Administrace komentářů

smartctl 6.2 2013-03-29 r3806 [x86_64-linux-2.6.32-5-xen-amd64] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org

=== START OF INFORMATION SECTION ===
Model Family:     Seagate SV35.5
Device Model:     ST31000525SV
Serial Number:    9VP9D842
LU WWN Device Id: 5 000c50 02ca28ae1
Firmware Version: CV12
User Capacity:    1 000 204 886 016 bytes [1,00 TB]
Sector Size:      512 bytes logical/physical
Rotation Rate:    7200 rpm
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   ATA8-ACS T13/1699-D revision 4
SATA Version is:  SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is:    Mon Apr 15 15:46:49 2013 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status:  (0x82) Offline data collection activity
                                        was completed without error.
                                        Auto Offline Data Collection: Enabled.
Self-test execution status:      (   0) The previous self-test routine completed
                                        without error or no self-test has ever
                                        been run.
Total time to complete Offline
data collection:                (  609) seconds.
Offline data collection
capabilities:                    (0x7b) SMART execute Offline immediate.
                                        Auto Offline data collection on/off support.
                                        Suspend Offline collection upon new
                                        command.
                                        Offline surface scan supported.
                                        Self-test supported.
                                        Conveyance Self-test supported.
                                        Selective Self-test supported.
SMART capabilities:            (0x0003) Saves SMART data before entering
                                        power-saving mode.
                                        Supports SMART auto save timer.
Error logging capability:        (0x01) Error logging supported.
                                        General Purpose Logging supported.
Short self-test routine
recommended polling time:        (   1) minutes.
Extended self-test routine
recommended polling time:        ( 179) minutes.
Conveyance self-test routine
recommended polling time:        (   2) minutes.
SCT capabilities:              (0x10bb) SCT Status supported.
                                        SCT Error Recovery Control supported.
                                        SCT Feature Control supported.
                                        SCT Data Table supported.

SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000f   114   099   006    Pre-fail  Always       -       225291166
  3 Spin_Up_Time            0x0003   095   095   000    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   020    Old_age   Always       -       338
  5 Reallocated_Sector_Ct   0x0033   100   100   036    Pre-fail  Always       -       0
  7 Seek_Error_Rate         0x000f   089   060   030    Pre-fail  Always       -       847488703
  9 Power_On_Hours          0x0032   079   079   000    Old_age   Always       -       19089
 10 Spin_Retry_Count        0x0013   100   100   097    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   020    Old_age   Always       -       169
184 End-to-End_Error        0x0032   100   100   099    Old_age   Always       -       0
187 Reported_Uncorrect      0x0032   093   093   000    Old_age   Always       -       7
188 Command_Timeout         0x0032   100   098   000    Old_age   Always       -       42950328409
189 High_Fly_Writes         0x003a   089   089   000    Old_age   Always       -       11
190 Airflow_Temperature_Cel 0x0022   068   054   045    Old_age   Always       -       32 (Min/Max 15/32)
194 Temperature_Celsius     0x0022   032   046   000    Old_age   Always       -       32 (0 3 0 0 0)
195 Hardware_ECC_Recovered  0x001a   041   029   000    Old_age   Always       -       225291166
197 Current_Pending_Sector  0x0012   100   100   000    Old_age   Always       -       0
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0

SMART Error Log Version: 1
ATA Error Count: 7 (device log contains only the most recent five errors)
        CR = Command Register [HEX]
        FR = Features Register [HEX]
        SC = Sector Count Register [HEX]
        SN = Sector Number Register [HEX]
        CL = Cylinder Low Register [HEX]
        CH = Cylinder High Register [HEX]
        DH = Device/Head Register [HEX]
        DC = Device Command Register [HEX]
        ER = Error register [HEX]
        ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 7 occurred at disk power-on lifetime: 19046 hours (793 days + 14 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00   2d+11:30:25.305  READ FPDMA QUEUED
  61 00 08 ff ff ff 4f 00   2d+11:30:23.500  WRITE FPDMA QUEUED
  61 00 e8 ff ff ff 4f 00   2d+11:30:23.499  WRITE FPDMA QUEUED
  61 00 18 ff ff ff 4f 00   2d+11:30:23.497  WRITE FPDMA QUEUED
  61 00 08 ff ff ff 4f 00   2d+11:30:23.496  WRITE FPDMA QUEUED

Error 6 occurred at disk power-on lifetime: 19018 hours (792 days + 10 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00   1d+06:41:15.376  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00   1d+06:41:15.366  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00   1d+06:41:15.158  READ FPDMA QUEUED
  60 00 88 ff ff ff 4f 00   1d+06:41:13.630  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00   1d+06:41:13.630  READ FPDMA QUEUED

Error 5 occurred at disk power-on lifetime: 18939 hours (789 days + 3 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00  18d+01:58:44.396  READ FPDMA QUEUED
  60 00 08 ff ff ff 4f 00  18d+01:58:44.389  READ FPDMA QUEUED
  61 00 68 ff ff ff 4f 00  18d+01:58:44.388  WRITE FPDMA QUEUED
  61 00 30 ff ff ff 4f 00  18d+01:58:44.388  WRITE FPDMA QUEUED
  61 00 d0 ff ff ff 4f 00  18d+01:58:44.387  WRITE FPDMA QUEUED

Error 4 occurred at disk power-on lifetime: 18023 hours (750 days + 23 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 ff ff ff 0f  Error: UNC at LBA = 0x0fffffff = 268435455

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 08 ff ff ff 4f 00  29d+14:17:47.232  READ FPDMA QUEUED
  61 00 08 ff ff ff 4f 00  29d+14:17:44.871  WRITE FPDMA QUEUED
  61 00 08 ff ff ff 4f 00  29d+14:17:44.871  WRITE FPDMA QUEUED
  61 00 08 ff ff ff 4f 00  29d+14:17:44.870  WRITE FPDMA QUEUED
  61 00 08 ff ff ff 4f 00  29d+14:17:44.870  WRITE FPDMA QUEUED

Error 3 occurred at disk power-on lifetime: 15031 hours (626 days + 7 hours)
  When the command that caused the error occurred, the device was active or idle.

  After command completion occurred, registers were:
  ER ST SC SN CL CH DH
  -- -- -- -- -- -- --
  40 51 00 64 fd 00 00  Error: UNC at LBA = 0x0000fd64 = 64868

  Commands leading to the command that caused the error were:
  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  60 00 02 64 fd 00 40 00   2d+04:25:00.855  READ FPDMA QUEUED
  60 00 00 7e 41 9a 47 00   2d+04:25:00.758  READ FPDMA QUEUED
  60 00 c8 b6 40 9a 47 00   2d+04:25:00.757  READ FPDMA QUEUED
  60 00 3a 7c 40 9a 47 00   2d+04:25:00.757  READ FPDMA QUEUED
  60 00 08 74 40 9a 47 00   2d+04:25:00.757  READ FPDMA QUEUED

SMART Self-test log structure revision number 1
Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Extended offline    Completed without error       00%     15605         -
# 2  Extended offline    Completed without error       00%     15437         -

SMART Selective self-test log data structure revision number 1
 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing
Selective self-test flags (0x0):
  After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.