Administrace komentářů

Zdravím, zkouším Ubuntu studio 7.04 na notýsku Asus M6A, grafika i915. Problém je v tom, že mi COSI odmítá vzít mnou upravený xorg.conf a stále mi ho "politicky korektně" mění.

>>>>>>>>>>>>>>>>>>>>>>>>>>>

Section "Device"

Option "RenderAccel" "1"

Identifier "Card0"

busid "PCI:0:2:0"

Driver "i810"

VideoRam 65536

VendorName "All"

BoardName "All"

Option "XAANoOffscreenPixmaps" "true"

Option "XaaNoPixmapCache"

Option "DRI" "true"

EndSection

>>>>>>>>>>>>>>>>>>>>>>>>>>

Tohle všechno jsem vygooglil, že by tam mělo patřit. Jenže po restartu tam mám tohle:

>>>>>>>>>>>>>>>>>>>>>>>>>>

Section "Device"

identifier "Card0"

boardname "i810"

busid "PCI:0:2:0"

driver "i810"

screen 0

EndSection

>>>>>>>>>>>>>>>>>>>>>>>>>>

A akcelerace není, glxgears dokážou cca 700fps, direct rendering:no.

V logu nic není, jen v xorg.0.log je asi toto:

>>>>>>>>>>>>>>>>>>>>>>>>>>

(II) Loading sub module "int10"

(II) LoadModule: "int10"

(II) Reloading /usr/lib/xorg/modules//libint10.so

(II) I810(0): initializing int10

(WW) I810(0): Bad V_BIOS checksum

(II) I810(0): Primary V_BIOS segment is: 0xc000

(II) I810(0): VESA BIOS detected

(II) I810(0): VESA VBE Version 3.0

(II) I810(0): VESA VBE Total Mem: 16064 kB

(II) I810(0): VESA VBE OEM: Intel(r)915GM/910ML/915MS Graphics Chip Accelerated VGA BIOS

(II) I810(0): VESA VBE OEM Software Rev: 1.0

(II) I810(0): VESA VBE OEM Vendor: Intel Corporation

(II) I810(0): VESA VBE OEM Product: Intel(r)915GM/910ML/915MS Graphics Controller

(II) I810(0): VESA VBE OEM Product Rev: Hardware Version 0.0

(II) I810(0): Allocated 128 kB for the ring buffer at 0x0

(II) I810(0): Allocating at least 256 scanlines for pixmap cache

(II) I810(0): Initial framebuffer allocation size: 12288 kByte

(II) I810(0): Allocated 4 kB for HW cursor at 0xdfff000 (0x13730000)

(II) I810(0): Allocated 16 kB for HW (ARGB) cursor at 0xdffb000 (0x1dec8000)

(II) I810(0): Allocated 4 kB for Overlay registers at 0xdffa000 (0x13737000).

(II) I810(0): Allocated 64 kB for the scratch buffer at 0xdfea000

drmOpenDevice: node name is /dev/dri/card0

drmOpenDevice: open result is -1, (No such device or address)

drmOpenDevice: open result is -1, (No such device or address)

drmOpenDevice: Open failed

drmOpenDevice: node name is /dev/dri/card0

drmOpenDevice: open result is -1, (No such device or address)

drmOpenDevice: open result is -1, (No such device or address)

drmOpenDevice: Open failed

drmOpenByBusid: Searching for BusID pci:0000:00:02.0

drmOpenDevice: node name is /dev/dri/card0

drmOpenDevice: open result is 8, (OK)

drmOpenByBusid: drmOpenMinor returns 8

drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0

(II) I810(0): [drm] loaded kernel module for "i915" driver

(II) I810(0): [drm] DRM interface version 1.3

(II) I810(0): [drm] created "i915" driver at busid "pci:0000:00:02.0"

(II) I810(0): [drm] added 8192 byte SAREA at 0xdfe5b000

(II) I810(0): [drm] mapped SAREA 0xdfe5b000 to 0xb7a9a000

(II) I810(0): [drm] framebuffer handle = 0xd0020000

(II) I810(0): [drm] added 1 reserved context for kernel

(II) I810(0): Allocated 32 kB for the logical context at 0xdfe2000.

(II) I810(0): Allocated 8192 kB for the back buffer at 0xd000000.

(II) I810(0): Allocated 8192 kB for the depth buffer at 0xc800000.

(II) I810(0): Allocated 36608 kB for textures at 0xc20000

(II) I810(0): 0x81f6de8: Memory at offset 0x00020000, size 12288 kBytes

(II) I810(0): 0x81f8040: Memory at offset 0x0dfff000, size 4 kBytes

(II) I810(0): 0x81f8068: Memory at offset 0x0dffb000, size 16 kBytes

(II) I810(0): 0x81f8094: Memory at offset 0x00000000, size 128 kBytes

(II) I810(0): 0x81f6e28: Memory at offset 0x0dfea000, size 64 kBytes

(II) I810(0): 0x81f82b0: Memory at offset 0x0dffa000, size 4 kBytes

(II) I810(0): 0x81f6fc0: Memory at offset 0x0dfe2000, size 32 kBytes

(II) I810(0): 0x81f6fe0: Memory at offset 0x0d000000, size 8192 kBytes

(II) I810(0): 0x81f7000: Memory at offset 0x0c800000, size 8192 kBytes

(II) I810(0): 0x81f7020: Memory at offset 0x00c20000, size 36608 kBytes

(II) I810(0): Activating tiled memory for the back buffer.

(II) I810(0): Activating tiled memory for the depth buffer.

(II) I810(0): [drm] Registers = 0xfeb80000

(II) I810(0): [drm] ring buffer = 0xd0000000

(II) I810(0): [drm] init sarea width,height = 1280 x 1024 (pitch 2048)

(II) I810(0): [drm] Mapping front buffer

(II) I810(0): [drm] Front Buffer = 0x2a004000

(II) I810(0): [drm] Back Buffer = 0xdd000000

(II) I810(0): [drm] Depth Buffer = 0xdc800000

(II) I810(0): [drm] textures = 0xd0c20000

(II) I810(0): [drm] Initialized kernel agp heap manager, 37486592

(II) I810(0): [dri] visual configs initialized

(==) I810(0): Write-combining range (0xd0000000,0x10000000)

(II) I810(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000

(WW) I810(0): Extended BIOS function 0x5f05 failed.

(II) I810(0): xf86BindGARTMemory: bind key 7 at 0x00fbf000 (pgoffset 4031)

(II) I810(0): xf86BindGARTMemory: bind key 0 at 0x0dfff000 (pgoffset 57343)

(II) I810(0): xf86BindGARTMemory: bind key 1 at 0x0dffb000 (pgoffset 57339)

(II) I810(0): xf86BindGARTMemory: bind key 3 at 0x0dfea000 (pgoffset 57322)

(II) I810(0): xf86BindGARTMemory: bind key 2 at 0x0dffa000 (pgoffset 57338)

(II) I810(0): xf86BindGARTMemory: bind key 4 at 0x0dfe2000 (pgoffset 57314)

(II) I810(0): xf86BindGARTMemory: bind key 5 at 0x0d000000 (pgoffset 53248)

(II) I810(0): xf86BindGARTMemory: bind key 6 at 0x0c800000 (pgoffset 51200)

(--) I810(0): A non-CRT device is attached to pipe B.

No refresh rate overrides will be attempted.

(II) I810(0): Display plane A is disabled and connected to Pipe A.

(II) I810(0): Display plane B is enabled and connected to Pipe B.

(II) I810(0): Enabling plane B.

(II) I810(0): Display plane A is now disabled and connected to Pipe A.

(II) I810(0): Display plane B is now enabled and connected to Pipe B.

(II) I810(0): PIPEACONF is 0x00000000

(II) I810(0): PIPEBCONF is 0x80000000

(II) I810(0): Mode bandwidth is 47 Mpixel/s

(II) I810(0): maxBandwidth is 1216 Mbyte/s, pipe bandwidths are 252 Mbyte/s, 0 Mbyte/s

(**) I810(0): Option "XaaNoPixmapCache"

(**) I810(0): Option "XaaNoOffscreenPixmaps" "true"

(II) I810(0): Using XFree86 Acceleration Architecture (XAA)

Screen to screen bit blits

Solid filled rectangles

8x8 mono pattern filled rectangles

Indirect CPU to Screen color expansion

Solid Horizontal and Vertical Lines

(==) I810(0): Backing store disabled

(==) I810(0): Silken mouse enabled

(II) I810(0): Initializing HW Cursor

(II) I810(0): Set up overlay video

(II) I810(0): Set up textured video

(II) I810(0): X context handle = 0x1

(II) I810(0): [drm] installed DRM signal handler

(II) I810(0): [DRI] installation complete

(II) I810(0): [drm] dma control initialized, using IRQ 16

(II) I810(0): direct rendering: Enabled

(II) I810(0): RandR enabled, ignore the following RandR disabled message.

(WW) I810(0): Option "RenderAccel" is not used

(II) I810(0): Rotating to 0 degrees

(--) RandR disabled

(II) Initializing built-in extension MIT-SHM

(II) Initializing built-in extension XInputExtension

(II) Initializing built-in extension XTEST

(II) Initializing built-in extension XKEYBOARD

(II) Initializing built-in extension XC-APPGROUP

(II) Initializing built-in extension XAccessControlExtension

(II) Initializing built-in extension SECURITY

(II) Initializing built-in extension XINERAMA

(II) Initializing built-in extension XFIXES

(II) Initializing built-in extension XFree86-Bigfont

(II) Initializing built-in extension RENDER

(II) Initializing built-in extension RANDR

(II) Initializing built-in extension COMPOSITE

(II) Initializing built-in extension DAMAGE

(II) Initializing built-in extension XEVIE

drmOpenDevice: node name is /dev/dri/card0

drmOpenDevice: open result is 9, (OK)

drmOpenByBusid: Searching for BusID pci:0000:00:02.0

drmOpenDevice: node name is /dev/dri/card0

drmOpenDevice: open result is 9, (OK)

drmOpenByBusid: drmOpenMinor returns 9

drmOpenByBusid: drmGetBusid reports pci:0000:00:02.0

(WW) AIGLX: 3D driver claims to not support visual 0x23

(WW) AIGLX: 3D driver claims to not support visual 0x24

(WW) AIGLX: 3D driver claims to not support visual 0x25

(WW) AIGLX: 3D driver claims to not support visual 0x26

(WW) AIGLX: 3D driver claims to not support visual 0x27

(WW) AIGLX: 3D driver claims to not support visual 0x28

(WW) AIGLX: 3D driver claims to not support visual 0x29

(WW) AIGLX: 3D driver claims to not support visual 0x2a

(WW) AIGLX: 3D driver claims to not support visual 0x2b

(WW) AIGLX: 3D driver claims to not support visual 0x2c

(WW) AIGLX: 3D driver claims to not support visual 0x2d

(WW) AIGLX: 3D driver claims to not support visual 0x2e

(WW) AIGLX: 3D driver claims to not support visual 0x2f

(WW) AIGLX: 3D driver claims to not support visual 0x30

(WW) AIGLX: 3D driver claims to not support visual 0x31

(WW) AIGLX: 3D driver claims to not support visual 0x32

(II) AIGLX: Loaded and initialized /usr/lib/dri/i915_dri.so

>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>

Nechápu, prostě se mu to nelíbí. Předtím na Mandrivě mi ten konfigurák myslím přesně takhle urychloval. V sekci modules mám všechno, co by tam mělo být, už od instalace...

Díky za radu.