Dotaz: msg: cs: pcmcia_socket0: unable to apply power.

[koza]

zdravim, doma mi bezi router na gentoo dist:
Linux gejt 2.6.12.3 #19 SMP Thu Aug 18 19:31:40 GMT 2005 i686 Pentium III
Bezi mi natom 3 sitove komponenty, resp bezi dva:
0000:01:0b.0 Network controller: Intersil Corporation Prism 2.5 Wavelan chipset (rev 01) /XI-626/
0000:01:0f.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78) /3c905/,

jedna je XI-325 a je zapojena v PCI2PCMCIA /0000:01:0d.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)/ po spojazdneni ma sluzit ako priw. AP v baracku.. v messages po starte pcmcia zahlasi :
Aug 19 10:21:57 gejt cardmgr[9740]: watching 1 socket
Aug 19 10:21:57 gejt cs: IO port probe 0xc00-0xcff: clean.
Aug 19 10:21:57 gejt cs: IO port probe 0x800-0x8ff: clean.
Aug 19 10:21:57 gejt cs: IO port probe 0x100-0x4ff: excluding 0x3f8-0x4bf 0x4d0-0x4d7
Aug 19 10:21:57 gejt cs: IO port probe 0xa00-0xaff: clean.
Aug 19 10:21:57 gejt cs: pcmcia_socket0: unable to apply power.

vyguglil som stranku s "riesenim":
http://pcmcia.arm.linux.org.uk/ , a dostal som sa k zkompilovaniu cbdump a vypisu zregistov /Ricoh Co Ltd RL5c475/,
nasledne napisal:
gejt opt # setpci -s 0d.0 0x80.l
00000001
gejt opt # setpci -s 0d.0 0x80.l=0x08000001

nic vsak nepomohlo porestarte, znama hlaska v messagess:
cs: pcmcia_socket0: unable to apply power.

sedim nad tym uz tyzden a neviem sa dopatrat k rieseniu, neviem si rady, pokial ste riesili obdobny problem pomozte. d~ koza

doplnenie udajov...

.config: http://localhost.sk/~koza//temp/linux/config.txt
lspci -vv: http://localhost.sk/~koza//temp/linux/lspci.txt
lsmod: http://localhost.sk/~koza//temp/linux/lsmod.txt

Odpovědi

[koza]

Niekde som sa docital ze Ricoh Co Ltd RL5c475 vyzaduje irq11 ci vysie nez 10. Moj bios ani po udatu nema moznost priradovat prerusenie. Preto som prehadzoval medzi slotmi az priradil 11

cardctl hned napisal nieco nove: # cardctl status Socket 0: 5V 16-bit PC Card function 0: [ready]

a v dmesg nova sprava od cs: cs: IO port probe 0xc00-0xcff: clean. cs: IO port probe 0x800-0x8ff: clean. cs: IO port probe 0x100-0x4ff: excluding 0x3f8-0x4bf 0x4d0-0x4d7 cs: IO port probe 0xa00-0xaff: clean. cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff >>>> cs: warning: no high memory space available! <<<<<

a nasledne: PCMCIA: socket cf6a6834: *** DANGER *** unable to remove socket power

nasiel som us riesenie problemu na [url]http://www.abclinuxu.cz/hardware/show/87232[/url]

potrebujem len poradit ako pridam do parametrov jadra reserve=0x0ff00000,0x0ff00fff

poradi niekto?

[iSteve]

Naposled co jsem tuhle hlasku videl, tak jsem mel ohnutej pin v socketu tak, ze se dotykal jinyho:)

[koza]

no moj pripad to nieje, ale bol som to checknut

nicmene.., sposob akym rezervujem tiehodnoty mi je jasny po boote, spustit kernel xx.xx.xx reserve=xxxxxx,xxxxxx

neviem aku velku cas rezervovat, poradte pls..

[CIJOML]

parametrum lilo.conf k jadru pridej append="hodnoty"

[koza]

hodnoty? prave to je premna zahada pri lspci -v

0000:01:0f.0 CardBus bridge: Ricoh Co Ltd RL5c475 (rev 80)
Subsystem: CARRY Computer ENG. CO Ltd: Unknown device 0101
Flags: bus master, medium devsel, latency 168, IRQ 11
Memory at 17f00000 (32-bit, non-prefetchable)
Bus: primary=01, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 18000000-183ff000 (prefetchable)
Memory window 1: 18400000-187ff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
16-bit legacy interface ports at 0001

takze append=0x17f00000,0x???????? ..