Dotaz: Nedokonale vypnutie PC

[Milec]

Zravicko, pri pouziti standartneho prikazu na vypnutie pc

shutdown -h now

mam zaujmavy problem. A to, ze sa pc nevypne uplne, ale cooler na procesore stale zostava bezat. Spravi to az podrzanie power off buttonu. Any ideas?

Odpovědi

[Yeti]

Zkusit změnit CONFIG_APM_REAL_MODE_POWER_OFF v konfiguraci jádra na opačnou hodnotu, než je teď.

[Petr Šobáň]

Taky zaleží zda používáte APM nebo ACPI, mě na mé desce ACPI taky nefunguje jak by mělo, APM OK.

[Yeti]

Jo, pokud používá ACPI, tak moje rada neudělá nic. Chce to více informací...

[Zdenek Sl.]

Jo s ACPI jsem si uzil svoje Presne tohle mi delal Linux na Notebooku. Zamerne rikam Linux,protoze krome Suse to nezvladnulo defaultne zadne distro.

Navic pokud jsem pouze pridal acpi=on do Lila,tak jsem spolehlive zamrznul pri bootu.Pak jsem narazil v jadernych novinach na zminku o potizich ACPI s APIC,ktere je nutno vyhodit z jadra ! vypnuti v LILO nepomahalo!

Hodne stesti PS: Nic proti Suse,ale je strasne nenazrane na misto,kvuli desnym zavislostem

[Milec]

Pardon. Pouzivam acpi.

[Libor Klepac]

take pouzivam acpi, a s nekterymi jadry to dela (muze to mozna take byt kvuli nvidia modulu), zalezi to kus od kusu, ted mam 2.6.6-rc2-mm2 a je to ok

mam novou desku a (epox 4pla) a dela to tohle + obcas to zamrzne pri startu (podezrival jsem nvidia+smp, ale vzhledem ze to mrzne i pred zavedenim moulu....), kdyz jsem ukazoval lidem "linux" na lanparty ,tak i pri chodu

jinak kousky dmesg

DMI 2.2 present.
ACPI: RSDP (v000 IntelR                                    ) @ 0x000f7070
ACPI: RSDT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000
ACPI: FADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040
ACPI: MADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff72c0
ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:2 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:2 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
....
....
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 *10 11 12 14 15)
.....
.....
ACPI: Power Button (FF) [PWRF]
ACPI: Fan [FAN] (on)
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Thermal Zone [THRM] (29 C)

libor

[Libor Klepac]

ehm.....modulu samozrejme, ne moulu , blbne mi d na klavesnici

libor