ABCLinux a tablet WACOM Graphire3

Na distribucii abclinux sa snazim sprevadzkovat graficky tablet WACOM Graphire3 (pripojeny na USB port). Bez zasahu sa tablet sprava ako obycajna USB mys. USB Viewer ho idetifikuje ako CTE-430-UV3.1-4. Podla HowTo som skusil nasledujuci postup:

1. pomocou modprobe som natiahol moduly evdev a wacom (bez akychkolvek parametrov)

2. Upravil som konfiguracny subor /etc/X11/XFree-4: Do sekcie ServerLayuot som doplnil:

        InputDevice    "stylus" "AlwaysCore"
        InputDevice    "cursor" "AlwaysCore"
        InputDevice    "eraser" "AlwaysCore"

Do sekcie Module:

        Load  "wacom"

Vytvoril som nasledovne sekcie s InputDevice:

Section "InputDevice"
        Identifier "cursor"
        Driver "wacom" 
        Option "Device" "/dev/input/event0"
        Option "Type" "cursor"
        Option "Mode" "relative"
        Option "Speed" "12.0"
        Option "USB" "on"
EndSection

Section "InputDevice"
        Driver "wacom"
        Identifier "stylus"
        Option "Device" "/dev/input/event0"
        Option "Type" "stylus"
        Option "Mode" "absolute"
        Option "USB" "on"
        Option "DeviceName" "stylus"
        Option "AlwaysCore" "on"
        Option "Tilt" "on"
EndSection

Section "InputDevice"
        Driver "wacom"
        Identifier "eraser"
        Option "Device" "/dev/input/event0"
        Option "Type" "eraser"
        Option "Mode" "absolute"
        Option "USB" "on"
        Option "DeviceName" "eraser"
        Option "Tilt" "on"
EdSection

Po restarte XFree sa uz kurzor pomocou pera, gumy, ani mysi tabletu nepohne, ale z menu gimpu je mozne najst aktivne zalozky s Input Devices. Z konzoly, z ktorej startuje XFree je mozne vidiet nasledovne hlasenia:

.
.
.
wacom: relative event receved (0)!!!
wacom: relative event receved (1)!!!
Error reading wacom device: Invalid argument
.
.
.

... a tak stale dookola

Predpokladam, ze som len pri konfiguracii nieco zabudol, alebo spravil chybne, alebo nema abclinux/knoppix nieco, co potrebuje tablet k tomu, aby fungoval v plnom rozsahu?

Skusal som este pre kazdu polozku v sekcii InputDevices tykajucu sa tabletu doplnit riadok, tak ako som to nasiel v jednom priklade pre kofiguracny subor pre Wacom Graphire2:

Option "SendCoreEvents" "true"

Nepomohlo ani toto, takze chyba musi byt niekde inde. V man wacom tato volba ani nie je popisana.

Pre upresnenie este uvadzam relevantnu cast vypisu z /var/log/XFree86.0.log:

XFree86 Version 4.3.0 (Debian 4.3.0-0ds4 20030416150820 dstone@aedificator)
Release Date: 18 March 2003
X Protocol Version 11, Revision 0, Release 6.6
Build Operating System: Linux 2.4.21-pre5 i686 [ELF] 
Build Date: 16 April 2003
        Before reporting problems, check http://www.XFree86.Org/
        to make sure that you have the latest version.
Module Loader present
OS Kernel: Linux version 2.4.22-xfs (root@Knoppix) (gcc version 2.95.4 20011002 
(Debian prerelease)) #1 SMP Fr Sep 19 17:55:45 CEST 2003 
Markers: (--) probed, (**) from config file, (==) default setting,
         (++) from command line, (!!) notice, (II) informational,
         (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/XFree86.0.log", Time: Thu Jun 24 14:34:11 2004
(==) Using config file: "/etc/X11/XF86Config-4"
(==) ServerLayout "XFree86 Configured"
(**) |-->Screen "Screen0" (0)
(**) |   |-->Monitor "Monitor0"
(**) |   |-->Device "Card0"
(**) |-->Input Device "Keyboard0"
.
.
.
(**) |-->Input Device "PS/2 Mouse"
(**) |-->Input Device "stylus"
(**) |-->Input Device "cursor"
(**) |-->Input Device "eraser"
.
.
.
(**) Option "AlwaysCore"
(**) stylus: always reports core events
(**) stylus serial device is /dev/input/event0
(**) stylus is in absolute mode
(**) Option "Tilt" "on"
(**) Option "USB" "on"
(**) stylus: reading USB link
(**) stylus: resol x = 1270
(**) Option "BaudRate" "9600"
(**) stylus: serial speed 9600
(**) Option "AlwaysCore"
(**) cursor: always reports core events
(**) cursor serial device is /dev/input/event0
(**) cursor is in relative mode
(**) Option "USB" "on"
(**) cursor: reading USB link
(**) cursor: resol x = 1270
(**) Option "BaudRate" "9600"
(**) cursor: serial speed 9600
(**) Option "AlwaysCore"
(**) eraser: always reports core events
(**) eraser serial device is /dev/input/event0
(**) eraser is in absolute mode
(**) Option "Tilt" "on"
(**) Option "USB" "on"
(**) eraser: reading USB link
(**) eraser: resol x = 1270
(**) Option "BaudRate" "9600"
(**) eraser: serial speed 9600
(II) XINPUT: Adding extended input device "eraser" (type: Wacom Eraser)
(II) XINPUT: Adding extended input device "cursor" (type: Wacom Cursor)
(II) XINPUT: Adding extended input device "stylus" (type: Wacom Stylus)
(II) XINPUT: Adding extended input device "PS/2 Mouse" (type: MOUSE)
(II) Server_Terminate keybinding not found
(**) Option "Device" "/dev/input/event0"
(==) Wacom Kernel Input device name: "WACOM CTE-430-UV3.1-4"
(==) Wacom tablet maximum X=0 maximum Y=0 X resolution=0 Y resolution=0 suppress
=0
(==) Wacom tablet top X=0 top Y=0 bottom X=0 bottom Y=0
(==) Wacom tablet top X=0 top Y=0 bottom X=0 bottom Y=0
(==) Wacom tablet top X=0 top Y=0 bottom X=0 bottom Y=0

Pokial nepohnem nastrojom tabletu, vypis konci takto. Z vypisu sa zda, ze fungovat by to malo, nie su hlasene ziadne chyby, akurat su mi divne tie suradnice top X=0 top Y=0 bottom X=0 bottom Y=0. Predpokladam, ze chyba bude niekde tu. Skusim este nastavit BottomX a BottomY. Az potom, ked pohnem nastrojom, na konzolu z ktorej startuje XFree86 sa zacne vypisovat:

wacom: relative event received (0)!!!
wacom: relative event received (1)!!!

24.6.2004 17:23 marian
Rozbalit Rozbalit vše Re: ABCLinux a tablet WACOM Graphire3

Zial, nepomohlo ani rucne zadanie BottomX a BottomY pomocou Option "BottomX" a Option "BottomY". Skusal som nastavit na rozne hodnoty, ale vysledok bol vzdy (samozrejme, menili sa hodnoty v zatvorke pre BottomX a Y) takyto:

Wacom invalid BottomX (6400) reseting to 0
Wacom invalid BottomY (5120) reseting to 0
(==) Wacom tablet top X=0 top Y=0 bottom X=0 bottom Y=0

Pouzivam rozlisenie na 17" LCD displeji 1280x1024. Pre hodnoty BottomX a BottomY som mal nastavene aj tieto hodnoty, ale vysledok bol rovnaky. Ako tak pozeram na polozku resolution, tiez nie je vo vysledku nastavena dobre -- pocas startu XFree86 je snaha o nastavenie jej hodnoty na:

(**) stylus: resol x = 1270

Vo vysledku je vsak nastavena hodnota resolution na 0:

(==) Wacom tablet maximum X=0 maximum Y=0 X resolution=0 Y resolution=0 suppress=0

Dotaz: ABCLinux a tablet WACOM Graphire3

Odpovědi