GigaPod IEE 1394/USB 2.0

Ovladač:

v jádře

Technické parametry

Hlinnikovy 3,5" USB 2.0 + firewire box
externy zdroj, usb a firewire (6/6) kabel
usb - do 480Mb/s

firewire - do 400Mb/s

ATA pio mode 0-4
Ultra DMA mode 0-5
Enhanced IDE/ATA/ATAPI protocol

Identifikace pod Linuxem

dmesg:

Firewire:
=========
ieee1394: Current remote IRM is not 1394a-2000 compliant, resetting...
ieee1394: Error parsing configrom for node 0-00:1023
ieee1394: Error parsing configrom for node 0-01:1023
ieee1394: The root node is not cycle master capable; selecting a new root node and resetting...
ieee1394: Node added: ID:BUS[0-00:1023]  GUID[0000000e00000109]
ieee1394: Node changed: 0-00:1023 -> 0-01:1023
ieee1394: unsolicited response packet received - no tlabel match
SCSI subsystem initialized
sbp2: $Rev: 1219 $ Ben Collins 
scsi0 : SCSI emulation for IEEE-1394 SBP-2 Devices
ieee1394: sbp2: Logged into SBP-2 device
ieee1394: Node 0-00:1023: Max speed [S400] - Max payload [2048]
  Vendor: WDC WD20  Model: 00JB-00GVA0       Rev:
  Type:   Direct-Access                      ANSI SCSI revision: 06
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sda: drive cache: write through
SCSI device sda: 390721968 512-byte hdwr sectors (200050 MB)
SCSI device sda: drive cache: write through
 sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

USB:
====
usb 1-1: new full speed USB device using uhci_hcd and address 5
SCSI subsystem initialized
Initializing USB Mass Storage driver...
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
  Vendor: WDC WD20  Model: 00JB-00GVA0       Rev: 08.0
  Type:   Direct-Access                      ANSI SCSI revision: 00
usb-storage: device scan complete
SCSI device sda: 390721969 512-byte hdwr sectors (200050 MB)
sda: assuming drive cache: write through
SCSI device sda: 390721969 512-byte hdwr sectors (200050 MB)
sda: assuming drive cache: write through
 sda: sda1
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0

/proc/bus/usb
T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  5 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=0000 ProdID=0000 Rev= 0.00
S:  SerialNumber=200412280000109
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=  0mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E:  Ad=01(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

Postup zprovoznění pod Linuxem

Skusane na Fedora core 3 (firewire, usb 1.1) a RedHat 7.3 (usb2.0), Pripojenie bez problemov - automaticky vytvorene /dev/sda1 a rucny mount
Pre USB treba pouzit tie iste moduly ako pre flash disky.
Pre Firewire moduly ieee1394,sbp2,ohci1394,sd_mod

Poznámka

Na notebooku mam 4-pinovy konektor pre firewire - disk funguje cez kabel 6/4 pin
Rychlosti firewire/usb2.0 su podobne.
Bez aktivneho chladenia, ale obal je hlinnikovy.
Disk 200GB WD200SE sa iba mierne zohrieva.
Disk WD200 (bez SE) sa podstatne viac zohrieva.

Dokument vytvořil: Zaphod, 17.3.2005 11:24 | Zobrazeno: 930×