Administrace komentářů

Zdravím!

Dávám dohromady jistý servřík nadoma, nějakou dobu ta věc ležela ladem, teď jsem se k tomu vrátil a nainstaloval nový Devuan (beowulf/ceres) [jádro: 4.19.0-5-amd64 #1 SMP Debian 4.19.37-5 (2019-06-19). Původně tam byl nějaký Debian Wheezy, jádro snad 3.16 nebo 4.0. Ve stroji je pár 2,5" disků v mdraidu, které z nějakých technických důvodu nějaký čas nefungovaly (napájení atd). To je teď vyřešeno, jenže přestaly fungovat dva SATA porty, které visí na miniPCI kartě (od soudruha Číňaňa), kartá má v sobě AHCI kontrolér ASM1062.

Moje otázka: je třeba očekávat, že se jedná o sw problém s novým jádrem nebo že se nějak ten kontrolér poškodil? (Nový kontrolér stojí sice u Číňana pouhých 10 éček, ale putuje 2 měsíce a jiný nemám).

Relevantní část dmegs. Pokud jsou ty samé disky zapojené do jiného kontroléru, fungují bez problémů (včetně identického SATA kabelu):

[    0.913380] pci 0000:03:00.0: [1b21:0612] type 00 class 0x010601
[    0.925636] pci 0000:03:00.0: reg 0x10: [mem 0x00000000-0x00001fff]
[    0.926422] pci 0000:03:00.0: reg 0x14: [io  0x2018-0x201b]
[    0.927205] pci 0000:03:00.0: reg 0x18: [io  0x2000-0x2007]
[    0.927988] pci 0000:03:00.0: reg 0x1c: [io  0x2014-0x2017]
[    0.929821] pci 0000:03:00.0: reg 0x20: [io  0x2000-0x201f]
[    0.930608] pci 0000:03:00.0: reg 0x24: [mem 0xd0500000-0xd05001ff]
[    0.931395] pci 0000:03:00.0: reg 0x30: [mem 0xffff0000-0xffffffff pref]
[    0.945238] pci 0000:03:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:1c.3 (capable of 4.000 Gb/s with 5 GT/s x1 link)
[    0.951519] pci 0000:03:00.0: can't claim BAR 4 [io  0x2000-0x201f]: address conflict with 0000:03:00.0 [io  0x2000-0x2007]
[    0.993116] pnp 00:07: disabling [mem 0x00000000-0x00000fff] because it overlaps 0000:03:00.0 BAR 0 [mem 0x00000000-0x00001fff]
[    0.993121] pnp 00:07: disabling [mem 0x00000000-0x00000fff] because it overlaps 0000:03:00.0 BAR 0 [mem 0x00000000-0x00001fff]
[    1.004941] pci 0000:03:00.0: can't claim BAR 6 [mem 0xffff0000-0xffffffff pref]: no compatible bridge window
[    1.005132] pci 0000:03:00.0: BAR 6: assigned [mem 0xd0510000-0xd051ffff pref]
[    1.005137] pci 0000:03:00.0: BAR 0: assigned [mem 0xd0502000-0xd0503fff]
[    1.005463] pci 0000:03:00.0: BAR 4: assigned [io  0x2020-0x203f]
[    4.419962] ahci 0000:03:00.0: SSS flag set, parallel bus scan disabled
[    4.422457] ahci 0000:03:00.0: AHCI 0001.0200 32 slots 2 ports 6 Gbps 0x3 impl SATA mode
[    4.422462] ahci 0000:03:00.0: flags: 64bit ncq sntf stag led clo pmp pio slum part ccc sxs 
[    4.426395] ata9: FORCE: PHY spd limit set to 3.0Gbps
[    4.426399] ata9: SATA max UDMA/133 abar m512@0xd0500000 port 0xd0500100 irq 28
[    4.426513] ata10: FORCE: PHY spd limit set to 3.0Gbps
[    4.426515] ata10: SATA max UDMA/133 abar m512@0xd0500000 port 0xd0500180 irq 28
[    4.902598] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[    5.235694] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[   10.470645] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[   10.480359] ata9.00: ATA-8: ST1500LM006 HN-M151RAD, 2BC10001, max UDMA/133
[   10.480364] ata9.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[   15.625673] ata9.00: qc timeout (cmd 0xec)
[   15.664972] ahci 0000:03:00.0: AHCI controller unavailable!
[   15.704289] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   15.704293] ata9.00: revalidation failed (errno=-5)
[   15.723948] ata9: limiting SATA link speed to 1.5 Gbps
[   15.723951] ata9.00: limiting speed to UDMA/133:PIO3
[   15.743610] ahci 0000:03:00.0: AHCI controller unavailable!
[   16.238670] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   16.304681] ata9.00: failed to enable AA (error_mask=0x1)
[   16.310279] ata9.00: failed to set xfermode (err_mask=0x40)
[   16.316126] ata9.00: disabled
[   17.247690] ata9: softreset failed (device not ready)
[   17.252918] ata9: reset failed (errno=-19), retrying in 10 secs
[   27.254587] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[   27.264409] ata9.00: ATA-8: ST1500LM006 HN-M151RAD, 2BC10001, max UDMA/133
[   27.264414] ata9.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[   27.402477] ahci 0000:03:00.0: AHCI controller unavailable!
[   27.408277] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[   27.408280] ata9.00: revalidation failed (errno=-5)
[   41.440289] ata9: softreset failed (device not ready)
[   41.445587] ata9: reset failed (errno=-19), retrying in 1 secs
[   42.295557] ahci 0000:03:00.0: AHCI controller unavailable!
[   44.940701] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 3F0)
[   44.941037] ata9.00: link online but device misclassified
[   50.185694] ata9.00: qc timeout (cmd 0xec)
[   50.186189] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   50.186192] ata9.00: revalidation failed (errno=-5)
[   50.191356] ata9: limiting SATA link speed to 1.5 Gbps
[   50.670671] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[   50.691244] ata9.00: configured for UDMA/133
[   50.692516] sd 8:0:0:0: [sdh] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[   50.692521] sd 8:0:0:0: [sdh] 4096-byte physical blocks
[   50.692553] sd 8:0:0:0: [sdh] Write Protect is off
[   50.692557] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[   50.692607] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   52.057120] ata9: illegal qc_active transition (01000000-gt;ffffffff)
[   52.116130] ata9.00: exception Emask 0x52 SAct 0x1000000 SErr 0xffffffff action 0xe frozen
[   52.124484] ata9: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[   52.140182] ata9.00: failed command: READ FPDMA QUEUED
[   52.145408] ata9.00: cmd 60/08:c0:00:00:00/00:00:00:00:00/40 tag 24 ncq dma 4096 in
[   52.161188] ata9.00: status: { DRDY }
[   52.165055] ata9: hard resetting link
[   52.175086] ahci 0000:03:00.0: AHCI controller unavailable!
[   52.922772] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[   52.991378] ata10.00: ATA-8: ST1500LM006 HN-M151RAD, 2BC10008, max UDMA/133
[   52.991384] ata10.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[   53.119445] ata10.00: failed to enable AA (error_mask=0x1)
[   53.125360] ata10.00: configured for UDMA/133
[   53.856096] ata9: SATA link down (SStatus 123 SControl FFFFFFFF)
[   53.876152] ata9.00: configured for UDMA/133
[   53.876184] ata9: EH complete
[   54.072364] ata10: softreset failed (device not ready)
[   54.077645] ata10: reset failed (errno=-19), retrying in 10 secs
[   63.253975] ahci 0000:03:00.0: AHCI controller unavailable!
[   64.404131] ata10: failed to resume link (SControl FFFFFFFF)
[   64.561886] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 3F0)
[   64.562333] ata10.00: link online but device misclassified
[   64.660269] ata10.00: failed to read native max address (err_mask=0x1)
[   64.660273] ata10.00: HPA support seems broken, skipping HPA handling
[   64.660276] ata10.00: revalidation failed (errno=-5)
[   65.710890] udevd[103]: worker [115] /devices/pci0000:00/0000:00:1c.3/0000:03:00.0 is taking a long time
[   69.642675] ata9.00: limiting speed to UDMA/100:PIO4
[   69.642684] ata9.00: exception Emask 0x73 SAct 0x10000000 SErr 0xffffffff action 0xe frozen
[   69.651355] ata9.00: irq_stat 0xffffffff, unknown FIS 00000000 00000000 00000000 00000000, host bus 
[   69.660704] ata9: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[   69.676636] ata9.00: failed command: READ FPDMA QUEUED
[   69.682099] ata9.00: cmd 60/08:e0:00:00:00/00:00:00:00:00/40 tag 28 ncq dma 4096 in
[   69.698447] ata9.00: status: { DRDY }
[   69.702321] ata9: hard resetting link
[   70.115854] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[   70.144370] ata10.00: configured for UDMA/133
[   70.145654] sd 9:0:0:0: [sdi] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[   70.145661] sd 9:0:0:0: [sdi] 4096-byte physical blocks
[   70.145697] sd 9:0:0:0: [sdi] Write Protect is off
[   70.145703] sd 9:0:0:0: [sdi] Mode Sense: 00 3a 00 00
[   70.145748] sd 9:0:0:0: [sdi] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   72.057892] ata9: COMRESET failed (errno=-32)
[   72.101316] ata9: reset failed (errno=-32), retrying in 8 secs
[   79.896843] ata9: hard resetting link
[   79.916492] ahci 0000:03:00.0: AHCI controller unavailable!
[   81.056827] ata9: failed to resume link (SControl FFFFFFFF)
[   81.117199] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 3F0)
[   81.117822] ata9.00: link online but device misclassified
[   86.281695] ata9.00: qc timeout (cmd 0xec)
[   86.316083] ahci 0000:03:00.0: AHCI controller unavailable!
[   86.355407] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   86.355411] ata9.00: revalidation failed (errno=-5)
[   86.360373] ata9: hard resetting link
[   86.375062] ahci 0000:03:00.0: AHCI controller unavailable!
[   87.485914] ata9: failed to resume link (SControl FFFFFFFF)
[   87.643367] ata9: SATA link up lt;unknowngt; (SStatus FFFFFFFF SControl 3F0)
[   87.682502] ata10: illegal qc_active transition (00000001-gt;ffffffff)
[   87.721942] ata9.00: link status unknown, clearing UNKNOWN to NONE
[   87.729780] ata10.00: exception Emask 0x2 SAct 0x1 SErr 0x0 action 0x6 frozen
[   87.737120] ata10.00: failed command: READ FPDMA QUEUED
[   87.742549] ata10.00: cmd 60/08:00:18:00:00/00:00:00:00:00/40 tag 0 ncq dma 4096 in
[   87.758535] ata10.00: status: { DRDY }
[   87.762392] ata10: hard resetting link
[   88.238656] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[   93.449667] ata10.00: qc timeout (cmd 0xec)
[   93.482443] ahci 0000:03:00.0: AHCI controller unavailable!
[   93.521763] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   93.521766] ata10.00: revalidation failed (errno=-5)
[   93.526866] ata10: hard resetting link
[   93.541423] ahci 0000:03:00.0: AHCI controller unavailable!
[   94.022626] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[   97.801676] ata9.00: qc timeout (cmd 0xec)
[   97.837327] ahci 0000:03:00.0: AHCI controller unavailable!
[   97.843223] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[   97.843226] ata9.00: revalidation failed (errno=-5)
[   97.848715] ata9: hard resetting link
[   97.860823] ata10.00: configured for UDMA/133
[   97.860858] ata10: EH complete
[   98.937751] ata9: link resume succeeded after 4 retries
[   99.174246] ata10: illegal qc_active transition (00008000-gt;ffffffff)
[   99.252916] ata10.00: exception Emask 0x52 SAct 0x8000 SErr 0xffffffff action 0xe frozen
[   99.261393] ata10: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[   99.277442] ata10.00: failed command: READ FPDMA QUEUED
[   99.282760] ata10.00: cmd 60/08:78:18:00:00/00:00:00:00:00/40 tag 15 ncq dma 4096 in
[   99.298917] ata10.00: status: { DRDY }
[   99.302844] ata10: hard resetting link
[  100.178668] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[  100.327206] ata10.00: configured for UDMA/133
[  100.327237] ata10: EH complete
[  100.540679] ata9: softreset failed (device not ready)
[  100.545980] ata9: reset failed (errno=-19), retrying in 8 secs
[  108.041658] ata9: hard resetting link
[  108.060949] ahci 0000:03:00.0: AHCI controller unavailable!
[  109.201274] ata9: failed to resume link (SControl FFFFFFFF)
[  109.358898] ata9: SATA link up lt;unknowngt; (SStatus FFFFFFFF SControl 3F0)
[  109.359795] ata9.00: link online but device misclassified
[  109.360386] sdi: detected capacity change from 0 to 1500301910016
[  109.360635] sd 9:0:0:0: [sdi] Attached SCSI disk
[  141.065684] ata9.00: qc timeout (cmd 0xec)
[  141.100922] ahci 0000:03:00.0: AHCI controller unavailable!
[  141.140238] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  141.140241] ata9.00: revalidation failed (errno=-5)
[  141.145324] ata9.00: disabled
[  141.159904] ata9: hard resetting link
[  141.638626] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[  141.681835] ata9.00: failed to IDENTIFY (I/O error, err_mask=0x1)
[  146.697680] ata9: hard resetting link
[  147.174635] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[  147.184309] ata9.00: ATA-8: ST1500LM006 HN-M151RAD, 2BC10001, max UDMA/133
[  147.184314] ata9.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 32), AA
[  147.194852] ata9.00: configured for UDMA/133
[  147.194882] sd 8:0:0:0: [sdh] tag#28 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  147.194887] sd 8:0:0:0: [sdh] tag#28 Sense Key : Illegal Request [current] 
[  147.194892] sd 8:0:0:0: [sdh] tag#28 Add. Sense: Unaligned write command
[  147.194898] sd 8:0:0:0: [sdh] tag#28 CDB: Read(10) 28 00 00 00 00 00 00 00 08 00
[  147.194901] print_req_error: I/O error, dev sdh, sector 0
[  147.200557] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.207755] ata9: EH complete
[  147.213383] print_req_error: I/O error, dev sdh, sector 0
[  147.218902] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.231533] print_req_error: I/O error, dev sdh, sector 0
[  147.237212] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.249645] print_req_error: I/O error, dev sdh, sector 0
[  147.255247] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.267774] print_req_error: I/O error, dev sdh, sector 0
[  147.273370] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.285716] print_req_error: I/O error, dev sdh, sector 0
[  147.291294] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.303662] print_req_error: I/O error, dev sdh, sector 0
[  147.309163] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.321413] print_req_error: I/O error, dev sdh, sector 0
[  147.326922] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.333896] Dev sdh: unable to read RDB block 0
[  147.344221] print_req_error: I/O error, dev sdh, sector 0
[  147.349722] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.362236] print_req_error: I/O error, dev sdh, sector 0
[  147.367897] Buffer I/O error on dev sdh, logical block 0, async page read
[  147.386028]  sdh: unable to read partition table
[  147.386068] ata9.00: detaching (SCSI 8:0:0:0)
[  147.387013] sd 8:0:0:0: [sdh] Attached SCSI disk
[  147.387731] sd 8:0:0:0: [sdh] Synchronizing SCSI cache
[  147.388682] sd 8:0:0:0: [sdh] Stopping disk
[  177.994433] ahci 0000:03:00.0: AHCI controller unavailable!
[  178.053717] ata10: limiting SATA link speed to 1.5 Gbps
[  178.053724] ata10.00: exception Emask 0x0 SAct 0x8000 SErr 0x0 action 0x6 frozen
[  178.061352] ata10.00: failed command: READ FPDMA QUEUED
[  178.066678] ata10.00: cmd 60/08:78:20:7b:a8/00:00:ae:00:00/40 tag 15 ncq dma 4096 in
[  178.082278] ata10.00: status: { DRDY }
[  178.086294] ata10: hard resetting link
[  178.102558] ahci 0000:03:00.0: AHCI controller unavailable!
[  178.658609] ata10: SATA link up 3.0 Gbps (SStatus 123 SControl 3F0)
[  179.145242] ata10.00: failed to enable AA (error_mask=0x1)
[  179.150999] ata10.00: configured for UDMA/133
[  179.846763] ata9: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[  180.510978] ata9.00: configured for UDMA/133
[  180.510989] ata9.00: device reported invalid CHS sector 0
[  180.511036] sd 8:0:0:0: [sdh] Start/Stop Unit failed: Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  180.511042] sd 8:0:0:0: [sdh] Sense Key : Illegal Request [current] 
[  180.511046] sd 8:0:0:0: [sdh] Add. Sense: Unaligned write command
[  180.563300] sd 8:0:0:0: [sdh] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
[  180.563307] sd 8:0:0:0: [sdh] 4096-byte physical blocks
[  180.563341] sd 8:0:0:0: [sdh] Write Protect is off
[  180.563346] sd 8:0:0:0: [sdh] Mode Sense: 00 3a 00 00
[  180.563397] sd 8:0:0:0: [sdh] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[  180.670690] ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[  180.689131] ata10.00: configured for UDMA/133
[  180.689157] sd 9:0:0:0: [sdi] tag#15 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  180.689163] sd 9:0:0:0: [sdi] tag#15 Sense Key : Illegal Request [current] 
[  180.689168] sd 9:0:0:0: [sdi] tag#15 Add. Sense: Unaligned write command
[  180.689174] sd 9:0:0:0: [sdi] tag#15 CDB: Read(10) 28 00 ae a8 7b 20 00 00 08 00
[  180.689179] print_req_error: I/O error, dev sdi, sector 2930277152
[  180.695669] ata10: EH complete
[  207.597542] udevd[103]: worker [120] /devices/pci0000:00/0000:00:1c.3/0000:03:00.0/ata10/host9/target9:0:0/9:0:0:0/block/sdi is taking a long time
[  210.759171] ata9: limiting SATA link speed to 1.5 Gbps
[  210.759177] ata9.00: exception Emask 0x52 SAct 0x20000 SErr 0xffffffff action 0xe frozen
[  210.767694] ata9: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[  210.783586] ata9.00: failed command: READ FPDMA QUEUED
[  210.788866] ata9.00: cmd 60/08:88:00:00:00/00:00:00:00:00/40 tag 17 ncq dma 4096 in
[  210.804921] ata9.00: status: { DRDY }
[  210.808780] ata9: hard resetting link
[  210.827969] ahci 0000:03:00.0: AHCI controller unavailable!
[  210.886974] ata10.00: exception Emask 0x52 SAct 0x200000 SErr 0xffffffff action 0xe frozen
[  210.895448] ata10: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[  210.911575] ata10.00: failed command: READ FPDMA QUEUED
[  210.917099] ata10.00: cmd 60/08:a8:20:7b:a8/00:00:ae:00:00/40 tag 21 ncq dma 4096 in
[  210.933225] ata10.00: status: { DRDY }
[  210.937069] ata10: hard resetting link
[  210.955765] ahci 0000:03:00.0: AHCI controller unavailable!
[  211.881778] ata9: link resume succeeded after 3 retries
[  212.113768] ata10: link resume succeeded after 4 retries
[  215.547449] ata10: SATA link up 1.5 Gbps (SStatus 113 SControl 3F0)
[  215.547788] ata10.00: link online but device misclassified
[  217.866583] ata9: SATA link up 1.5 Gbps (SStatus 113 SControl 3F0)
[  220.681669] ata10.00: qc timeout (cmd 0xec)
[  220.682541] ata10.00: failed to IDENTIFY (I/O error, err_mask=0x4)
[  220.682544] ata10.00: revalidation failed (errno=-5)
[  220.687670] ata10: hard resetting link
[  220.700542] ata9.00: configured for UDMA/133
[  220.700553] ata9.00: device reported invalid CHS sector 0
[  220.700577] ata9: EH complete
[  221.777784] ata10: link resume succeeded after 4 retries
[  223.864574] sd 8:0:0:0: [sdh] Attached SCSI disk
[  223.864812] sdh: detected capacity change from 0 to 1500301910016
[  224.777320] ata10: softreset failed (device not ready)
[  224.782541] ata10: reset failed (errno=-19), retrying in 6 secs
[  230.921659] ata10: hard resetting link
[  230.940997] ahci 0000:03:00.0: AHCI controller unavailable!
[  232.081324] ata10: failed to resume link (SControl FFFFFFFF)
[  232.239059] ata10: SATA link down (SStatus C00040 SControl 3F0)
[  237.321663] ata10: hard resetting link
[  237.438903] ata9.00: exception Emask 0x73 SAct 0x20 SErr 0xffffffff action 0xe frozen
[  237.446995] ata9.00: irq_stat 0xffffffff, unknown FIS 00000000 00000000 00000000 00000000, host bus 
[  237.456550] ata9: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[  237.472786] ata9.00: failed command: READ FPDMA QUEUED
[  237.478159] ata9.00: cmd 60/08:28:80:7a:a8/00:00:ae:00:00/40 tag 5 ncq dma 4096 in
[  237.494209] ata9.00: status: { DRDY }
[  237.497981] ata9: hard resetting link
[  237.517515] ahci 0000:03:00.0: AHCI controller unavailable!
[  237.853733] ata10: SATA link down (SStatus 0 SControl 3F0)
[  237.854187] ata10.00: disabled
[  237.854310] ata10.00: device reported invalid CHS sector 0
[  237.854550] sd 9:0:0:0: [sdi] tag#21 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  237.854555] sd 9:0:0:0: [sdi] tag#21 Sense Key : Illegal Request [current] 
[  237.854560] sd 9:0:0:0: [sdi] tag#21 Add. Sense: Unaligned write command
[  237.854565] sd 9:0:0:0: [sdi] tag#21 CDB: Read(10) 28 00 ae a8 7b 20 00 00 08 00
[  237.854569] print_req_error: I/O error, dev sdi, sector 2930277152
[  237.861066] Buffer I/O error on dev sdi, logical block 366284644, async page read
[  237.868708] ata10: EH complete
[  237.868725] ata10.00: detaching (SCSI 9:0:0:0)
[  237.870738] sd 9:0:0:0: [sdi] Synchronizing SCSI cache
[  237.870817] sd 9:0:0:0: [sdi] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  237.870822] sd 9:0:0:0: [sdi] Stopping disk
[  237.870843] sd 9:0:0:0: [sdi] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  238.255109] ata9: SATA link down (SStatus 0 SControl 310)
[  243.465660] ata9: hard resetting link
[  243.782347] ata9: SATA link down (SStatus 0 SControl 310)
[  248.841669] ata9: hard resetting link
[  249.158180] ata9: SATA link down (SStatus 0 SControl 310)
[  249.158633] ata9.00: disabled
[  249.158998] sd 8:0:0:0: [sdh] tag#5 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[  249.159003] sd 8:0:0:0: [sdh] tag#5 Sense Key : Illegal Request [current] 
[  249.159008] sd 8:0:0:0: [sdh] tag#5 Add. Sense: Unaligned write command
[  249.159013] sd 8:0:0:0: [sdh] tag#5 CDB: Read(10) 28 00 ae a8 7a 80 00 00 08 00
[  249.159017] print_req_error: I/O error, dev sdh, sector 2930276992
[  249.165483] ata9: EH complete
[  249.165516] ata9.00: detaching (SCSI 8:0:0:0)
[  249.165553] print_req_error: I/O error, dev sdh, sector 2930276992
[  249.171927] Buffer I/O error on dev sdh, logical block 366284624, async page read
[  249.181103] sd 8:0:0:0: [sdh] Synchronizing SCSI cache
[  249.181180] sd 8:0:0:0: [sdh] Synchronize Cache(10) failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
[  249.181184] sd 8:0:0:0: [sdh] Stopping disk
[  249.181203] sd 8:0:0:0: [sdh] Start/Stop Unit failed: Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK