Portál AbcLinuxu, 1. listopadu 2025 10:44
eth1 Scan completed :
Cell 01 - Address: 00:1D:0F:E3:9C:32
ESSID:"Rychnovsky"
Protocol:IEEE 802.11bg
Mode:Master
Channel:11
Encryption key:on
Bit Rates:54 Mb/s
Extra: Rates (Mb/s): 1 2 5.5 9 11 6 12 18 24 36 48 54
Quality=71/100 Signal level=-19 dBm
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
Extra: Last beacon: 124ms ago
iwconfig eth1:
eth1 unassociated ESSID:"Rychnovsky"
Mode:Managed Frequency=2.462 GHz Access Point: Not-Associated
Bit Rate=0 kb/s Tx-Power=20 dBm Sensitivity=8/0
Retry limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
/etc/wpa_supplicant.conf
ctrl_interface=/var/run/wpa_supplicant
network={
ssid="Rychnovsky"
scan_ssid=1
key_mgmt=WPA-PSK
pairwise=CCMP THIP
group=CCMP TKIP
psk="tady je kod, ktery mi dalo wpa_passphrase"
}
Poradte mi nekdo prosim, co je spatne, nebo co je jeste potreba udelat.
Diky Geralt
iwconfig wlan0 key 0123-4567-89 ty čísla jsou ten klíč v hexa (může to být i bez pomlček), detaily jsou v man iwconfig
Pokud ti to nepůjde, tak bych zkusil na routru vypnout WEP i WPA a zkusit se připojit jen na nezabezpečenou wifi a pak postupně zapnout WEP a WPA.
Module Size Used by radeon 116000 1 drm 73236 2 radeon rfcomm 40216 0 l2cap 26372 5 rfcomm bluetooth 50020 4 rfcomm,l2cap ppdev 9220 0 speedstep_centrino 8400 1 cpufreq_userspace 4696 1 cpufreq_stats 5636 0 freq_table 4740 2 speedstep_centrino,cpufreq_stats cpufreq_powersave 1920 0 cpufreq_ondemand 6428 0 cpufreq_conservative 7332 0 video 16260 0 tc1100_wmi 6916 0 sony_acpi 5644 0 pcc_acpi 12416 0 hotkey 11556 0 dev_acpi 11140 0 container 4608 0 button 6672 0 asus_acpi 11540 0 acpi_sbs 19980 0 battery 9988 1 acpi_sbs ac 5252 1 acpi_sbs i2c_acpi_ec 5120 1 acpi_sbs i2c_core 21904 1 i2c_acpi_ec ipv6 266112 6 dm_mod 59192 1 af_packet 22920 2 md_mod 72532 0 sr_mod 16932 0 sbp2 24196 0 scsi_mod 139496 2 sr_mod,sbp2 lp 11844 0 pcmcia 40508 0 joydev 10048 0 tsdev 8000 0 parport_pc 35780 1 parport 36296 3 ppdev,lp,parport_pc yenta_socket 28428 1 rsrc_nonstatic 13440 1 yenta_socket pcmcia_core 42640 3 pcmcia,yenta_socket,rsrc_nonstatic ipw2200 107308 0 ieee80211 37064 1 ipw2200 ieee80211_crypt 6272 1 ieee80211 ieee80211_1_1_13 38216 0 ieee80211_1_1_13_crypt 6784 1 ieee80211_1_1_13 skge 38544 0 sdhci 14848 0 mmc_core 30104 1 sdhci pcspkr 2180 0 rtc 13492 0 usbhid 39904 0 snd_hda_intel 18964 0 snd_hda_codec 157616 1 snd_hda_intel psmouse 36100 0 snd_pcm_oss 53664 0 snd_mixer_oss 18688 1 snd_pcm_oss serio_raw 7300 0 snd_pcm 89864 3 snd_hda_intel,snd_hda_codec,snd_pcm_oss snd_timer 25220 1 snd_pcm snd 55268 6 snd_hda_intel,snd_hda_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer hw_random 5652 0 shpchp 45632 0 soundcore 10208 1 snd pci_hotplug 29236 1 shpchp snd_page_alloc 10632 2 snd_hda_intel,snd_pcm intel_agp 22940 1 agpgart 34888 2 drm,intel_agp evdev 9856 2 ext3 135944 1 jbd 58772 1 ext3 ide_generic 1536 0 ohci1394 35124 0 ieee1394 299832 2 sbp2,ohci1394 ehci_hcd 34184 0 uhci_hcd 33808 0 usbcore 130820 4 usbhid,ehci_hcd,uhci_hcd ide_cd 33028 0 cdrom 38560 2 sr_mod,ide_cd ide_disk 17664 3 piix 11012 1 generic 5124 0 thermal 13576 0 processor 23360 2 speedstep_centrino,thermal fan 4868 0 capability 5000 0 commoncap 7296 1 capability vga16fb 13704 1 vgastate 10368 1 vga16fb fbcon 42784 72 tileblit 2816 1 fbcon font 8320 1 fbcon bitblit 6272 1 fbcon softcursor 2304 1 bitblitten key jsem skutecne nenastavoval, ale bohuzel ani z man iwconfig jsem nepochopil, co to presne ten klic je; to, co mi vygeneroval wpa_passphrase je velmi dlouhe ... Geralt
23.2.2008 17:21
vencour | skóre: 56
| blog: Tady je Vencourovo
| Praha+západní Čechy
Sám mam wpa v pohodě, musel jsem ho rozchodit jen přes zdejší rady, poradnu a tak ... změnili mi kluci profil 
. Takže ... musíte mít wpa_supplicant, upravíte konfigurák, projdete "man wpa_supplicant" a ... uvidíte. Já to dělam přes řádku, tedy spouštim skript, kde je na 1. řádce "wpa_supplicant -dd -c /etc/wpa_supplicant/wpa_supplicant.conf -i ath0 -D wext &" a pak ještě "dhcpcd ath0", v konfiguráku mam:
$ more /etc/wpa_supplicant/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
ap_scan=1
network={
ssid="ESSID_apecka"
key_mgmt=WPA-PSK IEEE8021X NONE
scan_ssid=1
pairwise=CCMP TKIP
group=CCMP TKIP WEP104 WEP40
psk="Fraze_nebo_heslo_jak_kdo_chce"
eap=TTLS PEAP TLS
# identity="user@example.com"
# password="foobar"
}
#network={
# key_mgmt=NONE
# priority=-9999999
#}
K tomu, mam dojem, že musí být v kernelu přidělaná podpora pro kryptování, znam kluky, kterým tohle nestačí a právě "cryptographic API" snad by tam mělo pomoct? Když tak pomůže nějakej "debug" ... viděl jsem logy, kde to právě něco o tomhle psalo.
network={
ssid="Rychnovsky"
key_mgmt=WPA-PSK
scan_ssid=1
psk=816551ef41d8d27a131cc168bff4b939dfc9198adebfda664b125b77cb3a096d
}
a kdyz jej spustim wpa_supplicant -ieth1 -c/etc/wpa_supplicant.conf -d, tak mi to vypise:
Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'default' ctrl_interface 'N/A'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Priority group 0
id=0 ssid='Rychnovsky'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
SIOCGIWRANGE: WE(compiled)=19 WE(source)=18 enc_capa=0xf
capabilities: key_mgmt 0xf enc 0xf
Own MAC address: 00:15:00:31:8d:d6
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Added interface eth1
Wireless event: cmd=0x8b06 len=8
State: DISCONNECTED -> SCANNING
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=10):
52 79 63 68 6e 6f 76 73 6b 79 Rychnovsky
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to initiate AP scan.
Setting scan request: 10 sec 0 usec
Scan timeout - try to get results
Received 226 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:1d:0f:e3:9c:32 ssid='Rychnovsky' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:1d:0f:e3:9c:32 (SSID='Rychnovsky' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
State: ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
State: DISCONNECTED -> SCANNING
Starting AP scan (broadcast SSID)
Scan timeout - try to get results
Received 224 bytes of scan results (1 BSSes)
Scan results: 1
Selecting BSS from priority group 0
0: 00:1d:0f:e3:9c:32 ssid='Rychnovsky' wpa_ie_len=24 rsn_ie_len=0 caps=0x11
selected based on WPA IE
Trying to associate with 00:1d:0f:e3:9c:32 (SSID='Rychnovsky' freq=0 MHz)
Cancelling scan request
WPA: clearing own WPA/RSN IE
Automatic auth_alg selection: 0x1
WPA: using IEEE 802.11i/D3.0
WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2
WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
WPA: clearing AP RSN IE
WPA: using GTK TKIP
WPA: using PTK TKIP
WPA: using KEY_MGMT WPA-PSK
WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02
No keys have been configured - skip key clearing
wpa_driver_hostap_set_drop_unencrypted: enabled=1
State: SCANNING -> ASSOCIATING
wpa_driver_hostap_associate
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Setting authentication timeout: 10 sec 0 usec
EAPOL: External notification - EAP success=0
EAPOL: External notification - EAP fail=0
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
Wireless event: cmd=0x8b06 len=8
Wireless event: cmd=0x8b1a len=19
CTRL-EVENT-TERMINATING - signal 2 received
Removing interface eth1
State: ASSOCIATING -> DISCONNECTED
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_hostap_set_wpa: enabled=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
wpa_driver_hostap_set_drop_unencrypted: enabled=0
wpa_driver_hostap_set_countermeasures: enabled=0
No keys have been configured - skip key clearing
Removed BSSID 00:00:00:00:00:00 from blacklist (clear)
Cancelling scan request
, ale internet bohuzel nenaskoci ...
23.2.2008 17:46
vencour | skóre: 56
| blog: Tady je Vencourovo
| Praha+západní Čechy
Ok, především by mělo být výstupem správné funkčnosti wpa_supplicantu to, že vidíte linkovou vrstvu, tedy u "ip addr", že nemáte "no link detect" nebo "no-carrier". Že jsem tak smělej, co máte v tom kernelu za kryptování, algoritmy zapnuté? Budu to samé radit mému okolí ... tuto cestu zkontrolovat, jinak zatím nevím ... ať jsem konkrétní, já tam mam ... (nejsem si jistý, co je přesně potřeba)
$ grep CRYPT .config | grep =[ym] CONFIG_SUSPEND2_CRYPTO=y CONFIG_IEEE80211_CRYPT_WEP=y CONFIG_IEEE80211_CRYPT_CCMP=y CONFIG_IEEE80211_CRYPT_TKIP=y CONFIG_BLK_DEV_CRYPTOLOOP=m CONFIG_CRYPTO=y CONFIG_CRYPTO_ALGAPI=y CONFIG_CRYPTO_BLKCIPHER=y CONFIG_CRYPTO_HASH=y CONFIG_CRYPTO_MANAGER=y CONFIG_CRYPTO_HMAC=y CONFIG_CRYPTO_NULL=y CONFIG_CRYPTO_MD4=y CONFIG_CRYPTO_MD5=y CONFIG_CRYPTO_SHA1=y CONFIG_CRYPTO_SHA256=y CONFIG_CRYPTO_SHA512=y CONFIG_CRYPTO_WP512=y CONFIG_CRYPTO_TGR192=y CONFIG_CRYPTO_ECB=y CONFIG_CRYPTO_CBC=m CONFIG_CRYPTO_PCBC=m CONFIG_CRYPTO_DES=y CONFIG_CRYPTO_FCRYPT=y CONFIG_CRYPTO_BLOWFISH=y CONFIG_CRYPTO_TWOFISH=y CONFIG_CRYPTO_TWOFISH_COMMON=y CONFIG_CRYPTO_SERPENT=y CONFIG_CRYPTO_AES=y CONFIG_CRYPTO_AES_586=y CONFIG_CRYPTO_CAST5=y CONFIG_CRYPTO_CAST6=y CONFIG_CRYPTO_TEA=y CONFIG_CRYPTO_ARC4=y CONFIG_CRYPTO_KHAZAD=y CONFIG_CRYPTO_ANUBIS=y CONFIG_CRYPTO_DEFLATE=y CONFIG_CRYPTO_LZF=y CONFIG_CRYPTO_MICHAEL_MIC=y CONFIG_CRYPTO_CRC32C=y CONFIG_CRYPTO_CAMELLIA=y CONFIG_CRYPTO_TEST=m CONFIG_CRYPTO_DEV_PADLOCK=m CONFIG_CRYPTO_DEV_PADLOCK_AES=m CONFIG_CRYPTO_DEV_PADLOCK_SHA=m CONFIG_CRYPTO_DEV_GEODE=mP.S. fakt tam máte hostap? Nikdy jsem ho nemusel použít, slyšel jsem na něj spíš slova o problémech.
Tiskni
Sdílej:
ISSN 1214-1267, (c) 1999-2007 Stickfish s.r.o.