Administrace komentářů

Tak sem metodou pokus/omyl připojil na pin 4 GND , na pin 3 TXD , na pin 2 RXD , nastavil rychlost , spistil to a ejhle , zobrazení funguje. Vypadá to následovně :

UART1 output test ok

Uart init

mfid=000000c2 devid=00002249

Found 1 x 2M flash memory


---RealTek(RTL8186)at 2006.02.13-13:32+0800 version 1.4 [16bit](180MHz)

no sys signature at 00010000!

sys checksum error at 00020000!

Jump to image start=0x80300000...

display on
entering boot loader, turning on display
decompressing kernel:
UNCOMPRESS_OUT: 80000000 FREEMEM_START: 00000000 FREEMEM_END: 80800000
UNCOMPRESS_OUT: 80000000 FREEMEM_START: 80393d94 FREEMEM_END: 80800000
Uncompressing Linux... done, booting the kernel.
done decompressing kernel.
jump kernel=80000000!
early printk enabled 

Determined physical RAM map:

 memory: 01000000 @ 00000000 (usable)

On node 0 totalpages: 4096

zone(0): 4096 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: root=/dev/mtdblock1 console=0 single

Calibrating delay loop... 178.99 BogoMIPS

Memory: 14116k/16384k available (1702k kernel code, 2268k reserved, 104k data, 52k init, 0k highmem)

Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)

Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 4096 (order: 2, 16384 bytes)

check_wait... unavailable.

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

Serial driver version 6.02 (2003-03-12) with no serial options enabled

ttyS00 at 0x00c3 (irq = 3) is a rtl_uart1

state->flags=00000000

Realtek GPIO Driver for Flash Reload Default

RTL8186LED: Led driver registered (c)wwarczak@online.pl

led0: Initialized.

led1: Initialized.

led2: Initialized.

led3: Initialized.

block: 64 slots per queue, batch=16

NET4: APPro54G voip/icmp fast path installed

PPP generic driver version 2.4.1

PPP Deflate Compression module registered

PPP BSD Compression module registered

MPPE/MPPC encryption/compression module registered

RealTek E-Flash System Driver. (C) 2002 RealTek Corp.

Flash primary chip mfid: 194 devid 8777

Flash secondary chip mfid: 16448 devid 16448

Found 1 x 2M Byte MXIC MX29LV160CB at 0xbe000000

Offset: 0x0, erasesize: 0x4000, numblocks: 1

Offset: 0x4000, erasesize: 0x2000, numblocks: 2

Offset: 0x8000, erasesize: 0x8000, numblocks: 1

Offset: 0x10000, erasesize: 0x10000, numblocks: 31

Creating 2 MTD partitions on "DiskOnChip Millennium":

0x00000000-0x00200000 : "boot+cfg+linux"

0x000c0000-0x001f0000 : "root fs"

NVRAM: 00006000 000000e8 on "boot+cfg+linux"

NVRAM: HW checksum ok

NVRAM: Autodetecting PHY for port 0 id: 8201

NVRAM: Autodetecting PHY for port 1 id: 8201

NVRAM: Nvram hw.conf handler installed

NVRAM: Flash writer handler installed

NVRAM: Searching licence data on "boot+cfg+linux"

NVRAM: flash data initialized

NVRAM: licence data initialized, name: APPro54G, type: 1

NVRAM: Nvram licence.conf handler installed

NVRAM: Nvram system.conf handler installed

rtl8186_init: Loading new ethernet driver!!

8186NIC Ethernet driver v0.0.4 (Sep 23, 2005)

eth0: RTL8186-NIC at 0xbd200000, 00:01:02:03:04:05, IRQ 4

eth1: RTL8186-NIC at 0xbd300000, 04:05:06:07:08:09, IRQ 5

nat_speed_init (v1.2) 

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 1024 bind 2048)

ip_conntrack version 2.1 (128 buckets, 1024 max) - 312 bytes per conntrack

PPTP netfilter connection tracking: registered

PPTP netfilter NAT helper: registered

ip_tables: (C) 2000-2002 Netfilter core team

IPP2P v0.8.2 loading

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

NET4: Ethernet Bridge 008 for NET4.0

NET4: Bridge Netfilter support (c)wwarczak@online.pl 

NET4: Bridge Netfilter proc handler installed

VFS: Mounted root (squashfs filesystem) readonly.

Freeing unused kernel memory: 52k freed

mount /proc file system ok!

mount /tmpfs  file system ok!

starting /bin/boot.sh!

Algorithmics/MIPS FPU Emulator v1.5

_STOR 158 184 071 227 231 132 225 024 006 197 165 079 107 117 055 029

_STOR 158 184 071 227 231 132 225 024 006 197 165 079 107 117 055 029

_STOR 249 034 147 180 214 060 189 098 083 217 167 246 207 129 179 144

RTL8186 SOC AP software written by wwarczak@online.pl, hw: 16MB_UNKNOWN
GPL source code: http://approsoftware.com/download/rtl8186/src/
Tech support http://approsoftware.com/, licence: SOFT
Unpacking filesystem
APPro54G licence OK
Device HW_ID: **-**-**-**-**-**-**-**-**-**-**-**-**-**-**-**, licence: SOFT
Restoring user scripts
Device type: Ovislink 5460
Restoring configuration
INIT: Config OK
Starting init

init started:  BusyBox v1.00 (2010.02.22-17:10+0000) multi-call binary

Please press Enter to activate this console. Jan  1 01:00:34 crond[359]: crond 2.3.2 dillon, started, log level 8

Nefunguje ale psaní (jen příjem) ale to jen v programu moserial.

Zkusil sem    v terminálu     
sudo setserial -g /dev/ttyUSB[0]
screen /dev/ttyUSB0 38400 

a jede to ..  Takže zapojení považujte za vyřešené ...