Administrace komentářů

Ahoj, mam problem s nativnym rozlisenim u monitoru Belinea 102035W v kombinacii s grafikou Nvidia Geforce FX 5200 (od Asusu). Monitor je pripojeny cez DVI, VGA na grafike nieje.

Najprv udaje o monitore: 31-83KHz, 56-75Hz, 160Mhz max, nativne 1680x1050@60Hz.

Distribucia: Ubuntu 5.10 + ovladace nvidia

Podstatna cast xorg.conf

Section "Module"
#	Load	"GLcore"
	Load	"bitmap"
	Load	"ddc"
#	Load	"dri"
	Load	"extmod"
	Load	"freetype"
	Load	"glx"
	Load	"int10"
	Load	"type1"
	Load	"vbe"
EndSection

Section "Device"
	Identifier	"NVIDIA Corporation NV34 [GeForce FX 5200]"
	Driver		"nvidia"
	BusID		"PCI:1:0:0"
EndSection

Section "Monitor"
	Identifier	"B102035W"
	Option		"DPMS"
	HorizSync    31.0 - 83.0
	VertRefresh  56.0 - 75.0
	Option	     "DPMS"
EndSection

Section "Screen"
	Identifier	"Default Screen"
	Device		"NVIDIA Corporation NV34 [GeForce FX 5200]"
	Monitor		"B102035W"
	DefaultDepth	24
	SubSection "Display"
		Depth		1
		Modes		"1680x1050" "1600x1200" "1280x1024" 
	EndSubSection
	SubSection "Display"
		Depth		4
		Modes		"1680x1050" "1600x1200" "1280x1024" 
	EndSubSection
	SubSection "Display"
		Depth		8
		Modes		"1680x1050" "1600x1200" "1280x1024" 
	EndSubSection
	SubSection "Display"
		Depth		15
		Modes		"1680x1050" "1600x1200" "1280x1024" 
	EndSubSection
	SubSection "Display"
		Depth		16
		Modes		"1680x1050" "1600x1200" "1280x1024" 
	EndSubSection
	SubSection "Display"
		Depth		24
		Modes		"1680x1050" "1600x1200" "1280x1024"
		Virtual 	1680 1050
	EndSubSection
EndSection

A co sa mi nepaci v Xorg.0.log:

(II) NVIDIA(0): NVIDIA GPU detected as: GeForce FX 5200
(--) NVIDIA(0): VideoBIOS: 04.34.20.87.00
(--) NVIDIA(0): Interlaced video modes are supported on this GPU
(II) NVIDIA(0): Detected AGP rate: 4X
(--) NVIDIA(0): VideoRAM: 131072 kBytes
(II) NVIDIA(0): Connected display device(s): DFP-0
(--) NVIDIA(0): DFP-0: maximum pixel clock: 135 MHz
(--) NVIDIA(0): DFP-0: Internal Single Link TMDS
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Reloading /usr/X11R6/lib/modules/libddc.a
(II) NVIDIA(0): B102035W: Using hsync range of 31.00-83.00 kHz
(II) NVIDIA(0): B102035W: Using vrefresh range of 56.00-75.00 Hz
(II) NVIDIA(0): Clock range:  12.00 to 135.00 MHz

So 135 MHz sa ani 1600x1200 ani 1650x1050 rozbehat bohuzial neda. Pridavat modeline nema zmysel, vsetky rozumne su v intervale 145-155Mhz. Pridanie

Option	"NODDC"      "1"

do xorg.conf tiez nepomaha nema na vysledok ziaden efekt.

S ovladacom "nv" som uspech tiez nemal, tu je cast (asi aj s dovodom) Xorg.0.log:

(II) NV(0): Supported additional Video Mode:
(II) NV(0): clock: 146.2 MHz   Image Size:  433 x 270 mm
(II) NV(0): h_active: 1680  h_sync: 1784  h_sync_end 1960 h_blank_end 2240 h_border: 0
(II) NV(0): v_active: 1050  v_sync: 1053  v_sync_end 1059 v_blanking: 1089 v_border: 0
(II) NV(0): Ranges: V min: 56  V max: 75 Hz, H min: 31  H max: 83 kHz, PixClock max 150 MHz
(II) NV(0): Monitor name: B102035W
(II) NV(0): Probing for EDID on I2C bus B...
(II) NV(0): I2C device "DDC:ddc2" registered at address 0xA0.
(II) NV(0): I2C device "DDC:ddc2" removed.
(II) NV(0):   ... none found
(--) NV(0): CRTC 0 is currently programmed for DFP
(II) NV(0): Using DFP on CRTC 0
(--) NV(0): Panel size is 1280 x 1024
(--) NV(0): VideoRAM: 131072 kBytes
(==) NV(0): Using gamma correction (1.0, 1.0, 1.0)
(II) NV(0): B102035W: Using hsync range of 31.00-83.00 kHz
(II) NV(0): B102035W: Using vrefresh range of 56.00-75.00 Hz
(II) NV(0): Clock range:  12.00 to 350.00 MHz
(II) NV(0): Mode "1680x1050@60" is larger than BIOS programmed panel size of 1280 x 1024.  Removing.

Vobec netusim, co je BIOS programmed panel size a ci sa da zmenit.

Zaujimave je, ze pokial bol monitor napojeny cez VGA na grafike i845 (driver "i810"), DDC udavalo maximum pixelclock 150Mhz. Grafika vsak 1680x1050 nezvladla.

Vobec tomu nerozumiem. Na googli ani na ubuntuforums som sa ziadne podstatne informacie nedozvedel. Prosim o akekolvek tip-y.