IBM kupuje společnost HashiCorp (Terraform, Packer, Vault, Boundary, Consul, Nomad, Waypoint, Vagrant, …) za 6,4 miliardy dolarů, tj. 35 dolarů za akcii.
Byl vydán TrueNAS SCALE 24.04 “Dragonfish”. Přehled novinek této open source storage platformy postavené na Debianu v poznámkách k vydání.
Oznámeny byly nové Raspberry Pi Compute Module 4S. Vedle původní 1 GB varianty jsou nově k dispozici také varianty s 2 GB, 4 GB a 8 GB paměti. Compute Modules 4S mají na rozdíl od Compute Module 4 tvar a velikost Compute Module 3+ a předchozích. Lze tak provést snadný upgrade.
Po roce vývoje od vydání verze 1.24.0 byla vydána nová stabilní verze 1.26.0 webového serveru a reverzní proxy nginx (Wikipedie). Nová verze přináší řadu novinek. Podrobný přehled v souboru CHANGES-1.26.
Byla vydána nová verze 6.2 živé linuxové distribuce Tails (The Amnesic Incognito Live System), jež klade důraz na ochranu soukromí uživatelů a anonymitu. Přehled změn v příslušném seznamu. Tor Browser byl povýšen na verzi 13.0.14.
Byla vydána nová verze 30.0.0 frameworku pro vývoj multiplatformních desktopových aplikací pomocí JavaScriptu, HTML a CSS Electron (Wikipedie, GitHub). Chromium bylo aktualizováno na verzi 124.0.6367.49, V8 na verzi 12.4 a Node.js na verzi 20.11.1. Electron byl původně vyvíjen pro editor Atom pod názvem Atom Shell. Dnes je na Electronu postavena celá řada dalších aplikací.
Byla vydána nová verze 9.0.0 otevřeného emulátoru procesorů a virtualizačního nástroje QEMU (Wikipedie). Přispělo 220 vývojářů. Provedeno bylo více než 2 700 commitů. Přehled úprav a nových vlastností v seznamu změn.
Evropský parlament dnes přijal směrnici týkající se tzv. práva spotřebitele na opravu. Poslanci ji podpořili 584 hlasy (3 bylo proti a 14 se zdrželo hlasování). Směrnice ujasňuje povinnosti výrobců opravovat zboží a motivovat spotřebitele k tomu, aby si výrobky nechávali opravit a prodloužili tak jejich životnost.
Bylo oznámeno (cs) vydání Fedora Linuxu 40. Přehled novinek ve Fedora Workstation 40 a Fedora KDE 40 na stránkách Fedora Magazinu. Současně byl oznámen notebook Slimbook Fedora 2.
ČTK (Česká tisková kancelář) upozorňuje (X), že na jejím zpravodajském webu České noviny byly dnes dopoledne neznámým útočníkem umístěny dva smyšlené texty, které nepocházejí z její produkce. Jde o text s titulkem „BIS zabránila pokusu o atentát na nově zvoleného slovenského prezidenta Petra Pelligriniho“ a o údajné mimořádné prohlášení ministra Lipavského k témuž. Tyto dezinformace byly útočníky zveřejněny i s příslušnými notifikacemi v mobilní aplikaci Českých novin. ČTK ve svém zpravodajském servisu žádnou informaci v tomto znění nevydala.
I'm not going repeat reasons for silencing mice, if you want to do it, you probably know why. If you don't know why, then just assume there are people who hate the clicking sound.
Equipment needed: a Genius Netscroll+ mouse - my original object of experimentation or other type, such as my Dell scroll mouse (seems to be a Logitech) (these two have been proven to work) cross-point screwdriver soldering iron tin-lead solder rosin or flux sharp knife 2 cm of thin insulated wire (2 pcs) (only if necessary)
1. Disassemble the mouse. Now you can see the three switches that make more than 90 % of the noise (the 10 % are made up by resonance in the plastic body - I tried to fill it with some silencing material, but got no audible difference).
2. Take notes on the position of white switch buttons. This step is probably unnecessary, as this seems to be always marked on the pcb's.
3. Carefully solder out the two outer switches. In my first attempt I silenced also the middle switch, which turned to be a bad solution. The switch became too sensitive and could be triggered by mere scrolling. I use the middle button rarely, so I left it noisy in the end; but if you do use the middle button often and therefore wish to hush it too, try it, you have been warned.
4. Open the switch by carefully lifting the legs (perhaps there's better word for it) on its sides.
It's wiser to put the switch upside down beforehand, so that the tiny white plastic button won't fall out. It's not a serious problem if you manage to break the legs - just glue the parts together afterwards - or forget it completely and take the risk of mouse malfunction in extreme conditions (e.g. earthquake).
5. Turn the switch cover by 180 degrees and join it with base again.
before: after:
What is the purpose? This way the point where the button touches the spring is shifted and somehow the spring now moves gradually rather than at once.
The switch lids of the Dell mouse were a bit different, there wasn't enough room to fit the switch after rotation, so I had to make more space with hot solder gun.
6. Solder the switches back to the PCB. They have to be in the same position as in point 2 - if the button was in front, it has to be in front again...
7. In case where only two pins are connected to the circuit (Genius), the pins of the switches are now reversed. To fix it, just connect the outer pins with a piece of wire. (note that this is an old photo, the middle button is no longer silenced and there's no wire there now)
With other type of mouse double check the schematics on how the pins are used.
The Dell mouse has both outer pins grounded, so there's nothing left to do.
8. Reassemble the mouse and enjoy.
You can check recorded sound of clicking before and after. FYI, the sounds are of the Genius mouse, but trust me, the other one is dead silent too, I was just too lazy to record it.Side notes: The disadvantage is, that the actual clicking is perhaps not as distiguishable or maybe accurate (no audio feedback in fact), but it's just a matter of getting used to. Other ways I have tried consisted of shortening the distance the spring has to travel, but the noise reduction gained was not satisfactory for me.. Also the mouse buttons are now more sensitive, so you'll get a few false clicks in the first couple of days, before you learn how to handle it.
Tiskni Sdílej: