Administrace komentářů

1. A system with 2 ODDs attached to a Sii3512 may not boot.

Presto jsem se pokusil flashnout, ale problem je ze cip ktery radic ma (vyrobce ST-Lab) je ht27c010-70, vyzkousel jsem vsechny podporovane chipy ktere mely take 1mb, z nasledujiciho seznamu :

AMD’s Am29F010B/Am29LV010B (1 Megabit) and Am29F040B (4 Megabit)
AMD’s Am29LV400B (4 Megabit) variable sectors
Atmel’s AT49BV512 (64KB), AT29LV010A (1 Megabit), and AT49LV040 (4 Megabit)
SST’s 39SF010 (1 Megabit), 39VF010 (1 Megabit), 39VF020 (2 Megabit), 39SF020 (2 Megabit), and 39VF040 (4 Megabit).
SANYO’s LE28C1001D (1 Megabit)
WinBound’s 29EE011 (1 Megabit) and 29EE512 (64KB)
STMicroelectronics M29F010B/ M29W010B (1 Megabit)
STMicroelectronics M29W040B (4 Megabit)
STMicroelectronics M29W400B (4 Megabit) variable sectors
MXIC MX29LV040 (4 Megabit)
PMC Pm39LV010(1Megabit) and PMC Pm39LV040 (4Megabit)

ale zadne flashnuti se nepovedlo (pritom verze biosu byla u dvou chipu nactena spravne). (Verzi updflash.exe jsem mel 3.35 12/19/2006 a zadnou novejsi se mi sehnat nepodarilo).

Zkousel jsem i jine PCI a jine konfigurace IRQ, bezvysledne.

Radic jsem zkousel na desce jako "IDE MASTER" a take nic.

Nekde jsem take vyhrabal, ze by mohl pomoc parametr kernelu ide=reverse. Jak jinak nez bezvysledne.

Jeste jen doplnim jak se radic komplet hlasi:

00:06.0 RAID bus controller: Silicon Image, Inc. SiI 3512 [SATALink/SATARaid] Serial ATA Controller (rev 01)
        Subsystem: Silicon Image, Inc. SiI 3512 SATARaid Controller
        Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
        Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- < TAbort- < MAbort- >SERR- < PERR- INTx-
        Latency: 32, Cache Line Size: 4 bytes
        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at ec00 [size=8]
        Region 1: I/O ports at e800 [size=4]
        Region 2: I/O ports at e400 [size=8]
        Region 3: I/O ports at e000 [size=4]
        Region 4: I/O ports at dc00 [size=16]
        Region 5: Memory at dffffe00 (32-bit, non-prefetchable) [size=512]
        Expansion ROM at dff00000 [disabled] [size=512K]
        Capabilities: [60] Power Management version 2
                Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-
        Kernel driver in use: SiI_IDE
        Kernel modules: sata_sil

Uz zacinam byt zoufalej