Administrace komentářů

HP Server s SAS radicem. Aktualne 2 disky v mirroru. Instalovan Centos 5.1 x86 - bez problemu.

FSTAB:

/dev/VolGroup00/LogVol00 /                       ext3    defaults        1 1
LABEL=/boot             /boot                   ext3    defaults        1 2
tmpfs                   /dev/shm                tmpfs   defaults        0 0
devpts                  /dev/pts                devpts  gid=5,mode=620  0 0
sysfs                   /sys                    sysfs   defaults        0 0
proc                    /proc                   proc    defaults        0 0
/dev/VolGroup00/LogVol01 swap                    swap    defaults        0 0

DMESG:

ioc0: SAS1068: Capabilities={Initiator}
scsi0 : ioc0: LSISAS1068, FwRev=00033200h, Ports=1, MaxQ=511, IRQ=233
  Vendor: HP        Model: DF072A8B56        Rev: HPD3
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: HP        Model: DF072A8B56        Rev: HPD3
  Type:   Direct-Access                      ANSI SCSI revision: 05
  Vendor: LSILOGIC  Model: Logical Volume    Rev: 3000
  Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sda: 142577664 512-byte hdwr sectors (73000 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write through
SCSI device sda: 142577664 512-byte hdwr sectors (73000 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 08
SCSI device sda: drive cache: write through
 sda: sda1 sda2
sd 0:1:0:0: Attached scsi disk sda

-------------------------------------------------------------------------

Rozhodli jsme se pridat dalsi mirror z 2x147GB disku. Pomoci LSI BIOSu jsme pridali new array. Bez problemu

Start systemu probihal v poradku do okamziku kdy se do konzole zacalo vypisovat:

Apr 25 14:21:28 v1 kernel: mptbase: ioc0: LogInfo(0x31110a00): Originator={PL}, Code={Reset}, SubCode(0x0a00)
Apr 25 14:21:28 v1 kernel: mptbase: ioc0: LogInfo(0x31120400): Originator={PL}, Code={Abort}, SubCode(0x0400)
Apr 25 14:21:29 v1 last message repeated 37 times
Apr 25 14:21:29 v1 kernel: mptscsih: ioc0: attempting task abort! (sc=f6ec4380)
Apr 25 14:21:29 v1 kernel: sd 0:1:1:0:
Apr 25 14:21:29 v1 kernel:         command: Write(10): 2a 00 02 bf 55 8d 00 01 40 00
Apr 25 14:21:29 v1 kernel: mptscsih: ioc0: task abort: FAILED (sc=f6ec4380)
Apr 25 14:21:29 v1 kernel: mptscsih: ioc0: attempting task abort! (sc=c2b3b080)
Apr 25 14:21:29 v1 kernel: sd 0:1:1:0:
Apr 25 14:21:29 v1 kernel:         command: Write(10): 2a 00 02 b7 52 f5 00 00 08 00
Apr 25 14:21:29 v1 kernel: mptscsih: ioc0: task abort: FAILED (sc=c2b3b080)
Apr 25 14:21:29 v1 kernel: mptscsih: ioc0: attempting task abort! (sc=c2b50500)
Apr 25 14:21:29 v1 kernel: sd 0:1:1:0:
Apr 25 14:21:29 v1 kernel:         command: Write(10): 2a 00 02 b7 53 0d 00 00 10 00
Apr 25 14:21:29 v1 kernel: mptscsih: ioc0: task abort: FAILED (sc=c2b50500)
Apr 25 14:21:29 v1 kernel: mptscsih: ioc0: attempting task abort! (sc=f62d2e00)
Apr 25 14:21:29 v1 kernel: sd 0:1:1:0:
Apr 25 14:21:29 v1 kernel:         command: Write(10): 2a 00 02 bf 77 0d 00 00 08 00
Apr 25 14:21:30 v1 kernel: mptscsih: ioc0: task abort: FAILED (sc=f62d2e00)
Apr 25 14:21:30 v1 kernel: mptscsih: ioc0: attempting task abort! (sc=f6eb9200)
Apr 25 14:21:30 v1 kernel: sd 0:1:1:0:
Apr 25 14:21:30 v1 kernel:         command: Write(10): 2a 00 02 bf 77 1d 00 00 38 00
Apr 25 14:21:30 v1 kernel: mptscsih: ioc0: task abort: FAILED (sc=f6eb9200)
Apr 25 14:21:30 v1 kernel: mptscsih: ioc0: attempting task abort! (sc=c2b50680)
Apr 25 14:21:30 v1 kernel: sd 0:1:1:0:
Apr 25 14:21:30 v1 kernel:         command: Write(10): 2a 00 02 c0 f2 e5 00 00 08 00
Apr 25 14:21:31 v1 kernel: mptscsih: ioc0: task abort: FAILED (sc=c2b50680)
Apr 25 14:21:31 v1 kernel: mptscsih: ioc0: attempting task abort! (sc=f6eb9680)

Server uz nenabehl v poradku. Po rebootu opet stejna situace.

Po vyjmuti disku a ponechani konfigurovaneho druheho pole server nabehl zpet do funkcniho stavu po kontrole fs.

Co je spatne? Jak pridat druhy mirror do systemu?