Administrace komentářů

# Generated by dhcpcd from eth0
# /etc/resolv.conf.head can replace this line
nameserver 192.168.0.1
# /etc/resolv.conf.tail can replace this line
/etc/resolv.conf (END) 

[jirka@amisek ~]$ ip -s li
1: lo: LOOPBACK,UP,LOWER_UP mtu 16436 qdisc noqueue state UNKNOWN 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    RX: bytes  packets  errors  dropped overrun mcast   
    2960       44       0       0       0       0      
    TX: bytes  packets  errors  dropped carrier collsns 
    2960       44       0       0       0       0      
2: eth0: BROADCAST,MULTICAST,UP,LOWER_UP mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
    link/ether 00:26:54:0e:85:5b brd ff:ff:ff:ff:ff:ff
    RX: bytes  packets  errors  dropped overrun mcast   
    2232631    2075     0       0       0       0      
    TX: bytes  packets  errors  dropped carrier collsns 
    301330     1778     0       0       0       0      
3: eth1: BROADCAST,MULTICAST mtu 1500 qdisc noop state DOWN qlen 1000
    link/ether 00:0c:6e:65:2e:f0 brd ff:ff:ff:ff:ff:ff
    RX: bytes  packets  errors  dropped overrun mcast   
    0          0        0       0       0       0      
    TX: bytes  packets  errors  dropped carrier collsns 
    0          0        0       0       0       0      
[jirka@amisek ~]$ ethtool -S eth0
bash: ethtool: příkaz nenalezen
[jirka@amisek ~]$ less /etc/resolv.conf 
[jirka@amisek ~]$ ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:26:54:0E:85:5B  
          inet addr:192.168.0.100  Bcast:192.168.0.255  Mask:255.255.255.0
          inet6 addr: fe80::226:54ff:fe0e:855b/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:2185 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1900 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:2297099 (2.1 Mb)  TX bytes:330706 (322.9 Kb)
          Interrupt:22 Base address:0x6000 

eth1      Link encap:Ethernet  HWaddr 00:0C:6E:65:2E:F0  
          BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:21 Base address:0xa000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:44 errors:0 dropped:0 overruns:0 frame:0
          TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:2960 (2.8 Kb)  TX bytes:2960 (2.8 Kb)

[jirka@amisek ~]$ 

# -----------------------------------------------------------------------
# NETWORKING
# -----------------------------------------------------------------------
#
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
#
HOSTNAME="amisek"

# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
#
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
#   - prefix an entry in INTERFACES with a ! to disable it
#   - no hyphens in your interface names - Bash doesn't like it
# 
# DHCP:     Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="dhcp"
#eth0="eth0 192.168.1.1 netmask 255.255.255.0 broadcast 192.168.1.255"
# eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
INTERFACES=(eth0)

# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
#   - prefix an entry in ROUTES with a ! to disable it
#
# gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
 
# Enable these network profiles at boot-up.  These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
#   - set to 'menu' to present a menu during boot-up (dialog package required)
#   - prefix an entry with a ! to disable it
#
# Network profiles are found in /etc/network.d
#
# This now requires the netcfg package
#
#NETWORKS=(main)