921] bcm2835-cpufreq: min=700000 max=700000 [ 1.718486] sdhci: Secure Digital Host Controller Interface driver [ 1.729907] sdhci: Copyright(c) Pierre Ossman [ 1.740086] mmc-bcm2835 20300000.mmc: mmc_debug:0 mmc_debug2:0 [ 1.751068] mmc-bcm2835 20300000.mmc: DMA channels allocated [ 1.793536] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.812721] ledtrig-cpu: registered to indicate activity on CPUs [ 1.824193] hidraw: raw HID events driver (C) Jiri Kosina [ 1.838349] usbcore: registered new interface driver usbhid [ 1.851132] usbhid: USB HID core driver [ 1.862628] Initializing XFRM netlink socket [ 1.873294] Indeed it is in host mode hprt0 = 00021501 [ 1.883649] NET: Registered protocol family 17 [ 1.903329] Key type dns_resolver registered [ 1.920655] mmc0: host does not support reading read-only switch, assuming write-enable [ 1.934921] registered taskstats version 1 [ 1.963468] vc-sm: Videocore shared memory driver [ 1.975521] mmc0: new high speed SDHC card at address b368 [ 1.986207] [vc_sm_connected_init]: start [ 2.013374] mmcblk0: mmc0:b368 FFFFF 7.51 GiB [ 2.024017] [vc_sm_connected_init]: end - returning 0 [ 2.041340] mmcblk0: p1 p2 [ 2.071435] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null) [ 2.085193] VFS: Mounted root (ext4 filesystem) readonly on device 179:2. [ 2.098985] devtmpfs: mounted [ 2.108849] Freeing unused kernel memory: 348K (c07c3000 - c081a000) [ 2.163186] usb 1-1: new high-speed USB device number 2 using dwc_otg [ 2.177423] Indeed it is in host mode hprt0 = 00001101 [ 2.393760] usb 1-1: New USB device found, idVendor=0424, idProduct=9512 [ 2.408785] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.423132] hub 1-1:1.0: USB hub found [ 2.433308] hub 1-1:1.0: 3 ports detected [ 2.723242] usb 1-1.1: new high-speed USB device number 3 using dwc_otg [ 2.833782] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00 [ 2.847568] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [ 2.866459] smsc95xx v1.0.4 [ 2.943536] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-20980000.usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:64:7d:f9 [ 3.053435] usb 1-1.2: new low-speed USB device number 4 using dwc_otg [ 3.205404] usb 1-1.2: New USB device found, idVendor=1c4f, idProduct=0002 [ 3.225045] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 3.239612] usb 1-1.2: Product: USB Keyboard [ 3.252397] usb 1-1.2: Manufacturer: SIGMACHIP [ 3.285528] input: SIGMACHIP USB Keyboard as /devices/platform/soc/20980000.usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:1C4F:0002.0001/input/input0 [ 3.363724] hid-generic 0003:1C4F:0002.0001: input,hidraw0: USB HID v1.10 Keyboard [SIGMACHIP USB Keyboard] on usb-20980000.usb-1.2/input0 [ 3.425162] input: SIGMACHIP USB Keyboard as /devices/platform/soc/20980000.usb/usb1/1-1/1-1.2/1-1.2:1.1/0003:1C4F:0002.0002/input/input1 [ 3.513724] hid-generic 0003:1C4F:0002.0002: input,hidraw1: USB HID v1.10 Device [SIGMACHIP USB Keyboard] on usb-20980000.usb-1.2/input1 [ 3.633236] usb 1-1.3: new high-speed USB device number 5 using dwc_otg [ 3.764045] usb 1-1.3: New USB device found, idVendor=1a40, idProduct=0101 [ 3.793316] usb 1-1.3: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 3.817495] usb 1-1.3: Product: USB 2.0 Hub [ 3.839268] hub 1-1.3:1.0: USB hub found [ 3.863626] hub 1-1.3:1.0: 4 ports detected [ 4.183271] usb 1-1.3.2: new low-speed USB device number 6 using dwc_otg [ 4.247249] udevd[159]: starting version 175 [ 4.329494] usb 1-1.3.2: New USB device found, idVendor=192f, idProduct=0916 [ 4.359294] usb 1-1.3.2: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 4.393361] usb 1-1.3.2: Product: USB Optical Mouse [ 4.455611] input: USB Optical Mouse as /devices/platform/soc/20980000.usb/usb1/1-1/1-1.3/1-1.3.2/1-1.3.2:1.0/0003:192F:0916.0003/input/input2 [ 4.524148] hid-generic 0003:192F:0916.0003: input,hidraw2: USB HID v1.11 Mouse [USB Optical Mouse] on usb-20980000.usb-1.3.2/input0 [ 4.653262] usb 1-1.3.4: new high-speed USB device number 7 using dwc_otg [ 4.795425] usb 1-1.3.4: New USB device found, idVendor=05e3, idProduct=0608 [ 4.839219] usb 1-1.3.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 4.886722] usb 1-1.3.4: Product: USB2.0 Hub [ 4.916387] hub 1-1.3.4:1.0: USB hub found [ 4.952878] hub 1-1.3.4:1.0: 4 ports detected [ 5.263248] usb 1-1.3.4.1: new high-speed USB device number 8 using dwc_otg [ 5.453575] usb 1-1.3.4.1: New USB device found, idVendor=0c45, idProduct=6340 [ 5.493299] usb 1-1.3.4.1: New USB device strings: Mfr=2, Product=1, SerialNumber=0 [ 5.543388] usb 1-1.3.4.1: Product: Sweex ViewPlus Webcam USB [ 5.577966] usb 1-1.3.4.1: Manufacturer: Sonix Technology Co., Ltd. [ 5.713237] usb 1-1.3.4.4: new high-speed USB device number 9 using dwc_otg [ 5.865546] usb 1-1.3.4.4: New USB device found, idVendor=05e3, idProduct=0608 [ 5.893333] usb 1-1.3.4.4: New USB device strings: Mfr=0, Product=1, SerialNumber=0 [ 5.923296] usb 1-1.3.4.4: Product: USB2.0 Hub [ 5.954670] hub 1-1.3.4.4:1.0: USB hub found [ 5.978282] hub 1-1.3.4.4:1.0: 4 ports detected [ 6.117636] lirc_dev: IR Remote Control driver registered, major 244 [ 6.289323] lirc_rpi: module is from the staging directory, the quality is unknown, you have been warned. [ 7.091645] random: nonblocking pool is initialized [ 7.473390] lirc_rpi: auto-detected active high receiver on GPIO pin 18 [ 7.572314] lirc_rpi lirc_rpi: lirc_dev: driver lirc_rpi registered at minor = 0 [ 7.669581] lirc_rpi: driver registered! [ 7.943306] spi spi0.0: setting up native-CS0 as GPIO 8 [ 8.094204] spi spi0.1: setting up native-CS1 as GPIO 7 [ 8.231178] bcm2708_i2c 20804000.i2c: BSC1 Controller at 0x20804000 (irq 79) (baudrate 100000) [ 9.644522] media: Linux media interface: v0.10 [ 9.743766] Linux video capture interface: v2.00 [ 9.861756] uvcvideo: Found UVC 1.00 device Sweex ViewPlus Webcam USB (0c45:6340) [ 9.945561] input: Sweex ViewPlus Webcam USB as /devices/platform/soc/20980000.usb/usb1/1-1/1-1.3/1-1.3.4/1-1.3.4.1/1-1.3.4.1:1.0/input/input3 [ 9.970108] usbcore: registered new interface driver uvcvideo [ 9.983330] USB Video Class driver (1.1.1) [ 11.201408] input: lircd as /devices/virtual/input/input4 [ 14.259346] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 14.836613] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null) [ 22.682473] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 26.574144] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 28.138973] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xCDE1 [ 34.095380] Adding 102396k swap on /var/swap. Priority:-1 extents:2 across:2134012k SSFS [ 39.239867] uart-pl011 20201000.uart: no DMA platform dataV /etc/lirc/hardware.conf jsem se překlep. "jeste v /etc/config.txt je tento radek, mas ho odkomentovany? # Uncomment this to enable the lirc-rpi module #dtoverlay=lirc-rpi" Určitě v /etc/config.txt ? Tam nic nemám, ale odkomentováno mám v /boot/config.txt Ještě jednou děkuji za pomoc. Venca
ls /lib/modules -l drwxr-xr-x 3 root root 4096 pro 21 2014 3.12.35+ drwxr-xr-x 3 root root 4096 úno 8 2015 3.18.6+ drwxr-xr-x 3 root root 4096 úno 8 2015 3.18.6-v7+ drwxr-xr-x 3 root root 4096 srp 16 13:47 4.1.5+ drwxr-xr-x 3 root root 4096 srp 16 13:47 4.1.5-v7+ uname -a Linux raspberrypi 4.1.5+ #809 PREEMPT Thu Aug 00:30:15 BST 2015 armv6l GNU/LinuxJestli se někde nemusí nastavit odkud má lirc muduly načítat. Dík
insmod /cesta/lirc_rpi.ko debug=1Jinak v tom dmesg výpisu se ti ten modul najde a načte. Můj upravený GPIO driver má tenhle výstup:
[ 2578.086182] Registered IR keymap rc-empty [ 2578.104451] input: gpio_ir_recv as /devices/platform/gpio-rc-recv/rc/rc0/input4 [ 2578.116132] rc0: gpio_ir_recv as /devices/platform/gpio-rc-recv/rc/rc0 [ 2578.128183] rc rc0: lirc_dev: driver ir-lirc-codec (gpio-rc-recv) registered at minor = 0 [ 2578.139821] input: MCE IR Keyboard/Mouse (gpio-rc-recv) as /devices/virtual/input/input5a normálně plive timestamp data z /dev/lirc0. A jsou načtený moduly: rc_core, lirc_dev, ir_*_decoder
Tiskni
Sdílej:
ISSN 1214-1267, (c) 1999-2007 Stickfish s.r.o.