Portál AbcLinuxu, 5. května 2025 16:43
Nov 30 07:43:12 Mint2 kernel: [ 313.874424] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Nov 30 07:43:12 Mint2 kernel: [ 313.874431] ata1.00: irq_stat 0x40000001
Nov 30 07:43:12 Mint2 kernel: [ 313.874437] ata1.00: failed command: READ DMA EXT
Nov 30 07:43:12 Mint2 kernel: [ 313.874448] ata1.00: cmd 25/00:08:c8:25:41/00:00:15:00:00/e0 tag 11 dma 4096 in
Nov 30 07:43:12 Mint2 kernel: [ 313.874448] res 51/40:08:c8:25:41/00:00:15:00:00/e0 Emask 0x9 (media error)
Nov 30 07:43:12 Mint2 kernel: [ 313.874453] ata1.00: status: { DRDY ERR }
Nov 30 07:43:12 Mint2 kernel: [ 313.874457] ata1.00: error: { UNC }
Nov 30 07:43:12 Mint2 kernel: [ 313.874753] ata1.00: configured for UDMA/133
Nov 30 07:43:12 Mint2 kernel: [ 313.874782] ata1: EH complete
Nov 30 07:43:12 Mint2 kernel: [ 313.910393] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x0
Nov 30 07:43:12 Mint2 kernel: [ 313.910403] ata1.00: irq_stat 0x40000001
Nov 30 07:43:12 Mint2 kernel: [ 313.910411] ata1.00: failed command: READ DMA EXT
Nov 30 07:43:12 Mint2 kernel: [ 313.910428] ata1.00: cmd 25/00:08:c8:25:41/00:00:15:00:00/e0 tag 9 dma 4096 in
Nov 30 07:43:12 Mint2 kernel: [ 313.910428] res 51/40:08:c8:25:41/00:00:15:00:00/e0 Emask 0x9 (media error)
Nov 30 07:43:12 Mint2 kernel: [ 313.910435] ata1.00: status: { DRDY ERR }
Nov 30 07:43:12 Mint2 kernel: [ 313.910440] ata1.00: error: { UNC }
Nov 30 07:43:12 Mint2 kernel: [ 313.910838] ata1.00: configured for UDMA/133
Nov 30 07:43:12 Mint2 kernel: [ 313.910879] ata1: EH complete
......... a podobně toho je klidně 500 mega textu
Ten výpis se objeví v syslog, výpis na obrazovce se po chvíli zastaví. Popravdě netuším co to znamená, neporadil by někdo?
Nov 30 07:43:12 Mint2 kernel: [ 313.910411] ata1.00: failed command: READ DMA EXT
Nov 30 07:43:12 Mint2 kernel: [ 313.910428] ata1.00: cmd 25/00:08:c8:25:41/00:00:15:00:00/e0 tag 9 dma 4096 in
Nov 30 07:43:12 Mint2 kernel: [ 313.910428] res 51/40:08:c8:25:41/00:00:15:00:00/e0 Emask 0x9 (media error)
Nov 30 07:43:12 Mint2 kernel: [ 313.910435] ata1.00: status: { DRDY ERR }
Nov 30 07:43:12 Mint2 kernel: [ 313.910440] ata1.00: error: { UNC }
Disk nevie čítať zo zdieľanej pamäte (failed command read dma), UNC znamená uncorrectable teda neopraviteľná chyba. Buď je to zle zasunutý kábel, alebo zoxidované koncovky, alebo nestíha zdroj, alebo už ten disk umiera.
Ktorý disk to je sa dá zistiť o syslogu keď sa pri štarte systému identifikujú disky. Je značený ako ata1.0, a pri štarte bude vypísaný výrobca, typ a kapacita.
Pán Fiedler, nechcete ten disk predsa len vyhodiť ako bolo už pár krát taktne naznačované?
.
30.11.2018 21:20
Petr Fiedler | skóre: 35
| blog: Poradna
| Brno
Pán Fiedler, nechcete ten disk predsa len vyhodiť ako bolo už pár krát taktne naznačované?
Bouchl ses do hlavy?
sudo apt install lsscsi lsscsi -v
30.11.2018 14:39
dmesg | grep ata1.00 | grep ATA
smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.15.0-39-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: ADATA SU700
Serial Number: 2H2320062333
LU WWN Device Id: 5 707c18 10050c4d5
Firmware Version: B170428a
User Capacity: 240,057,409,536 bytes [240 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: Solid State Device
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-2 (minor revision not indicated)
SATA Version is: SATA 3.2, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Fri Nov 30 20:49:21 2018 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 33) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 1) minutes.
Conveyance self-test routine
recommended polling time: ( 1) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 0
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
9 Power_On_Hours 0x0012 100 100 000 Old_age Always - 763
12 Power_Cycle_Count 0x0012 100 100 000 Old_age Always - 242
167 Unknown_Attribute 0x0022 100 100 000 Old_age Always - 0
168 Unknown_Attribute 0x0012 100 100 000 Old_age Always - 4
169 Unknown_Attribute 0x0013 093 093 010 Pre-fail Always - 257701970367
173 Unknown_Attribute 0x0012 200 200 000 Old_age Always - 30066540559
175 Program_Fail_Count_Chip 0x0013 040 100 010 Pre-fail Always - 0
180 Unused_Rsvd_Blk_Cnt_Tot 0x0033 093 093 020 Pre-fail Always - 852
192 Power-Off_Retract_Count 0x0012 100 100 000 Old_age Always - 31
194 Temperature_Celsius 0x0022 066 066 030 Old_age Always - 34 (Min/Max 33/40)
231 Temperature_Celsius 0x0033 094 094 005 Pre-fail Always - 1536
233 Media_Wearout_Indicator 0x0032 100 100 000 Old_age Always - 3387088512
234 Unknown_Attribute 0x0032 100 100 000 Old_age Always - 1606804930560
241 Total_LBAs_Written 0x0032 100 100 000 Old_age Always - 2724954965
242 Total_LBAs_Read 0x0032 100 100 000 Old_age Always - 3829255297
SMART Error Log Version: 1
ATA Error Count: 10 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 10 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:42:32.800 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:42:27.500 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:42:27.500 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:42:27.500 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:42:27.500 SET FEATURES [Enable SATA feature]
Error 9 occurred at disk power-on lifetime: 760 hours (31 days + 16 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:41:49.300 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:41:43.900 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:41:43.900 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:41:43.900 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:41:43.900 SET FEATURES [Enable SATA feature]
Error 8 occurred at disk power-on lifetime: 759 hours (31 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 00 00 00 a0
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
ec 00 00 00 00 00 a0 08 00:04:34.500 IDENTIFY DEVICE
ef 10 02 00 00 00 a0 08 00:04:29.200 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:04:29.200 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:04:29.200 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:04:29.200 SET FEATURES [Enable SATA feature]
Error 7 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 80 f9 a0 e1 Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 f9 a0 e1 08 00:05:28.500 READ DMA
ca 00 28 18 df a1 e1 08 00:05:28.500 WRITE DMA
ef 10 02 00 00 00 a0 08 00:05:28.500 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:05:28.500 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:28.500 SET FEATURES [Set transfer mode]
Error 6 occurred at disk power-on lifetime: 757 hours (31 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 80 f9 a0 e1 Error: UNC 8 sectors at LBA = 0x01a0f980 = 27326848
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 80 f9 a0 e1 08 00:05:28.500 READ DMA
ef 10 02 00 00 00 a0 08 00:05:28.500 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 a0 08 00:05:28.500 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 00:05:28.500 SET FEATURES [Set transfer mode]
ef 10 02 00 00 00 a0 08 00:05:28.500 SET FEATURES [Enable SATA feature]
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 763 -
# 2 Extended offline Completed without error 00% 763 -
# 3 Extended offline Completed without error 00% 760 -
# 4 Short offline Completed without error 00% 759 -
# 5 Short offline Completed without error 00% 754 -
# 6 Short offline Completed without error 00% 412 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
1.12.2018 08:59
Petr Fiedler | skóre: 35
| blog: Poradna
| Brno
No právě, já asi aktualizoval posledně jak jsem to bez čtení odklepnul i jádro a při startu mě to nedává na výběr. Nevím jak to změnit na starší.
Nainstaluj si Grub Customizer:
sudo su apt-add-repository danielrichter2007/grub-customizer apt update apt install grub-customizer
V Grub Customizeru si můžeš krom jiného nastavit, na jak dlouho se ti má při startu pc zobrazovat nabídka GRUBu. V ní pak vyber "Advenced options for Linux Mint" a tam můžeš vybrat starší jádro.
Pokud bys nechtěl instalovat, tak při rebootu (tuším) stačí držet Shift a pak by taky mělo jít vybrat starší jádro.
Oboje situaci ale moc neřeší. Je to spíše na odzkoušení, jestli to je opravdu tím jádrem. Musel bys to dělat při každém startu pc.
Na správu jader si můžeš nainstalovat UKUU. Když pak v této utilitě odinstaluješ poslední jádro (zbrklý upgrade), tak se při dalším startu pc použije to poslední funkční jádro. UKUU nainstaluješ takhle:
apt-add-repository -y teejee2008/ppa apt update apt install ukuu
1.12.2018 10:30
Petr Fiedler | skóre: 35
| blog: Poradna
| Brno
1.12.2018 10:25
Petr Fiedler | skóre: 35
| blog: Poradna
| Brno
Pokud se jedná o jádra, která se ti sami nabízejí k upgradu, tak stačí kliknout na panelu na ikonu správce aktualizací > zobrati > linuxová jádra a tam to taky jde odinstalovat. To jsem si před tím neuvědomil. Každopádně v UKUU si můžeš zkusit nainstalovat nejnovější jádro - 4.19.5. Mě na LM 18.3 funguje perfektně. Pokud se do toho pustíš, tak ti doporučuji NEinstalovat rc jádra. Jedná se o kandidáty na vydání. Rc by šlo použít, kdybys měl naprosto nový HW. A taky si v tom správci aktualizací odinstaluj starší jádra než 4.15.0.38. Pokud ti to poslední jádro delší dobu šlape perfektně, tak jsou v systému zbytečná. Nainstalovat se když tak dají kdykoliv.
1.12.2018 11:00
Petr Fiedler | skóre: 35
| blog: Poradna
| Brno
.
1.12.2018 11:57
Petr Fiedler | skóre: 35
| blog: Poradna
| Brno
No možná neprojevil, ale na to ses neptal. Ptal ses, jestli to má cenu rovnou na Mint 19? Takže jsem ti odpovídal na to.
Tiskni
Sdílej:
ISSN 1214-1267, (c) 1999-2007 Stickfish s.r.o.