Dotaz: rt2400 - RED HAT

[Laci]

Uz par dni sa pokusam nainstalivat sietovku ASUS WL-130b pod linuxom RED HAT 9.0 zatial neuspesne. Postupujem podla manualu ale ked zadam "make install" vypisuje:

depmod: *** Unresolved symbols in /lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o

append 'alias ra0 rt2400' to /etc/modules.conf

Podla manualu co je dole: "If not on Red hat Linux, the module will be put in the right place, but the boot script setup will fail." Neviete co je potrebne robit inak alebo kde to skopirovat pri RED HAT??? Dakujem.

Compile the RT2400 Module*********************************

Open a console or xterm (a command prompt window). A more or less standard way of compiling software has been developed. You execute a series of commands - usually in the directory where "Configure" script is for the source you extracted.

1. ./Configure (checks your system to see if "make" has what it needs)

2. make (compiles and links the source into executable program files)

3. use "su" to make yourself super-user (root)

4. make install (This runs a script that places the compiled files where they can be used. If not on Red hat Linux, the module will be put in the right place, but the boot script setup will fail. That is probably a good thing - depending on your distro)

5. Exit from super user by typing 'exit'. If the above commands worked without an error (other than failing to place the boot script on non-Red Hat systems), the driver should now be compiled and in place. NOTE: The ./Configure will probably not work if your kernel source is not properly installed. Otherwise...carry on with the make as above. ....

Odpovědi

[obonsky]

Ja mam podobnu sietovku, ale s chipsetom rt2500. Nenapisal si, ake ovladace sa pokusas nainstalovat. Ja som mal podobne problemy s ovladacmi z ralinktech.com, su upravene na konkretne jadro z niekolkych distribucii a pokial mas ine, si odpisany (to je asi tvoj pripad, skus si pozriet tie instalacne skripty). Uz nejaku dobu pouzivam ndiswrapper s XP ovladacmi a som spokojny. http://ndiswrapper.sourceforge.net

[m0d0r]

hmm naco ndiswrapper ked mas fungujuce linux ovladace ? ? ? ? na linku dole ?

[Tomas F.]

http://rt2400.sourceforge.net/

[Laci]

http://rt2400.sourceforge.net/ presne odtialto som ovladace stiahol ale ja mam problem rozchodit to pod RED HAT linuxom.

[obonsky]

A mas zdrojaky aktualneho jadra v /usr/src/linux ?

[Laci]

ked zadam modprobe:

Pricom rt2400.o je na tom mieste kde to vypisuje

[root@lacik root]# modprobe rt2400

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol __netdev_watchdog_up

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol eth_type_trans

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol filp_open

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol alloc_skb

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol pci_free_consistent

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol alloc_etherdev

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol unregister_netdev

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol pci_alloc_consistent

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol filp_close

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol register_netdev

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol netif_rx

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol skb_over_panic

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: unresolved symbol softnet_data

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: insmod /lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o failed

/lib/modules/2.4.20-8/kernel/drivers/net/wireless/rt2400.o: insmod rt2400 failed

[obonsky]

K mojej predoslej otazke - mas distribucne jadro, alebo vlastne? Ak ho mas priamo z distribucie, mal by si v /usr/src/ rozbalit jeho zdrojaky, daj na adresar simlink linux ( t.j. /usr/src/linux). Don potom skopiruj z /boot/ subor config... pre aktualne jadro pod nazvom .config a skompiluj si kernel. Neinstaluj moduly ani jadro, staci, ked bude skompilovane. Potom skus instalovat ovladace este raz.

[Laci]

Diki za radu ale mam v tom trosku chaos, kedze linux mam nainstalovany asi tyzden potreboval by som este presnejsie vysvetlenie. Cize: Mam distribucne jadro. V adresary /usr/src/ mam podadresare 'linux-2.4.20-8'-asi 160MB, 'linux-2.4' (ktory je odkazom na adresar 'linux2.4.20-8') a adresar 'redhat'-prazdny . Zdrojaky jadra najdem na CD ako jeden balik? Config umiestnit do /usr/src/linux? A potom mam skompilovat kernel, cize cele jadro prikazom 'make'? Dik PS:Zaciatky su tazke. ;o(

[obonsky]

Zaciatky su vzdy tazke, verziu aktualneho jadra zistis pomocou prikazu "uname -a". Zrejme je to prave jadro 2.4.20-8. Skus si pozriet clanok http://www.abclinuxu.cz/clanky/show/59472, kde je popisana kompilacia jadra. Pri jadrach 2,4 je to make dep, make clean, make bzImage, make modules ( ma malo by byt aj make modules_install, ale to nedavaj, to uz je hotove). Potom by si mal mat v adresary /usr/src/linux... skompilovane vsetko pre aktualne jadro. A mozes skusit znovu nainstalovat ovladace.