compact flash na IDE - problem s kernelem

Zdravim,
pri bootu mi u Compact Flash zarizeni pripojeneho na IDE pise kernel 2x nasledujici hlasku (cely vypis kernelu tykajici se IDE kdyztak pridavam na konec postu):

hda: set_drive_speed_status: status=0x51 { DriveReady
 SeekComplete Error }
hda: set_drive_speed_status: error=0x04
 { DriveStatusError }
ide0: Drive 0 didn't accept speed setting. Oh, well.

Zarizeni pak dale funguje zda se bez problemu (tj. jde cist a zapisovat), ale jelikoz se pak stavaji bizarni zalezitosti s harddiskem ... nejdrive z namountovane partition jakoby zacnou mizet soubory (ls je prestava zobrazovat) az po spoustu podobnych hlasek kernelu i k harddisku a naproste nemoznosti s harddiskem pracovat dokud nepripojim jeste CDROM a nenabootuju z ni, kdy pak zacne ten harddisk chodit uplne normalne i bez CD?! ... tak to mozna zase tak bez problemu neni :(

Kazdopadne se mi za boha nepodarilo tuhle hlasku eliminovat zadnym z nasledujich zpusobu:
- ruznym pouzitym HW a to jak CF (klasicka CF + CFIDE redukce, IDE Flash drive) tak zbytku (desky s cipsety KM266 a KT400)
- ruznymi pouzitymi jadry (2.4.21 az 2.4.24) s ruznym nastavenim (zapnuti VIA chipset supportu, Generic PCI IDE, DMA by default atd.). Pouze stare jadro 2.2.neco zadnou hlasku nepise.

Nesetkali jste se nekdo s timto a nevite co s tim ? Pripadne melo by smysl zkouset jiny IDE cipset (SiS, nForce, ...) neni to treba nejaky bug ve VIA cipsetech ?

Diky za info.

Charon

-------------------------------------------------
Uniform Multi-Platform E-IDE driver Revision:
 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes;
 override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:11.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
    ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio,
 hdb:pio
    ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA,
 hdd:DMA
hda: 64MB CHH, ATA DISK drive
hda: set_drive_speed_status: status=0x51 { DriveReady
 SeekComplete Error }
hda: set_drive_speed_status: error=0x04
 { DriveStatusError }
ide0: Drive 0 didn't accept speed setting. Oh, well.
hdc: ST320011A, ATA DISK drive
hdd: SAMSUNG CD-ROM SC-152L, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: task_no_data_intr: status=0x51 { DriveReady
 SeekComplete Error }
hda: task_no_data_intr: error=0x04 { DriveStatusError }
hda: 125184 sectors (64 MB) w/1KiB Cache, CHS=978/4/32
hdc: attached ide-disk driver.
hdc: host protected area => 1
hdc: 39102336 sectors (20020 MB) w/2048KiB Cache, CHS=38792/16/63
ide-cd: passing drive hdd to ide-scsi emulation.
hdd: attached ide-scsi driver.
Partition check:
 hda: unknown partition table
 hdc: [PTBL] [2434/255/63] hdc1
ide: late registration of driver.
--------------------------------------------------

Dotaz: compact flash na IDE - problem s kernelem

Odpovědi