Portál AbcLinuxu, 6. května 2025 06:38
16.6.2006 20:53
vencour | skóre: 56
| blog: Tady je Vencourovo
| Praha+západní Čechy
Tak experimentovat s typem ... měnit card nebo tuner?
27.1.2007 21:43
Martin Stiborský | skóre: 26
| blog: Stibiho bláboly
| Opava
options bttv card=42 tuner=5 radio=1v /etc/modprobe.conf
options bttv card=42 tuner=8 radio=1
Jelikož obraz šel, měl jsem zato, že je to v pořádku..
Ještě jednou dík moc!
27.1.2007 21:52
Martin Stiborský | skóre: 26
| blog: Stibiho bláboly
| Opava
27.1.2007 22:16
Martin Stiborský | skóre: 26
| blog: Stibiho bláboly
| Opava
bttv0: Bt878 (rev 17) at 0000:01:0a.0, irq: 20, latency: 32, mmio: 0xd4000000 bttv0: using: ProVideo PV951 [card=42,insmod option] bttv0: gpio: en=00000000, out=00000000 in=00ffffff [init] bttv0: using tuner=5 bttv0: i2c: checking for TDA9875 @ 0xb0... found tda9875: no such chip at 0xb0 (dic=0x11 rev=0x2) bttv0: i2c: checking for TDA7432 @ 0x8a... not found tvaudio 0-0058: found tda9874a. tvaudio 0-0058: tda9874h/a found @ 0xb0 (bt878 #0 [sw]) tvaudio 0-004b: pic16c54 (PV951) found @ 0x96 (bt878 #0 [sw]) bttv0: i2c: checking for TDA9887 @ 0x86... not found tuner 0-0060: All bytes are equal. It is not a TEA5767 tuner 0-0060: chip found @ 0xc0 (bt878 #0 [sw]) tuner 0-0060: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) bttv0: registered device video0 bttv0: registered device vbi0 bttv0: registered device radio0 bttv0: PLL: 28636363 => 35468950 .. ok bt878: AUDIO driver version 0.0.0 loaded bt878: Bt878 AUDIO function found (0). ACPI: PCI Interrupt 0000:01:0a.1[A] -> Link [APC3] -> GSI 18 (level, high) -> IRQ 20 bt878_probe: card id=[0x0],[ < N U L L > ] has DVB functions. bt878(0): Bt878 (rev 17) at 01:0a.1, irq: 20, latency: 32, memory: 0xd4001000 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected NVIDIA nForce2 chipset agpgart: AGP aperture is 64M @ 0xd0000000 cpufreq: Detected nForce2 chipset revision A2 cpufreq: FSB changing is maybe unstable and can lead to crashes and data loss. cpufreq: FSB currently at 165 MHz, FID 11.5 device-mapper: 4.6.0-ioctl (2006-02-17) initialised: dm-devel@redhat.com EXT3 FS on hda5, internal journal Adding 1124508k swap on /dev/hda6. Priority:-1 extents:1 across:1124508k kjournald starting. Commit interval 5 seconds EXT3 FS on hda9, internal journal EXT3-fs: mounted filesystem with ordered data mode. NTFS driver 2.1.27 [Flags: R/O DEBUG MODULE]. NTFS volume version 3.1. kjournald starting. Commit interval 5 seconds EXT3 FS on hda7, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on hda8, internal journal EXT3-fs: mounted filesystem with ordered data mode. loop: loaded (max 8 devices, max 1 partitions per device) hdd: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(66) Uniform CD-ROM driver Revision: 3.20 Netfilter messages via NETLINK v0.30. ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ip_conntrack version 2.4 (8191 buckets, 65528 max) - 224 bytes per conntrack ACPI: Fan [FAN] (on) Using specific hotkey driver Removing netfilter NETLINK layer. ACPI: Thermal Zone [THRM] (52 C) ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 22 ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 22 (level, high) -> IRQ 16 PCI: Setting latency timer of device 0000:00:06.0 to 64 NET: Registered protocol family 17 intel8x0_measure_ac97_clock: measured 67964 usecs intel8x0: clocking to 48000 forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54. ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21 ACPI: PCI Interrupt 0000:00:04.0[A] -> Link [APCH] -> GSI 21 (level, high) -> IRQ 17 PCI: Setting latency timer of device 0000:00:04.0 to 64 eth0: forcedeth.c: subsystem: 0147b:1c01 bound to 0000:00:04.0 eth0: no link during initialization. ip_tables: (C) 2000-2006 Netfilter Core Team eth0: link up. NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8191 buckets, 65528 max) - 224 bytes per conntrack Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory NFSD: starting 90-second grace period nvidia: module license 'NVIDIA' taints kernel. ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19 ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [APC4] -> GSI 19 (level, high) -> IRQ 21 NVRM: loading NVIDIA Linux x86 Kernel Module 1.0-9631 Thu Nov 9 17:38:10 PST 2006 agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0. agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode agpgart: Putting AGP V3 device at 0000:02:00.0 into 8x mode ClusterIP Version 0.8 loaded successfully ipt_recent v0.3.1: Stephen Frost http://snowman.net/projects/ipt_recent/ eth0: no IPv6 routers present eth1394: eth1: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0) netfilter PSD loaded - (c) astaro AG IFWLOG: register target bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3). bootsplash: status on console 0 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3). bootsplash: status on console 1 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3). bootsplash: status on console 2 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3). bootsplash: status on console 3 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3). bootsplash: status on console 4 changed to on bootsplash 3.1.6-2004/03/31: looking for picture...<6>...found (800x600, 12533 bytes, v3). bootsplash: status on console 5 changed to on Shorewall:net2all:DROP:IN=eth0 OUT= MAC= SRC=192.168.0.1 DST=192.168.0.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32771 DPT=7741 LEN=24 bttv0: PLL can sleep, using XTAL (28636363). bttv0: SCERR @ 01ada000,bits: OFLOW FDSR SCERR* bttv0: PLL: 28636363 => 35468950 .. ok bttv0: PLL can sleep, using XTAL (28636363). bttv0: PLL: 28636363 => 35468950 .. ok Shorewall:net2all:DROP:IN=eth0 OUT= MAC= SRC=192.168.0.1 DST=192.168.0.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32772 DPT=7741 LEN=24 FDC 0 is a post-1991 82077 Shorewall:net2all:DROP:IN=eth0 OUT= MAC= SRC=192.168.0.1 DST=192.168.0.255 LEN=44 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=32772 DPT=7741 LEN=24 bttv0: PLL can sleep, using XTAL (28636363). bttv0: PLL: 28636363 => 35468950 .. ok bttv0: PLL can sleep, using XTAL (28636363). bttv0: PLL: 28636363 => 35468950 .. ok
třeba to zabere.. Pročti si ten výše odkazovaný FAQ
#!/bin/bash
#
# Pri pokusu o spusteni alsamixeru chyba:
# alsamixer: function snd_ctl_open failed for default: No such file or directory
# Odebrani modulu - pozor na poradi zalezi!
#
sudo rmmod -v \
snd_via82xx \
snd_ac97_codec \
snd_pcm \
snd_timer \
snd_mpu401_uart \
snd_rawmidi \
snd_seq_device \
btaudio \
bt878 \
bttv \
snd_ac97_bus \
snd_page_alloc \
via82cxxx_audio \
uart401 \
ac97_codec \
snd_mixer_oss \
snd \
sound \
soundcore
# znovuzavedeni modulu pro zvuk
sudo modprobe -v -a \
ac97_codec \
snd_ac97_bus \
snd_page_alloc \
soundcore \
snd_ac97_codec \
snd_pcm snd_timer \
snd \
snd_mpu401_uart \
snd_rawmidi \
snd_seq_device \
sound \
snd_via82xx
# znovuzavedeni modulu pro televizi. Zajimavost: bez teto casti nejde spustit al
samixer
sudo modprobe -v bttv card=42 tuner=1
sudo modprobe -v -a \
btaudio \
# uart401 \
# via82cxxx_audio
Co napriklad k MSP3400 modulu dat parametr amsound=1 ? Ja mam podobnou kartu a musim tam mit "amsound=1 simple=1" (u novejsich je misto 'simple' pouzity 'opmode' parametr).
Jeste to upresnim, kdyz se na tu kartu kouknes a mas na ni MSP3410 obvod, tak tam ma byt to "simple=1". Pokud mas G-ckovou verzi, tak asi simple=2 nebo opmode=2 - viz zdrojak msp3400.c:
#define OPMODE_SIMPLE 1 /* use short programming (>= msp3410 only) */ #define OPMODE_SIMPLER 2 /* use shorter programming (>= msp34xxG) */
Vasek
Ten AMSOUND je pro ty MSP obvody, k TDA9874 Ti nebude nic platny...
Zkus dat na root konzoli "modprobe -v tda9874" to by mohl byt ten audio driver. Pokud to napise neco ve smyslu, ze modul neexistuje, pak je vsechno asi v tvaudio. pak zkus "modprobe -v tvaudio tda9874a=1"
Pokud by to porad neslo, tak koukni semhle: http://www.charmed.com/txt/Insmod-options.txt - jsou tam na vyzkouseni parametry toho tvaudio modulu.
A dej vedet, jak jsi uspel 
Vasek
Tiskni
Sdílej:
ISSN 1214-1267, (c) 1999-2007 Stickfish s.r.o.