Jak zjistim UDMA disku?

Zdravim mam starsi desku i815 ms-6337 a je to zrejme nejaky zmetek, nebot od jejiho zakoupeni ukazuje v WinXP na primary master UDMA4 a na slave UDMA5. Pokud necham zapojeny jeden disk tak je vzdy UDMA4! Aktualizace biosu nepomohla a asi neexistuje zpusob jak to odstranit. Pouzil jsem ide accelerator v XP a master se tvari jako UDMA5. Zkousim Ubuntu a nevim jak zjistit v jakem rezimu disk jede. Bylo to tady nekolikrat reseno, ale nevim cemu verit. Kdyz zadam hdparm -i /dev/hda tak se zobrazi:

josef@ubuntu:~$ sudo hdparm -i /dev/hda

/dev/hda:

 Model=ST3120814A, FwRev=3.AAE, SerialNo=5LS2SH61
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs RotSpdTol>.5% }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
 BuffType=unknown, BuffSize=8192kB, MaxMultSect=16, MultSect=off
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=234441648
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2
 AdvancedPM=no WriteCache=enabled
 Drive conforms to: Unspecified:  ATA/ATAPI-1 ATA/ATAPI-2 ATA/ATAPI-3 ATA/ATAPI-4 ATA/ATAPI-5 ATA/ATAPI-6 ATA/ATAPI-7
 * signifies the current active mode

ale zadny mod neni oznacen *!

Pokud zadam hdparm -I /dev/hda :

josef@ubuntu:~$ sudo hdparm -I /dev/hda

/dev/hda:

ATA device, with non-removable media
        Model Number:       ST3120814A
        Serial Number:      5LS2SH61
        Firmware Revision:  3.AAE
Standards:
        Supported: 7 6 5 4
        Likely used: 7
Configuration:
        Logical         max     current
        cylinders       16383   16383
        heads           16      16
        sectors/track   63      63
        --
        CHS current addressable sectors:   16514064
        LBA    user addressable sectors:  234441648
        LBA48  user addressable sectors:  234441648
        device size with M = 1024*1024:      114473 MBytes
        device size with M = 1000*1000:      120034 MBytes (120 GB)
Capabilities:
        LBA, IORDY(can be disabled)
        Queue depth: 1
        Standby timer values: spec'd by Standard, no device specific minimum
        R/W multiple sector transfer: Max = 16  Current = ?
        Recommended acoustic management value: 208, current value: 0
        DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
             Cycle time: min=120ns recommended=120ns
        PIO: pio0 pio1 pio2 pio3 pio4
             Cycle time: no flow control=240ns  IORDY flow control=120ns
Commands/features:
        Enabled Supported:
           *    READ BUFFER cmd
           *    WRITE BUFFER cmd
           *    Host Protected Area feature set
           *    Look-ahead
           *    Write cache
           *    Power Management feature set
                Security Mode feature set
           *    SMART feature set
           *    FLUSH CACHE EXT command
           *    Mandatory FLUSH CACHE command
           *    Device Configuration Overlay feature set
           *    48-bit Address feature set
                SET MAX security extension
           *    DOWNLOAD MICROCODE cmd
           *    General Purpose Logging feature set
           *    SMART self-test
           *    SMART error logging
Security:
        Master password revision code = 65534
                supported
        not     enabled
        not     locked
        not     frozen
        not     expired: security count
        not     supported: enhanced erase
HW reset results:
        CBLID- above Vih
        Device num = 0 determined by the jumper
Checksum: correct

Nevim tedy co vlastne plati. Poradi nekdo jeste nejaky zpusob jak to otestovat?

Dotaz: Jak zjistim UDMA disku?

Odpovědi