Portál AbcLinuxu, 11. května 2025 07:05
usb 2-1: new full speed USB device using uhci_hcd and address 7 input: USB Audio//class/input as input11 input: USB HID v1.00 Device [USB Audio] on usb-0000:00:1d.0-1---) kdyz dam "modprobe snd-usb-audio" a pak "asoundconf list", objevi se tam headset:
asoundconf list Names of available sound cards: Intel (moje zvukovka) Audio (headset)1) Zajimalo by me, jestli, kdyz se to jevi jako samostatna zvukovka, jestli potrebuju mit zapnutou i tu svoji integrovanou zvukarnu, aby to jelo (nebudu loadovat snd-hda-intel ale jenom ten svuj headset) 2) Taky me zarazi, ze je tam jenom Audio a ne nejaky blizsi nazev nebo tak... ---) v lsusb vidim:
Bus 002 Device 008: ID 0d8c:0006 C-Media Electronics, Inc.3) Muzu proste NEmit naloadovany driver pro zvukovku a slyset zvuk pres alsu na tom headsetu??? 5) jo a taky by me zajimalo, jestli existuje nejaka redukce ci konvertor USB<--->jack , protoze jsem videl u nejakych sluchatek na netu neco takoveho, ale mozna je to specificke pro kazdy produkt...... Ma s tim prosim nekdo nejake zkusenosti?? Uz se s tim rypu 2.den :( Ach jo, proc je ten zvuk v linuxu tak blbe udelanej...
aplay -l
**** List of PLAYBACK Hardware Devices **** card 0: Intel [HDA Intel], device 0: ALC260 Analog [ALC260 Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 1: Audio [USB Audio], device 0: USB Audio [USB Audio] Subdevices: 1/1 Subdevice #0: subdevice #0
aplay -D plughw:1 Monty-Python.wav aplay: main:550: audio open error: Device or resource busy:(((((((((((((
modprobe snd-usb-audio
a ted to pise
play -D plughw:1 Monty-Python.wav
Playing WAVE 'Monty-Python.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono aplay: xrun:1093: read/write error, state = PREPAREDa kdyz dam
aplay -v -D plughw:1 Monty-Python.wav
Playing WAVE 'Monty-Python.wav' : Unsigned 8 bit, Rate 8000 Hz, Mono
Plug PCM: Rate conversion PCM (48000, sformat=U8)
Its setup is:
stream : PLAYBACK
access : RW_INTERLEAVED
format : U8
subformat : STD
channels : 1
rate : 8000
exact rate : 8000 (8000/1)
msbits : 8
buffer_size : 4000
period_size : 1000
period_time : 125000
tick_time : 4000
tstamp_mode : NONE
period_step : 1
sleep_min : 0
avail_min : 1000
xfer_align : 1000
start_threshold : 4000
stop_threshold : 4000
silence_threshold: 0
silence_size : 0
boundary : 262144000
Slave: Route conversion PCM (sformat=S16_LE)
Transformation table:
0 <- 0
1 <- 0
2 <- 0
3 <- 0
4 <- 0
5 <- 0
6 <- 0
7 <- 0
Its setup is:
stream : PLAYBACK
access : MMAP_INTERLEAVED
format : U8
subformat : STD
channels : 1
rate : 48000
exact rate : 48000 (48000/1)
msbits : 8
buffer_size : 24006
period_size : 6000
period_time : 125000
tick_time : 4000
tstamp_mode : NONE
period_step : 1
sleep_min : 0
avail_min : 6000
xfer_align : 6000
start_threshold : 24000
stop_threshold : 24006
silence_threshold: 0
silence_size : 0
boundary : 1573257216
Slave: Hardware PCM card 1 'USB Audio' device 0 subdevice 0
Its setup is:
stream : PLAYBACK
access : MMAP_INTERLEAVED
format : S16_LE
subformat : STD
channels : 8
rate : 48000
exact rate : 48000 (48000/1)
msbits : 16
buffer_size : 24006
period_size : 6000
period_time : 125000
tick_time : 4000
tstamp_mode : NONE
period_step : 1
sleep_min : 0
avail_min : 6000
xfer_align : 6000
start_threshold : 24000
stop_threshold : 24006
silence_threshold: 0
silence_size : 0
boundary : 1573257216
Status(R/W):
state : PREPARED
trigger_time: 1189436400.466833000
tstamp : 1189436400.467013000
delay : 4000
avail : 0
avail_max : 0
aplay: xrun:1093: read/write error, state = PREPARED
:((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((((
cannot submit datapipe for urb 5, err = -28
Advanced Linux Sound Architecture Driver Version 1.0.10rc1 (Mon Sep 12 08:13:09 2005 UTC).ja sem asi debil :) ale dik zatim, ja se s tim poperu :)
aplay: xrun:1093: read/write error, state = PREPAREDa
cannot submit datapipe for urb 5, err = -28:(((((((((((((((((((((((((((((((
Tiskni
Sdílej:
ISSN 1214-1267, (c) 1999-2007 Stickfish s.r.o.