Dotaz: dma_intr: error=0x84 { DriveStatusError BadCRC }

[Johny z Podoli]

Ahoj, instaluji "novy" server (firewall + fileserver) jedná se o obyč bastl komp, AMD 700Mhz, 1GB ram, disk IBM 160GB.

disk jede v UDMA-66 ... nesetkali jste se s něčím podobným taky?

NET: Registered protocol family 17
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
ide0: reset: success
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }

Odpovědi

[Johny z Podoli]

info o disku...

/dev/hda:

 Model=HDT722516DLAT80, FwRev=V43OA70A, SerialNo=VD271BTCC5722C
 Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
 RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=51
 BuffType=DualPortCache, BuffSize=7674kB, MaxMultSect=16, MultSect=off
 CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=268435455
 IORDY=on/off, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
 PIO modes:  pio0 pio1 pio2 pio3 pio4
 DMA modes:  mdma0 mdma1 mdma2
 UDMA modes: udma0 udma1 udma2 *udma3 udma4 udma5 udma6
 AdvancedPM=yes: disabled (255) WriteCache=enabled
 Drive conforms to: Reserved:

 * signifies the current active mode

[Zdeněk Burda]

Mrkni se ještěna smartctl -a /dev/hda a taky zkus jiný kabel.

[Johny z Podoli]

nevím, co v tom mám hledat... jedná se o uplně nový disk.

dream:~# smartctl -a /dev/hda
smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     HDT722516DLAT80
Serial Number:    VD271BTCC5722C
Firmware Version: V43OA70A
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 1
Local Time is:    Tue Jan  3 00:15:47 2006 CET
SMART support is: Available - device has SMART capability.
SMART support is: Disabled

SMART Disabled. Use option -s with argument 'on' to enable it.

jdu zkusit ten kabel.

[Johny z Podoli]

Uz jsem si precetl ze je treba smart zapnout... takze tedy:

smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     HDT722516DLAT80
Serial Number:    VD271BTCC5722C
Firmware Version: V43OA70A
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  ATA/ATAPI-7 T13 1532D revision 1
Local Time is:    Tue Jan  3 00:18:12 2006 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x00) Offline data collection activity
                                        was never started.
                                        Auto Offline Data Collection: Disabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                 (3385) seconds.
Offline data collection
capabilities:                    (0x5b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        No Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        (  57) minutes.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000b   100   100   016    Pre-fail  Always       -       0
  2 Throughput_Performance  0x0005   100   100   050    Pre-fail  Offline      -       0
  3 Spin_Up_Time            0x0007   122   122   024    Pre-fail  Always       -       319 (Average 254)
  4 Start_Stop_Count        0x0012   100   100   000    Old_age   Always       -       23
  5 Reallocated_Sector_Ct   0x0033   100   100   005    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000b   100   100   067    Pre-fail  Always       -       0
  8 Seek_Time_Performance   0x0005   100   100   020    Pre-fail  Offline      -       0
  9 Power_On_Hours          0x0012   100   100   000    Old_age   Always       -       2851
 10 Spin_Retry_Count        0x0013   100   100   060    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       23
192 Power-Off_Retract_Count 0x0032   100   100   050    Old_age   Always       -       142
193 Load_Cycle_Count        0x0012   100   100   050    Old_age   Always       -       142
194 Temperature_Celsius     0x0002   166   166   000    Old_age   Always       -       33 (Lifetime Min/Max 22/43)
196 Reallocated_Event_Count 0x0032   100   100   000    Old_age   Always       -       0
197 Current_Pending_Sector  0x0022   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0008   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x000a   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 91 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 91 occurred at disk power-on lifetime: 2851 hours (118 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 7e 32 99 e0  Error: ICRC, ABRT at LBA = 0x0099327e = 10039934

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 40 3f 2b 99 e0 00      01:02:01.100  WRITE DMA EXT
  35 00 50 e7 2a 99 e0 00      01:02:01.100  WRITE DMA EXT
  35 00 08 d7 2a 99 e0 00      01:02:01.100  WRITE DMA EXT
  35 00 08 97 c6 00 e0 00      01:02:01.100  WRITE DMA EXT
  35 00 c8 cf c5 00 e0 00      01:02:01.100  WRITE DMA EXT

Error 90 occurred at disk power-on lifetime: 2851 hours (118 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 1e 06 38 e5  Error: ICRC, ABRT at LBA = 0x0538061e = 87557662

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 10 0f 06 38 e0 00      00:51:58.200  WRITE DMA EXT
  35 00 10 ef 05 38 e0 00      00:51:58.200  WRITE DMA EXT
  35 00 08 cf 05 38 e0 00      00:51:58.200  WRITE DMA EXT
  35 00 08 b7 05 38 e0 00      00:51:58.200  WRITE DMA EXT
  35 00 08 9f 05 38 e0 00      00:51:58.200  WRITE DMA EXT

Error 89 occurred at disk power-on lifetime: 2851 hours (118 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 d6 0d 99 e0  Error: ICRC, ABRT at LBA = 0x00990dd6 = 10030550

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 00 d7 05 99 e0 00      00:51:24.700  WRITE DMA EXT
  35 00 18 bf 00 99 e0 00      00:51:24.700  WRITE DMA EXT
  35 00 50 67 00 99 e0 00      00:51:24.700  WRITE DMA EXT
  35 00 08 57 00 99 e0 00      00:51:24.700  WRITE DMA EXT
  35 00 08 a7 b7 00 e0 00      00:51:24.700  WRITE DMA EXT

Error 88 occurred at disk power-on lifetime: 2851 hours (118 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 36 d2 39 e5  Error: ICRC, ABRT at LBA = 0x0539d236 = 87675446

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 60 d7 d1 39 e0 00      00:51:23.700  WRITE DMA EXT
  35 00 38 b7 c1 8d e0 00      00:51:23.700  WRITE DMA EXT
  35 00 18 6f f4 9f e0 00      00:51:23.700  WRITE DMA EXT
  25 00 08 3f 01 3b e0 00      00:51:23.500  READ DMA EXT
  25 00 08 77 00 39 e0 00      00:51:23.500  READ DMA EXT

Error 87 occurred at disk power-on lifetime: 2851 hours (118 days + 19 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  84 51 00 16 8d 00 e0  Error: ICRC, ABRT at LBA = 0x00008d16 = 36118

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  35 00 50 c7 8c 00 e0 00      00:46:14.900  WRITE DMA EXT
  35 00 c8 3f e3 9f e0 00      00:46:14.900  WRITE DMA EXT
  35 00 48 27 e2 9f e0 00      00:46:14.900  WRITE DMA EXT
  35 00 60 bf e1 9f e0 00      00:46:14.900  WRITE DMA EXT
  35 00 08 bf 8c 00 e0 00      00:46:14.900  WRITE DMA EXT

SMART Self-test log structure revision number 1
No self-tests have been logged.  [To run self-tests, use: smartctl -t]


Warning! SMART Selective Self-Test Log Structure error: invalid SMART checksum.
SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

[Johny z Podoli]

jeste snad tohle....

0000:00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] (rev 03)
0000:00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
0000:00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 22)
0000:00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 10)
0000:00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
0000:00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 10)
0000:00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 30)
0000:00:08.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 34)
0000:00:09.0 Ethernet controller: 3Com Corporation 3c905B 100BaseTX [Cyclone] (rev 30)
0000:00:11.0 VGA compatible controller: S3 Inc. ViRGE/DX or /GX (rev 01)
0000:00:13.0 Unknown mass storage controller: Triones Technologies, Inc. HPT366/368/370/370A/372 (rev 03)

[Ritchie]

Setkali a vyřešili reklamací.

[Johny z Podoli]

pokud se nepletu, tak se jedná o jiný problém, navíc tento disk v jiném PC funguje naprosto korektně.

Johny

[Ritchie]

Chyba může být v řadiči, kabelu, disku. Chipset KT133 měl prý problémy s DMA přenosy. Vyskytuje se chyba deterministicky nebo náhodně?

[Johny z Podoli]

Pravda je, že obecně tento komp už měl jednou s 80GB seagatem problém - nechtěl vubec naběhnout a hlásil samou chybu. Pak se to "samo" vyřešilo.

Jinak používám už třetí zcela novej 80žil. kabel. Chyba se vyskytuje výhradně při větším množství přístupů na disk, specialně třeba při tarování a podobně.

Johny

[Thunder.m]

S tím přesně ty staré desky s KT133 měly problémy, zkus update biosu, nebo jádra, jestli máš nějaké starší než 2.6.14

[Johny z Podoli]

mám 2.6.8, kernel 2.6.14 to řeší?

[David Jež]

Spíše než magii zkus standardní postup pro tyto případy: Povolit nebo zakázat CONFIG_IDEDISK_MULTI_MODE, CONFIG_IDEDMA_IVB a zkontroluj jestli máš také podporu pro svůj řadič.
-djz