PCMCIA USB2 nechodi s kernelem 2.6.17

no a jakou mas distribuci, To jadro jsi instalovl jak. Co vypise prikaz dmesg po pripojeni te pcmcia

Linux je jako mušketýři "jeden za všechny, všichni za jednoho"

10.9.2006 12:41 anon123 | skóre: 35 | blog: ganomi
Rozbalit Rozbalit vše Re: PCMCIA USB2 nechodi s kernelem 2.6.17

Debian Unstable s jadrem 2.6.17-2

Vypis dmesg

Linux version 2.6.17-2-686 (Debian 2.6.17-8) (waldi@debian.org) (gcc version 4.1.2 20060814 (prerelease) (Debian 4.1.1-11)) #1 SMP Thu Aug 31 12:53:18 UTC 2006
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
 BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
 BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131056
  DMA zone: 4096 pages, LIFO batch:0
  Normal zone: 126960 pages, LIFO batch:31
DMI 2.2 present.
ACPI: RSDP (v000 CRETE                                 ) @ 0x000f6bd0
ACPI: RSDT (v001 CRETE  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 CRETE  AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: DSDT (v001 CRETE  AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 30000000 (gap: 20000000:dfff0000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro vga=0x317
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (0140a000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 897.734 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 512276k/524224k available (1482k kernel code, 11384k reserved, 544k data, 196k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 1796.84 BogoMIPS (lpj=3593698)
Security Framework v1.0.0 initialized
SELinux:  Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 16k freed
ACPI: setting ELCR to 0200 (from 0800)
CPU0: Intel Pentium III (Coppermine) stepping 0a
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
migration_cost=0
checking if image is initramfs... it is
Freeing initrd memory: 4303k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfafe0, last bus=1
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
PCI quirk: region 4000-403f claimed by PIIX4 ACPI
PCI quirk: region 5000-500f claimed by PIIX4 SMB
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC0] (gpe 9) interrupt mode.
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
pnp: 00:09: ioport range 0xc00-0xc1f has been reserved
PCI: Bridge: 0000:00:01.0
  IO window: d000-dfff
  MEM window: d8000000-d9ffffff
  PREFETCH window: d4000000-d7ffffff
PCI: Bus 2, cardbus bridge: 0000:00:0c.0
  IO window: 00001000-000010ff
  IO window: 00001400-000014ff
  PREFETCH window: 30000000-31ffffff
  MEM window: 32000000-33ffffff
PCI: Bus 6, cardbus bridge: 0000:00:0c.1
  IO window: 00001800-000018ff
  IO window: 00001c00-00001cff
  PREFETCH window: 34000000-35ffffff
  MEM window: 36000000-37ffffff
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:0c.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
* Found PM-Timer Bug on this chipset. Due to workarounds for a bug,
* this time source is slow.  Consider trying other time sources (clock=)
audit: initializing netlink socket (disabled)
audit(1157920037.372:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Limiting direct PCI/PCI transfers.
vesafb: framebuffer at 0xd4000000, mapped to 0xd0880000, using 3072k, total 16384k
vesafb: mode is 1024x768x16, linelength=2048, pages=9
vesafb: protected mode interface info at c000:6185
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI No-Shortcut mode
ACPI wakeup devices:
USB0
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: Fan [FAN] (on)
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Thermal Zone [THRM] (22 C)
8139too Fast Ethernet driver 0.9.27
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:09.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
eth0: RealTek RTL8139 at 0xe400, 00:20:e0:c1:94:26, IRQ 11
eth0:  Identified 8139 chip type 'RTL-8100B/8139D'
8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000e000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hda: FUJITSU MHS2040AT, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: CD-W28E, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 128KiB
hda: 78140160 sectors (40007 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hda: cache flushes supported
 hda: hda1 hda2 hda3
hdc: ATAPI 24X CD-ROM CD-R/RW drive, 1280kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Attempting manual resume
ReiserFS: hda1: found reiserfs format "3.6" with standard journal
ReiserFS: hda1: using ordered data mode
ReiserFS: hda1: journal params: device hda1, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: hda1: checking transaction log (hda1)
ReiserFS: hda1: Using r5 hash to sort names
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
input: PC Speaker as /class/input/input1
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xd0000000
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:00:0c.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0c.0 [3412:7856]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0c.0, mfunc 0x00002001, devctl 0x64
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE,EPP]
input: PS/2 Generic Mouse as /class/input/input2
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000020
ACPI: PCI Interrupt 0000:00:0c.1[B] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
Yenta: CardBus bridge found at 0000:00:0c.1 [3412:7856]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0c.1, mfunc 0x00002001, devctl 0x64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Yenta: ISA IRQ mask 0x0438, PCI irq 11
Socket status: 30000006
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKB] -> GSI 11 (level, low) -> IRQ 11
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
pccard: CardBus card inserted into slot 0
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207
cs: IO port probe 0x3e0-0x4ff: excluding 0x400-0x407 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: IO port probe 0x100-0x3af: excluding 0x200-0x207
cs: IO port probe 0x3e0-0x4ff: excluding 0x400-0x407 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Adding 489972k swap on /dev/hda2.  Priority:-1 extents:1 across:489972k
device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: memory probe 0xa0000000-0xa0ffffff: excluding 0xa0000000-0xa0ffffff
cs: memory probe 0x60000000-0x60ffffff: excluding 0x60000000-0x60ffffff
cs: warning: no high memory space available!
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver

10.9.2006 12:47 kozzi | skóre: 55 | blog: vse_o_vsem | Pacman (Bratrušov)
Rozbalit Rozbalit vše Re: PCMCIA USB2 nechodi s kernelem 2.6.17

pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.

toto myslim mluvi za vse

pouzivas pcmciautils nebo pouzivas pcmcia-cs ci tak nejak

Linux je jako mušketýři "jeden za všechny, všichni za jednoho"

10.9.2006 16:00 anon123 | skóre: 35 | blog: ganomi
Rozbalit Rozbalit vše Re: PCMCIA USB2 nechodi s kernelem 2.6.17

Pouzivam pcmciautils. Na tom linku jsem zacal. Nemohl jsem tam nic najit co by mi pomohlo.

Dotaz: PCMCIA USB2 nechodi s kernelem 2.6.17

Odpovědi