Administrace komentářů

Ahoj,
chtel bych se na vas obratit s HW problemem. Mam Lenovo ThinkPad x61s asi rok a bez problemu. Nicmene dokoupil sem si pamet a upgradoval sem 1G->2G. Nechal sem pres noc bezet memtest a vse OK. Jenze vcera zapnu notes a on pise : Disk Failure a pak cerna obrazovka, ale vypl sem a zapl znovu a vse OK nabehl. Posleze sem ale zjistil (nevim jestli to ma s diskem nebo s vymenou pameti souvislost), ze mi nehraje reproduktor (ani v Linuxu ani ve widlich), na sluchatka OK, ale repracek nefunguje. Myslite ze by vymena pameti mohla tohle zpusobit? Rikam si logicky ze ne, ale je divne ze to vse zacalo den po vymene pameti.
Jinak pamet je original Lenovo 2x1G.
A ve smartu sem nasel toto:

root@foton2:/home/david# smartctl -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===
Device Model:     ST9120822AS
Serial Number:    5LZ63S53
Firmware Version: 3.CLF
User Capacity:    120,034,123,776 bytes
Device is:        Not in smartctl database [for details use: -P showall]
ATA Version is:   7
ATA Standard is:  Exact ATA specification draft version not indicated
Local Time is:    Wed Oct 22 13:03:32 2008 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.

General SMART Values:
Offline data collection status:  (0x82)	Offline data collection activity
					was completed without error.
					Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0)	The previous self-test routine completed
					without error or no self-test has ever 
					been run.
Total time to complete Offline 
data collection: 		 ( 426) seconds.
Offline data collection
capabilities: 			 (0x5b) SMART execute Offline immediate.
					Auto Offline data collection on/off support.
					Suspend Offline collection upon new
					command.
					Offline surface scan supported.
					Self-test supported.
					No Conveyance Self-test supported.
					Selective Self-test supported.
SMART capabilities:            (0x0003)	Saves SMART data before entering
					power-saving mode.
					Supports SMART auto save timer.
Error logging capability:        (0x01)	Error logging supported.
					General Purpose Logging supported.
Short self-test routine 
recommended polling time: 	 (   1) minutes.
Extended self-test routine
recommended polling time: 	 (  57) minutes.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   095   081   034    Pre-fail  Always       -       227523671
  3 Spin_Up_Time            0x0003   099   098   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   095   095   020    Old_age   Always       -       5534
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   069   060   030    Pre-fail  Always       -       21518682357
  9 Power_On_Hours          0x0032   098   098   000    Old_age   Always       -       227701986166992
 10 Spin_Retry_Count        0x0013   100   100   034    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       852
187 Unknown_Attribute       0x0032   100   100   000    Old_age   Always       -       0
189 Unknown_Attribute       0x003a   001   001   000    Old_age   Always       -       2468
190 Temperature_Celsius     0x0022   056   044   045    Old_age   Always   In_the_past 741081132
191 G-Sense_Error_Rate      0x0032   100   100   000    Old_age   Always       -       1234
192 Power-Off_Retract_Count 0x0032   001   001   000    Old_age   Always       -       4294967162
193 Load_Cycle_Count        0x0022   001   001   000    Old_age   Always       -       241086
194 Temperature_Celsius     0x001a   044   056   000    Old_age   Always       -       44 (Lifetime Min/Max 0/19)
195 Hardware_ECC_Recovered  0x0012   083   065   000    Old_age   Always       -       227523671
196 Reallocated_Event_Count 0x0010   098   098   000    Old_age   Offline      -       26628797237574
197 Current_Pending_Sector  0x003e   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0000   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x0032   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0000   100   253   000    Old_age   Offline      -       0
202 TA_Increase_Count       0x0000   100   253   000    Old_age   Offline      -       0

SMART Error Log Version: 1
ATA Error Count: 1
	CR = Command Register [HEX]
	FR = Features Register [HEX]
	SC = Sector Count Register [HEX]
	SN = Sector Number Register [HEX]
	CL = Cylinder Low Register [HEX]
	CH = Cylinder High Register [HEX]
	DH = Device/Head Register [HEX]
	DC = Device Command Register [HEX]
	ER = Error register [HEX]
	ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 1 occurred at disk power-on lifetime: 2247 hours (93 days + 15 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  10 51 00 00 00 00 e0  Error: IDNF at LBA = 0x00000000 = 0

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  20 ff 01 00 00 00 e0 00      00:10:04.108  READ SECTOR(S)
  ef 10 03 ff ff 00 e0 00      00:10:04.108  SET FEATURES [Reserved for Serial ATA]
  ef 03 45 ff ff 00 e0 00      00:10:04.108  SET FEATURES [Set transfer mode]
  ef 03 0c ff ff 00 e0 00      00:10:04.108  SET FEATURES [Set transfer mode]
  c6 ff 10 ff ff 00 e0 00      00:10:04.076  SET MULTIPLE MODE

SMART Self-test log structure revision number 1

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

Otazky:
1. Co myslite ze ten disk, je OK bo je to budouci problem?
2. Jde nejak ten disk vice otestovat?
3. Nejaky napad, jak rozchodit repracek?
4. Reklamovali byste? (mam notes cca rok, zaruka je 3)
5. Muze to mit spojitost s tou vymenou pameti?
Predem diky za jakykoli nazor,
David