Dotaz: USB2IDE s chipem OnSpec 90c36

[kapo]

Mam tuto (http://www.part2.com/spec/storage/ca805puh.html) redukci z USB na IDE. Je na ni chip OnSpec 90c36. Na strankach vyrobce se zminuji, ze tento cip je podporovan linuxem od verze jadra 2.4.0. Me to ale za boha nejde rozchodit. Mam scsi podporu, mass-storage modul. Zarizeni je nepoznane. Vendor=0x55aa, product=0x100. Ten vendor je zajimavy, nevim, kde se tam sebralo zrovna takove cislo. Pod WinXP jede, takze problem bude v softu. Nema nekdo zkusenosti, kde hledat atp.? Diky moc za jakekoliv nakopnuti.

P.S.zkousel jsem i jadro 2.6.0, problem zustava - nepoznane

Karel Podvolecky

Odpovědi

[Peter Golis]

predpokladam, ze mas podporu.:
usb, usb mass storrage,
scsi, scsi generic, scsi disk
Co pise dmesg?

[kapo]

"strucny" vypis dmesg. podpora scsi jede (cdrom, disk, generic), usb mass storage taky. jen ho to nepozna.

usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
uhci.c: USB UHCI at I/O 0xe400, IRQ 5
usb.c: new USB bus registered, assigned bus number 1
uhci.c: detected 2 ports
usb.c: kmalloc IF f7e579c0, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI-alt Root Hub
SerialNumber: e400
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface f7e579c0
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
uhci.c: USB UHCI at I/O 0xe000, IRQ 5
usb.c: new USB bus registered, assigned bus number 2
uhci.c: detected 2 ports
usb.c: kmalloc IF f7e57bc0, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI-alt Root Hub
SerialNumber: e000
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface f7e57bc0
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik vojtech@suse
hid-core.c: USB HID support drivers
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 88k freed
uhci.c: root-hub INT complete: port1: 48a port2: 48a data: 6
uhci.c: e400: suspend_hc
hub.c: port 1, portstatus 100, change 3, 12 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 100, change 3, 12 Mb/s
hub.c: port 2, portstatus 100, change 3, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 100, change 3, 12 Mb/s
uhci.c: root-hub INT complete: port1: 5ab port2: 49b data: 6
hub.c: port 1, portstatus 301, change 3, 1.5 Mb/s
hub.c: port 1 connection change
hub.c: port 1, portstatus 301, change 3, 1.5 Mb/s
hub.c: port 1, portstatus 301, change 2, 1.5 Mb/s
uhci.c: root-hub INT complete: port1: 488 port2: 488 data: 6
hub.c: port 1, portstatus 301, change 2, 1.5 Mb/s
uhci.c: root-hub INT complete: port1: 5a9 port2: 49b data: 6
hub.c: port 1, portstatus 301, change 2, 1.5 Mb/s
uhci.c: root-hub INT complete: port1: 488 port2: 488 data: 6
hub.c: port 1, portstatus 301, change 2, 1.5 Mb/s
hub.c: port 1, portstatus 303, change 0, 1.5 Mb/s
hub.c: new USB device 00:11.2-1, assigned address 2
uhci.c: root-hub INT complete: port1: 595 port2: 49b data: 4
usb.c: kmalloc IF f7d5d140, numif 1
usb.c: skipped 1 class/vendor specific interface descriptors
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Manufacturer: Logitech
Product: USB-PS/2 Optical Mouse
input0: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb2:2.0
usb.c: hid driver claimed interface f7d5d140
usb.c: kusbd: /sbin/hotplug add 2
hub.c: port 2, portstatus 101, change 3, 12 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 3, 12 Mb/s
uhci.c: root-hub INT complete: port1: 488 port2: 488 data: 6
hub.c: port 2, portstatus 101, change 2, 12 Mb/s
uhci.c: root-hub INT complete: port1: 5a5 port2: 499 data: 4
hub.c: port 2, portstatus 101, change 2, 12 Mb/s
uhci.c: root-hub INT complete: port1: 488 port2: 488 data: 6
hub.c: port 2, portstatus 101, change 2, 12 Mb/s
uhci.c: root-hub INT complete: port1: 5a5 port2: 499 data: 4
hub.c: port 2, portstatus 101, change 2, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: new USB device 00:11.2-2, assigned address 3
usb.c: kmalloc IF f7d5d440, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 3 default language ID 0x409
Manufacturer: OnSpec Electronic Inc.
Product: USB Disk
SerialNumber: 004410121231
usb.c: unhandled interfaces on device
usb.c: USB device 3 (vend/prod 0x55aa/0x100) is not claimed by any active driver.
  Length              = 18
  DescriptorType      = 01
  USB version         = 1.00
  Vendor:Product      = 55aa:0100
  MaxPacketSize0      = 8
  NumConfigurations   = 1
  Device version      = 0.08
  Device Class:SubClass:Protocol = ff:00:00
    Vendor class
Configuration:
  bLength             =    9
  bDescriptorType     =   02
  wTotalLength        = 0020
  bNumInterfaces      =   01
  bConfigurationValue =   01
  iConfiguration      =   00
  bmAttributes        =   40
  MaxPower            =    0mA

  Interface: 0
  Alternate Setting:  0
    bLength             =    9
    bDescriptorType     =   04
    bInterfaceNumber    =   00
    bAlternateSetting   =   00
    bNumEndpoints       =   02
    bInterface Class:SubClass:Protocol =   05:00:00
    iInterface          =   00
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   01 (out)
      bmAttributes        =   02 (Bulk)
      wMaxPacketSize      = 0040
      bInterval           =   00
    Endpoint:
      bLength             =    7
      bDescriptorType     =   05
      bEndpointAddress    =   82 (in)
      bmAttributes        =   02 (Bulk)
      wMaxPacketSize      = 0040
      bInterval           =   00
usb.c: kusbd: /sbin/hotplug add 3
hub.c: port 1, portstatus 303, change 0, 1.5 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: port 1, portstatus 100, change 2, 12 Mb/s
hub.c: port 1 enable change, status 100
hub.c: port 2, portstatus 100, change 2, 12 Mb/s
hub.c: port 2 enable change, status 100
Adding Swap: 128480k swap-space (priority -1)

jsou tam zaply detailni vypis u USB (debug). Proste potrebuju najit ovladac, co si rozumi s tim cipem 90c36. Diky,

P.S.Omlouvam se za ten debilni format, ale nevim, jak ho donutit, aby mi to normalne radkovalo.

[unchallenger]

Uááááá! Donutit k zachování formátování to lze snadno pomocí PRE tagu. Možná by to bylo lepší jen nalinkovat, pokud to máš kam umístit na web...

---

4Leoš Literák: prosím dopiš někam k ,,jak zadávat dotaz`` také ,,jak používat HTML pre tag``, jen já sám už na tohle odpovídám tak po desáte...

[kapo]

Tak se mi to povedlo, tady je odkaz. Ale nebude fungovat porad, bohuzel. Ale ten PRE tag stejne nevim co je. Asi se to html budu muset trochu naucit.

[kapo]

Tak uz jsem na to prisel. Nebudu to posilat znovu cele, jen par relevantnich radek:

...
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
...
...
hub.c: port 2, portstatus 101, change 3, 12 Mb/s
hub.c: port 2 connection change
...
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: new USB device 00:11.2-2, assigned address 3
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=3
usb.c: USB device number 3 default language ID 0x409
Manufacturer: OnSpec Electronic Inc.
Product: USB Disk
SerialNumber: 004410121231
usb.c: unhandled interfaces on device
usb.c: USB device 3 (vend/prod 0x55aa/0x100) is not claimed by any active driver.
  Length              = 18
  DescriptorType      = 01
  USB version         = 1.00
  Vendor:Product      = 55aa:0100
  MaxPacketSize0      = 8
  NumConfigurations   = 1
  Device version      = 0.08
  Device Class:SubClass:Protocol = ff:00:00
    Vendor class
Configuration:
...
            

[Jan Matuštík]

text mezi

 a 

je zobrazen přesně tak, jak je napsaný - vč. více mezer, nových řádků.

[Jan Matuštík]

* mezi >pre< a >/pre<

[Peter Golis]

Nikde v dmesg nevidim poznamku o sg (scsi generic, pre disky), su tam hlasky len o sr {sr_mod} ktory je pre cdrom.
skus

modprobe -v sg

Disk ti to naslo, ale nevedelo robit s scsi hdd. Nasiel som tam na ide radici 7x vypalovacku. Kde si zohnal taky radic? K tej vypalovacke: Naslo ti ju 7x na ide radici. Naozaj ich mas na ide radici 7 (taky radic chcem)? Ak je len jedna, tak by som odporucil prelozit precisteny (make mrproper, make menuconfig,...) a nanovo skonfigurovany kernel. Mozno ti tam ostal nejaky balast z patch-ov.

[kapo]

scsi podpora pro disk je zakompilovana, ale scsi generic jako modul. tak to asi nebude to pravy orechovy. zkusim ten kernel procistit a uvidim. zatim dik.

[Peter Golis]

Ani nie, bud budes zakazdym ten modul zavadzat rucne, alebo si das cez hotplug (/etc/hotplug/) zavadzanie toho modulu cez nejaku blbinku.
Alebo to precistis a das do jadra co potrebujes ja tak fungujem na oboch usb mass storrage zariadeniach co tu mam zapisane.

Len keby si nahodou pridal skutocny scsi disk, tak na to nesmies zabudnut, aby ti ho uzivatelia (omylom) nezlikvidovali.

[kapo]

muzes mi prosim jeste napsat, jake jsou vendor/product tech Tvych dvou usb disku? Dival jsem se na netu a nikde jsem to nenasel (google) zarizeni s takovym ID. Diky.

[Peter Golis]

hehe.:
>co tu mam zapisane.
http://abclinuxu.cz/Profile?userId=1845

Inac ked sa to podpisalo ako standardne usb-mass-storrage, tak nie je o com. Obcas, ked vies, ze to je usb-mass-storrage, ale linux ho nenajde, staci velakrat dane zariadenie predefinovat v /usr/src/linux/drivers/usb/storage/unusual_devs.h. I ked v 2.4.22-pre(myslim ze 4) boli rozsiahle cistky usb. Takze dokonca ani na n5510 nepotrebujem ten patch keby si chcel, poslem ti moj konfig.

[kapo]

Ufff, do toho souboru (unusual_devs.h) jsem se dival, ale bliz jsem to neprohlizel. Narazil jsem na ten muj vendor 0x55aa, ale nevim co s tim kde udelat. Jestli mas nejaky priklad, nebo odkaz co a jak asi zmenit, tak mi to posli pls na email (treba i s tim konfigem) mel by byt v profilu, ale pro jistotu kapo.c@tiscali.cz .

[Peter Golis]

ok, mas to v poste. Je to rozlezene po celom konfigu, takze si ho prejdi a porovnaj s tvojim, aspon by ocko.

[kapo]

Tak jsem se podival na ten Tvuj config. (mimo misu: je dobry k necemu mit zaply APIC a NUMA na jednom procaku, nebo jich tam mas vic ) A taky jsem trochu laboroval. Vsechno jsem dal jako moduly a zkousel.
Vysledek:
  Jak jsem se domnival na zacatku, chyba bude nekde u ovladace USB, ktery si neporozumi s tim cipem. Kdyz jsem nemel nactenou SCSI podporu pro disk, tak to poznalo vsecko v pohode, jak by melo. pak jsem pridal modul sd_mod a vytuhlo to. pokud jsem vytahl USB z disku, tak to dokoncilo, ale nepoznal parametry disku (velikost, sector size). V hlaseni zustal TYPE: direct-access. Ted nemuzu bohuzel poslat cely log. Jeste vyzkousim laborovat se temi parametry v unusual-dev.h. jsou tam ty US_SC_BULK a pod, zatim nevim co presne znamenaji. Ale myslim, ze to stejne asi bude prd platny. Nicmene zkusim zitra postnout jeste ten log.